Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, and ceiling plates without cutting of insulation or plates. Roughed-in dimensions shall be prepared by the Contractor to accomplish this requirement. The Contractor shall locate all equipment that must be serviced, operated, or maintained in fully accessible positions. This provision includes but is not limited to valves, traps, cleanouts, motors, controllers, switchgear, drain points, filter, access doors, and fire dampers. If spaces, dimensions, or other design conditions do not permit compliance with the present article, the Contractor shall file a request in writing with the Design Professional for additional instructions, furnishing a copy to the Owner.
Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, and ceiling plates without cutting of insulation or plates. Roughed-in dimensions shall be prepared by the CM/GC to accomplish this requirement. The CM/GC shall locate all equipment that must be serviced, operated, or maintained in fully accessible positions. This provision includes but is not limited to valves, traps, cleanouts, motors, controllers, switchgear, drain points, filter, access doors, and fire dampers. If spaces, dimensions, or other design conditions do not permit compliance with the present article, the CM/GC shall file a request in writing with the Design Professional for additional instructions, furnishing a copy to the Owner.
Space Conditions. Day hours require that the hall and grounds be cleaned and vacated by the agreed upon time. Evening hours require that hall and grounds be cleaned and vacated by midnight.
Space Conditions. 1.9.26 Cutting, Patching, and Fitting.
Space Conditions. A. All work shall fit the spaces available. Verify all dimensions of the work before commencing fabrication and/or installation.
B. Minor deviations from the drawings required to conform to space conditions and to provide the required operation, service, or maintenance accessibility shall be made at no additional cost, and subject to approval.
C. Piping and equipment shall not be installed in electrical equipment rooms. Outside of electrical equipment rooms, do not run piping or locate equipment, with respect to switchboards, panel boards, power panels, motor control centers or dry type transformers: Replace Electrical Heating Mechanical System at Xxxxxx Xxxx with Gas-Fired Boiler General Provisions - Plumbing
Space Conditions. All pipes passing through floors, walls, and ceilings shall be inSsECtaTlIlOeNd3w–iCthONsSuTfRfiUcCieTnIOtNsPpHaAcSeE between them to permit installation of pipe insulation and floor, wall, and ceiling platPeAsRTw1it–hCoOuNt ScTuRtUtiCnTgIONofPHinAsSuElSaEtiRoVnICEoSr
Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, and ceiling plates without cutting of insulation or plates. Roughing dimensions shall be prepared by the Construction Manager to accomplish this requirement. The Construction Manager shall locate all equipment that must be serviced, operated, or maintained in fully accessible positions. This provision includes but is not limited to valves, traps, cleanouts, motors, controllers, switchgear, drain points, and fire dampers. If spaces, dimensions, or other design conditions do not permit compliance with the present article, the Construction Manager shall file a demand in writing with the Architect for additional instructions, furnishing a copy of the aforesaid demand to the Owner.
Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, and ceiling plates without cutting of insulation or plates. The Contractor shall locate all equipment that must be serviced, operated, or maintained in fully accessible positions.
Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, ceiling, and other components without compromise or cutting of insulation or other components. Roughed-in dimensions shall be prepared by CM to accomplish this requirement. CM shall anticipate and locate all equipment that must be serviced, operated, or maintained in fully accessible positions. This provision includes but is not limited to valves, traps, cleanouts, motor, controllers, switchgear, drain points, filters, access doors, and fire dampers. If spaces, dimension, or other design conditions do not permit compliance with this paragraph, CM shall submit to Design Professional and the ADR an RFI seeking guidance and direction before installing related Work.
Space Conditions. All pipes passing through floors, walls, and ceilings shall be installed with sufficient space between them to permit installation of pipe insulation and floor, wall, ceiling, and other components without compromise or cutting of insulation or other components. Roughed-in dimensions shall be prepared by Design-Builder to accomplish this requirement. Design-Builder shall anticipate and locate all equipment that must be serviced, operated, or maintained in fully accessible positions. This provision includes but is not limited to valves, traps, cleanouts, motor, controllers, switchgear, drain points, filters, access doors, and fire dampers. If spaces, dimension, or other design conditions do not permit compliance with this paragraph, Design-Builder shall submit to Design Professional and the ADR an RFI seeking guidance and direction before installing related Work.
