Common use of Specifications and Drawings for Construction Clause in Contracts

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite and (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer Technical Project Officer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite andand necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) ), Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure ensure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite andand necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One the Scope of Work at no costadditional costs. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite andand necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite andand necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications. (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work.to (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.

Specifications and Drawings for Construction. (a) Seller shall be furnished the number of drawings and specifications specified in Division One at no cost. (b) Seller shall keep on the work site a copy of the drawings and specifications and shall at all times give Company access thereto. Anything mentioned in the specifications and not shown on the drawings, or shown on the drawings and not mentioned in the specifications, shall be of like effect as if shown or mentioned in both. In case of difference between drawings and specifications, the specifications shall govern. Within the specifications, Division One (the "Special Conditions") shall govern. In case of discrepancy in the figures, in the drawings, or in the remainder of the specifications, the matter shall be promptly submitted to the Construction Engineer and the Subcontract Administrator, who shall promptly make a determination in writing. Any adjustment by Seller without such a determination shall be at its own risk and expense. Company shall furnish from time to time such detailed drawings and other information as considered necessary, unless otherwise provided. (1) The drawings and specifications incorporated into this Agreement are intended to include everything requisite andand necessary to complete the entire work properly, notwithstanding the fact that every item necessarily involved may not be specifically mentioned. (2) Omissions from the drawings or specifications or the misdescription of details of work that are manifestly necessary to carry out the intent of the drawings and specifications, or that are customarily performed, shall not relieve Seller from performing such omitted or misdescribed details of the work, but they shall be performed as if fully and correctly set forth and described in the drawings and specifications.to (3) The specifications and drawings may identify and list quantities of items to be furnished and installed by Seller. These identifications may be incomplete and the quantities are estimates only. Seller is responsible for furnishing the items and quantities manifestly necessary to carry out the intent of the drawings and specifications. (4) The drawings furnished by Company are, in general, to scale. Scales shown on a microfilmed reproduced drawing change in proportion to the reduction of the drawing from original size. Figured dimensions shall always be followed and the drawings not scaled. (5) Prior to fabricating any item (structural steel, piping, ductwork, etc.) Seller shall field-verify all dimensions critical to the installation. Any discrepancies between existing or new conditions and the drawings shall be reported to Company for resolution. (6) The specifications are divided into sections for convenience only, and such sections do not define or establish the limits of work of any subcontractor. It is Seller's responsibility to define lower-tier subcontractors' limits of work and to insure that all lower-tier subcontractors and suppliers at whatever level are familiar with all provisions of this Agreement that may affect their work. (7) The data sheet equipment numbers are not unique. Multiple pieces of equipment may utilize the same number. Seller shall determine the quantity of equipment and material needed to complete the work.