Spiking Sample Clauses

Spiking. All rail holding spikes shall be started with the head pointed toward the rail and driven vertically and square with the rail and so driven as to allow 1/8" to 3/16" in the space between the under side of the head of the spike and the top of the base of the rail. In no case shall the spikes be over-driven. Rail holding spiking arrangement shall be in accordance with the Contract Documents. Plate holding spikes shall be started with the head pointed toward the rail and driven vertically so head has full bearing against the tie plate. Plate holding spiking arrangement shall be in accordance with the Contract Documents. No spikes shall be driven against the ends of joint bars. Care shall be taken not to strike rail or fastenings when driving spikes. Spikes which are bent while being installed, and do not meet proper alignment, or designated head contact, will be removed. The hole shall be plugged properly with a treated tie plug, and a new spike installed. Timber spiking for standard tie plates shall conform to the following criteria: Degree of Curve Spike Pattern 0-00 to 3-00 2 rail holding 3-01' to 8-00' 2 rail holding and 1 plate holding – field side 8-01' to 12-30' 2 rail holding and 2 plate holding – 1 field side and 1 gauge side 12-31' to 16-00' 3 rail holding and 2 plate holding – 1 field side and 1 gauge side 16-01' to 18-00' 3 rail holding and 3 plate holding – 2 field side and 1 gauge side 18-01' to 20-00' 4 rail holding and 4 plate holding – 2 field side and 2 gauge side Note: Timber spiking for hook plates and twin tie plates (hook, flat or ridged) shall require only one spike at the ends of plate so as not to spike kill timber.
AutoNDA by SimpleDocs

Related to Spiking

  • Scratches (Q) appliance malfunctions and any resultant leak there from; (R) any stain, soiling or damage resulting from everyday use or which has built up over time, e.g. hair, body or suntan oils and/or lotions; (S) signs of soiling include darkened areas where the body comes into contact with the furniture (these darkened areas are signs of soil build-up, which is not covered); (T) general maintenance and overall cleaning of the furniture is the consumer’s responsibility; (U) damage due to harsh or corrosive chemicals; (V) acids, including without limitation, dyes and inks (except ballpoint), plant food and fertilizer and bleach, gum; (W) any non-operating part or decorative parts such as hinges, knobs, handles, or shelves; (X) coverage under another insurance program; (Y) delivery and/or redelivery and/or loss or damage to the Covered Product while in the course of transit; (Z) design deficiency; (AA) fabrics with “X” cleaning codes and non-colorfast fabrics and leathers; (AB) odors; (AC) variation of the color, or graining of wood or wood products, marble or leather; (AD) split leathers used in seat cushions, back cushions or top or inside arm areas; (AE) natural markings on leather, such as, healed scars, insect bites, brand marks or wrinkles, or suede, and leathers with embossed patterns other than those stimulating natural cowhide; (AF) non- bovine leathers, and other buffed leathers; (AG) stains, color loss or damage resulting from cleaning methods or products (detergents, abrasives or other harsh cleaning agents) other than those recommended by the furniture manufacturer; (AH) stone or sand abrasion; (AI) loss or damage resulting from: pre-existing conditions known to You; (AJ) wear related issues, such as but not limited to, fading, wear, seam separation, stress tears, loss of foam resiliency, pilling or fraying of any fabric on all types of furniture; (AK) color loss or cracking and peeling on any leather or vinyl; (AL) splits or bi-cast leather; (AM) furniture that is used for commercial, institutional, outdoor or rental purposes; (AN) Customer’s Own Material furniture; (AO) wicker, rattan, and teakwood furniture; (AP) massage chairs; (AQ) stains or damage to suede, split-grain leather hide or exotic leathers; (AR) manufacturer quality issues such as stress tears, fabric flaws, fading, color loss or change, loss of foam or resiliency, cracking and peeling of leather or vinyl, natural leather markings, and defects in design and workmanship; (AS) Stains or damage that occur during assembly, delivery, installation, before furniture is delivered to your residence, while the furniture is located outside of your residence, while the furniture is in storage or being moved to or from storage or between residences; (AT) Wear & Tear caused by repeated use such as scuffing, soiling, hair/body oil, perspiration, surface abrasions, pilling or fraying of fabric, loose joints; (AU) Stains or damage covered under any manufacturer warranty, recall, homeowner, renter or other insurance policy; (AV) Stains or damage caused by structural problems, appliance malfunctions, Acts of God or natural disasters, theft, vandalism or illegal activity (AW) Stains or damage caused by independent contractors Specific to Home Automation: In additional to the exclusions listed above, this Agreement does not cover any loss, repairs or damage caused by or resulting from: (A) pre-existing conditions incurred or known to you (pre-existing means a condition prior to Plan issuance); (B) any repair covered by a manufacturer’s warranty or any insurance; (C) installation, or improper installation; or improper installation of customer replaceable components, modules, parts or peripherals; (D) damage or failure due to causes beyond our control such as environmental conditions, exposure to weather conditions or acts of nature including, but not limited to: fire, floods, smoke, sand, dirt, lightning, moisture, water damage, freezes, storms, wind, windstorm, hail, earthquake, animal or insect infestation, etc.; (E) damage or failure caused by riot, nuclear radiation, war, hostile action, or radioactive contamination, etc.; (F) battery failure or leakage; (G) collision, collapse, or explosion; (H) liquid spillage of any kind; (I) signal reception, transmission problems resulting from external causes, interruption of electrical service, loss of power, improper use of electrical/power, power “brown-out”, power overload or power surge (unless covered in the Special Features section of this document); (J) neglect, misuse, abuse, intentional damage, malicious mischief, theft, mysterious disappearance, vandalism or accidental damage; damage cause by dropping (K) rust, corrosion, warping, bending, etc.; (L) damage, warping, bending or rusting of any kind to the housing, cabinetry, outside casing or frame of the product; (M) any non-operating part, including but not limited to plastic, or decorative parts such as hinges, knobs, door liners, glass, handles, masks, rack rollers, shelves, etc.; (N) loss of or repair to components within the product not originally covered by the manufacturer’s warranty; (O) failure to product attachments not provided by the manufacturer or included in the original sale;

  • Overbuilds Sprint will not provide non-discriminatory access to FTTH Loop or FTTC Loop on an unbundled basis when Sprint has deployed a FTTH Loop or FTTC Loop parallel to, or in replacement of, an existing loop facility, except that:

  • Dewatering 4.7.1 Where a part of a site is affected by surface water following a period of rain, thus rendering some areas unsafe for productive work, consistent with the Employer’s obligations under the OH&S Act, all non- trades employees shall assist in ‘dewatering’ their own work site or area if it is so affected. Such work to be paid at single time rates. Productive work will continue in areas not so affected.

  • Load Shedding The Distributor may carry out Load Shedding in the following circumstances:

  • System Logging The system must maintain an automated audit trail which can 20 identify the user or system process which initiates a request for PHI COUNTY discloses to 21 CONTRACTOR or CONTRACTOR creates, receives, maintains, or transmits on behalf of COUNTY, 22 or which alters such PHI. The audit trail must be date and time stamped, must log both successful and 23 failed accesses, must be read only, and must be restricted to authorized users. If such PHI is stored in a 24 database, database logging functionality must be enabled. Audit trail data must be archived for at least 3 25 years after occurrence.

  • FABRICATION Making up data or results and recording or reporting them.

  • Carrier Lines All Participants acknowledge that the Transaction of Message Content between Participants is to be provided over various facilities and communications lines, and information shall be transmitted over local exchange and Internet backbone carrier lines and through routers, switches, and other devices (collectively, “carrier lines”) owned, maintained, and serviced by third-party carriers, utilities, and Internet service providers, all of which may be beyond the Participants’ control. Provided a Participant uses reasonable security measures, no less stringent than those directives, instructions, and specifications contained in this Agreement, the Performance and Service Specifications, and the Operating Policies and Procedures, the Participants assume no liability for or relating to the integrity, privacy, security, confidentiality, or use of any information while it is transmitted over those carrier lines, which are beyond the Participants’ control, or any delay, failure, interruption, interception, loss, transmission, or corruption of any Message Content or other information attributable to transmission over those carrier lines which are beyond the Participants’ control. Use of the carrier lines is solely at the Participants’ risk and is subject to all Applicable Law.

  • Firefighters Any truck with an inoperative aerial ladder shall be regularly and routinely staffed with one (1) officer and five (5) firefighters for the period of time that the aerial ladder is inoperative, or until such time as the truck with the inoperative aerial ladder is replaced with a truck with an operative aerial ladder. At 0800 and 2000 hours, all trucks shall be staffed with one (1) officer and four (4) firefighters, and any truck with an inoperative aerial ladder shall be staffed with one (1) officer and five (5) firefighters.

  • Television Equipment Recycling Program If this Contract is for the purchase or lease of covered television equipment, then Contractor certifies that it is compliance with Subchapter Z, Chapter 361 of the Texas Health and Safety Code related to the Television Equipment Recycling Program.

  • Safety Glasses 10.3.1 Where a teacher is considered to be working in an “eye danger” area, the teacher shall receive a personal issue of standard neutral safety glasses which shall remain the property of the employer.

Time is Money Join Law Insider Premium to draft better contracts faster.