STRUCTURAL STEELWORK a. All structural steelwork shall comply with the Ministry of Roads, Public Works and Housing “Structural Steelwork Specification (1973) and shall be executed by an approved Sub-contractor.
STRUCTURAL STEELWORK. All damaged paint areas are to be repaired in accordance with the original specification after completion of erection All paint to structural steelwork is to be sourced from an approved paint manufacturer and to be applied in accordance with the manufacturers specifications All bolts are to be degreased prior to erection and painted after erection Clean brickwork thoroughly and seal face brickwork with brick dressing 1 On external walls m2 1 969 Clean, prepare and apply one coat professional gypsum and plaster primer or similar approved and two coats Plascon low sheen pure acrylic paint. 2 On internal walls m2 5 723 Two coats interior quality PVA acrylic paint on work in bad condition 3 On slab ceiling m2 1 764 Xxxx No. 13 Paintwork Prepared by Takgalang Consulting Clean entire surface with Polycell Sugar Soap using bristle brooms or brushes or Scotch Brite pads to remove all surface contaminants, rinse with tap water and allow to dry. Remove loose and flaky paint and sand surface to a firm edge, feather edges and dust off. Xxxxx paper any rust areas to bright metal and remove dust. Spot prime bare areas with Plascon Coastcote Primer Red Oxide (SNK 2) and allow 1 hour to dry. Finish with two coats of Nuroof Acrylic Roof Paint (TRP) or Dulux Roofguard (Code: D8) with an Clean, prepare and seal roof covering, Spot prime bare areas with Plascon Coastcote Primer Red Oxide (SNK 2), Finish with two coats of Nuroof Acrylic Roof Paint (TRP) or Dulux Roofguard (Code: D8) 4 On corrugated roof sheeting. m2 513 Prepare, sand down and apply Plascon Rust Remover (PR1). Remove rust conerter with clean water and apply either Plascon Universal Unsercoat (UC1) or Professional Undercoat (PU800) to bare and repaired areas. Apply two coats Plascon Professional Gloss enamel (PSB 1000). Colour: White 5 On windows with burglar bars m2 249 6 On door frames m2 199 7 On gutters, down pipes n.e. 300mm girth m 340 Xxxx No. 13 Paintwork Prepared by Takgalang Consulting Prepare and apply one coat universal undercoat and two coats acrylic emulsion paint 8 On doors m2 895 9 On shelves m2 720 Carried to Collection Xxxx No. 13 Paintwork Prepared by Takgalang Consulting Section No. 3
STRUCTURAL STEELWORK. All work is required to be in accordance with the latest edition of SANS 2001-CS1
STRUCTURAL STEELWORK. Unit Quantity Rate
STRUCTURAL STEELWORK. (CPAP WORK GROUP NO. 134 UNLESS OTHERWISE STATED) Key: Location Description: Un/A Unallocated Descriptions of bolts shall be deemed to include nuts and washers Descriptions of L-shaped and U-shaped anchor bolts shall be deemed to include bending, threading, nuts and washers and embedding in concrete Descriptions of expansion anchors and bolts and chemical anchors and bolts shall be deemed to include nuts, washers and mortices in brickwork or concrete Welded beams in single lengths with flat bearer and connection plates, bolted to steel 1 200 x 200 x 10mm square hollow sections t 2 350 x 350 x 20mm base plates t
STRUCTURAL STEELWORK. Materials and workmanship shall conform with the requirements of B.S. 449. Steel frames, trusses and purlins shall be carried out by a Nominated Sub-Contractor.
STRUCTURAL STEELWORK. NOTE The Tenderer is advised to refer to the Trade Preambles before pricing these bills of quantities Descriptions of bolts shall be deemed to include nuts and washers Descriptions of L-shaped and U-shaped anchor bolts shall be deemed to include bending, threading, nuts and washers and embedding in concrete Descriptions of expansion anchors and bolts and chemical anchors and bolts shall be deemed to include nuts, washers and mortices in brickwork or concrete Steelwork described as 'galvanised' shall be galvanised by means of the hot-dip process after fabrication. Where welding on site is unavoidable, such welded joints shall be cleaned down and cold galvanised to approval Rates to include for procurement, three (3) copies of workshop drawings where required, fabrication with welding as indicated on drawings, holes, wire brushing, delivery and erection on site complete Correction of shop drawings shall not constitute a change in scope of work unless the contractor notifies the principal agent in writing within seven (7) calender days and shall not proceed with fabrication until so authorised by the principal agent
STRUCTURAL STEELWORK. NOTE: Tenderers are advised to study the "Model Preambles for Trades" before pricing this xxxx
STRUCTURAL STEELWORK. NOTE: Tenderers are advised to study the Model Preambles for Trades and the Project Specification before pricing the bills of quantities. SUPPLEMENTARY PREAMBLES Descriptions Descriptions of bolts shall be deemed to include nuts and washers Descriptions of L-shaped and U-shaped anchor bolts shall be deemed to include bending, threading, nuts and washers and embedding in concrete Descriptions of expansion anchors and bolts and chemical anchors and bolts shall be deemed to include nuts, washers and mortices in brickwork or concrete Where anchor bolts are described as embedded in sides or soffits of concrete it shall be deemed to include holes through formwork
STRUCTURAL STEELWORK. COLLECTION Page No BUILDINGS Bill No. 9 Quantity Rate