Common use of TEST CUBES Clause in Contracts

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 Carried Forward to Summary of Section No. 2 R Section No. 2 SFD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI CONSULTING ENGINEERS Item No SECTION 3 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 Bill No. 3 MASONRY BVI CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 41 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 28 Carried Forward to Summary of Section No. 2 4 R Section No. 2 SFD4 4 MD4 BLOCK Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI MANKGA LERAGA CONSULTING ENGINEERS Item No SECTION 3 4 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 4 MD4 BLOCK Bill No. 3 MASONRY BVI MANKGA LERAGA CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 48 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 12 14 Leave or form 500mm diameter opening in top of floor slab No 5 7 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 39 Carried Forward to Summary of Section No. 2 4 R Section No. 2 SFD4 4 MD6 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI CONSULTING ENGINEERS Item No SECTION 3 4 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 4 MD6 Bill No. 3 MASONRY BVI CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 Carried Forward to Summary of Section No. 2 R Section No. 2 SFD4 FD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI CONSULTING ENGINEERS Item No SECTION 3 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 FD4 Bill No. 3 MASONRY BVI CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 14 Leave or form 500mm diameter opening in top of floor slab No 5 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 Carried Forward to Summary of Section No. 2 4 R Section No. 2 SFD4 4 FD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI CONSULTING ENGINEERS Item No SECTION 3 4 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 4 FD4 Bill No. 3 MASONRY BVI CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc

TEST CUBES. 11 10 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 3 FORMWORK Rough formwork to sides: 12 11 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 22 Permanent formwork to soffits: 13 12 Slabs propped up not exceeding 1.5m high m2 8 14 2 13 Leave or form 500mm diameter opening in top of floor slab No 5 4 REINFORCEMENT Mesh Reinforcement (measure nett): 15 ) 14 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 13 Carried Forward to Summary of Section No. 2 3 R Section No. 2 SFD4 Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI CONSULTING ENGINEERS Item No SECTION NO. 3 Quantity Rate BILL NO.3 NO. 3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: descriptions Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: etc Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: bricks Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 Bill No. 3 MASONRY BVI CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etcR

TEST CUBES. 11 Allow for preparing a set of three test cubes each size 150x150x150mm, sending them to an approved testing laboratory for testing and paying all charges in connection therewith. No 24 FORMWORK Rough formwork to sides: 12 Edges, risers, ends and reveals not exceeding 300mm high or wide m 37 44 Permanent formwork to soffits: 13 Slabs propped up not exceeding 1.5m high m2 8 11 14 Leave or form 500mm diameter opening in top of floor slab No 5 6 REINFORCEMENT Mesh Reinforcement (measure nett): 15 Mesh ref. No. 395 fabric reinforcement fixed horizontal in surface beds m2 21 32 Carried Forward to Summary of Section No. 2 3 R Section No. 2 SFD4 3 MD4 BLOCK Bill No. 2 CONCRETE,FORMWORK AND REINFORCEMENT BVI MANKGA LERAGA CONSULTING ENGINEERS Item No SECTION 3 Quantity Rate BILL NO.3 BRICKWORK SUPPLEMENTARY PREAMBLES For preambles see "Specifications of materials and methods to be used - PW 371" BRICKWORK Sizes in descriptions: Where sizes in descriptions are given in brick units, "one brick" shall represent the length and "half brick" the width of a brick Hollow walls etc.: Descriptions of hollow walls shall be deemed to include leaving every fifth perpend of the bottom course of the external skin open as a weep hole. Walls in two skins described as "bagged and sealed" shall be deemed to include having the outer face of the inner skin bagged with 1:6 cement and sand mixture and sealed with two coats "Brixeal" bitumen emulsion waterproofing coating. User note: The above preamble generally applies for works in hot and humid coastal areas Face bricks: Bricks shall be ordered timeously to obtain uniformity in size and colour Carried Forward R Section No. 2 SFD4 3 MD4 BLOCK Bill No. 3 MASONRY BVI MANKGA LERAGA CONSULTING ENGINEERS Amount Brought Forward R Pointing: Descriptions of recessed pointing to fair face brickwork and face brickwork shall be deemed to include square recessed, hollow recessed, weathered pointing, etc