Test procedure The engine speed shall be gradually increased from idle to the target engine speed, not exceeding the tolerance band of ±3 per cent of the target engine speed, and held constant. Then the throttle control shall be rapidly released and the engine speed shall be returned to idle. The sound pressure level shall be measured during a period of operation consisting of a maintaining constant engine speed of 1 second and throughout the entire deceleration period. The maximum sound level meter reading during this period of operation, mathematically rounded to the first decimal place, is taken as the test value.
Test Procedures For an Asset Review, the Asset Representations Reviewer will perform for each Asset Review Receivable the procedures listed under “Procedures to be Performed” in Schedule A for each representation and warranty (each, a “Test”), using the Asset Review Materials listed for each such Test in Schedule A. For each Test and Asset Review Receivable, the Asset Representations Reviewer will determine if the Test has been satisfied (a “Test Pass”) or if the Test has not been satisfied (a “Test Fail”).
Completion of Review for Certain Subject Receivables Following the delivery of the list of the Subject Receivables and before the delivery of the Review Report by the Asset Representations Reviewer, the Servicer may notify the Asset Representations Reviewer if a Subject Receivable is paid in full by the Obligor or purchased from the Issuer by the Sponsor, the Depositor or the Servicer according to the applicable Basic Document. On receipt of notice, the Asset Representations Reviewer will immediately terminate all Tests of such Receivables and the Review of such Receivables will be considered complete (a “Test Complete”). In this case, the Review Report will indicate a Test Complete for the Receivables and the related reason.
Purpose; Incorporation by Reference of Auction Procedures and Settlement Procedures (a) On each Auction Date, the provisions of the Auction Procedures will be followed by the Auction Agent for the purpose of determining the Applicable Rate for the of APS, for the next Dividend Period therefor. Each periodic operation of such procedures is hereinafter referred to as an "Auction."
(b) All of the provisions contained in the Auction Procedures and the Settlement Procedures are incorporated herein by reference in their entirety and shall be deemed to be a part of this Agreement to the same extent as if such provisions were set forth fully herein.
(c) BD agrees to act as, and assumes the obligations of and limitations and restrictions placed upon, a Broker-Dealer under this Agreement. BD understands that other Persons meeting the requirements specified in the definition of "Broker-Dealer" contained in Paragraph 10 of Article VII of the Amended By-laws may execute a Broker-Dealer Agreement and participate as Broker-Dealers in Auctions.
(d) BD and other Broker-Dealers may participate in Auctions for their own accounts. However, the Trust, by notice to BD and all other Broker Dealers, may prohibit all Broker-Dealers from submitting Bids in Auctions for their own accounts, provided that Broker-Dealers may continue to submit Hold Orders and Sell Orders.
Conformity Assessment Procedures 1. Each Party shall give positive consideration to accepting the results of conformity assessment procedures of other Parties, even where those procedures differ from its own, provided it is satisfied that those procedures offer an assurance of conformity with applicable technical regulations or standards equivalent to its own procedures.
2. Each Party shall seek to enhance the acceptance of the results of conformity assessment procedures conducted in the territories of other Parties with a view to increasing efficiency, avoiding duplication and ensuring cost effectiveness of the conformity assessments. In this regard, each Party may choose, depending on the situation of the Party and the specific sectors involved, a broad range of approaches. These may include but are not limited to:
(a) recognition by a Party of the results of conformity assessments performed in the territory of another Party;
(b) recognition of co-operative arrangements between accreditation bodies in the territories of the Parties;
(c) mutual recognition of conformity assessment procedures conducted by bodies located in the territory of each Party;
(d) accreditation of conformity assessment bodies in the territory of another Party;
(e) use of existing regional and international multilateral recognition agreements and arrangements;
(f) designating conformity assessment bodies located in the territory of another Party to perform conformity assessment; and
(g) suppliers’ declaration of conformity.
3. Each Party shall exchange information with other Parties on its experience in the development and application of the approaches in Paragraph 2(a) to (g) and other appropriate approaches with a view to facilitating the acceptance of the results of conformity assessment procedures.
4. A Party shall, upon request of another Party, explain its reasons for not accepting the results of any conformity assessment procedure performed in the territory of that other Party.
