Test Procedure means all aspects of engine testing including but not limited to the cycle, preconditioning procedures, equipment specifications, calibrations, calculations and other protocols and specifications needed to measure emissions.
Test Procedure. When the alarm sounds, make your way very quickly, but without running to the nearest fire exit (possibly not main stairway), once outside make your way to the evacuation area outside as marked on the fire information panel in your Room. THIS IS AN IMPORTANT HEALTH & SAFETY ISSUE DISREGARD OF THE EVACUATION TESTS WILL BE TREATED VERY SERIOUSLY BY THE UNIVERSITY. At the initial fire drill completed in the first week, your Hall Student Life Rep, or a member of staff, will check who is present at the evacuation area and when the test is complete you will be able to return to your Rooms. Do not re- enter the building unless advised. Subsequent Fire Alarms will require you to follow exactly the same procedure as carried out in the practice test – on the sound of the fire alarm, you are always expected to vacate the building. Please note that Fire Alarms are tested on a weekly basis. On these occasions, the alarm will sound for approximately 15 seconds and then cease. Should this be the case, you are not required to vacate. Tampering with Fire Safety Equipment in Halls Student(s) who are found to have, for example, discharged a fire extinguisher, interfered with a fire extinguisher, fixing or smoke detector, set off a fire alarm, or tampered with any kind of fire safety equipment will each incur a fine in line with the Student Disciplinary Policy, and a warning letter stating that further incidents of any disciplinary nature may result in the individual(s) being removed from their room. The cost of repairing the equipment will be divided equally between all and a charge will be madeof £50 for additional time incurred in the handling of the incident. In agreeing to the terms and conditions outlined in this document you are agreeing to adhere to the procedure outlined above. Please ensure that you understand this procedure. Upon occupation of your Room please familiarise yourself with the Hall/House of Residence, the location of fire exits and the evacuation procedure.
Test Procedure. 8: Time between successful positioning fixes For: KPI_012: Time between successful positioning fixes General definition of test scenario: This test refers to the duration of time interval between two consecutive successful positioning fixes, thus defining the estimation of position estimation uncertainty at the certain vehicle velocity due to the age of position estimates. Preconditions: 1) IVS A GPS receiver is required. Utilization of a SBAS / EGNOS- enabled or combined GPS+EGNOS / GLONASS receiver is an advantage. Access to NMEA data stream using a dedicated application, or access to internal NMEA stream log is needed.
Examples of Test Procedure in a sentence
The battery bank shall be fully operational and in good working condition before the Test Procedure execution.
The ESS shall be in working condition before executing the Test Procedure; provided, if the test is being conducted in connection with making a Warranty claim (including pursuant to the Capacity Performance Guarantee), the Supplier shall be required to put the ESS in workable condition prior to the Buyer conducting the test and submitting a Warranty Claim.
The Bank shall be fully operational and in good working condition before the Test Procedure execution.
Test Conditions (at Bank level) Parameter Value Unit Maximum Charge Power 30% of the XXXX rated power kW Maximum Discharge Power 30% of the XXXX rated power kW Maximum State of Charge (“SOC”) 100% (for capacity test only) % Minimum SOC 0% (for capacity test only) % Minimum Rest Period 30 min Temperature Range 23±5 ℃ Minimum Metering Accuracy 0.5 % Test Procedure.
The Test Procedure will not operate any components of the Product outside of the safe recommended ranges of the Supplier or in any way to violate the Product Warranty or damage the Product or Product Components.
More Definitions of Test Procedure
Test Procedure. The driver manually initiates an eCall at various positions; in different traffic environments (see Table 4 above). At several selected locations along the road, representative of the area and with possible low GPS coverage, the driver stops the vehicle at the roadside and manually activates eCall. Log files are stored in the vehicle and in the PSAP and both the driver and the PSAP operator complete a subjective questionnaire containing a standardized value scale for the evaluation after the end of each eCall.
Test Procedure means the preconditioning sequence and smoke opacity measurement processes for determining compliance with section 2182.
Test Procedure means the smoke meter test procedure as specified in section 2193(c).
Test Procedure. Either tightly clamp or thermite weld current wire connections to the
Test Procedure. To check sensitivity an anodized aluminium plate is coated with the respective amounts of analyte. To cover the aluminium plate with the said analyte amounts, aqueous solutions of the respective analyte are applied and dried. The amount of analyte is determined by volume and concentration of the applied analyte solutions. Examination of the respective Drugwipe has to be performed at room temperature (20(degree)C - 25(degree)C) in accordance with the instruction sheet. A positive result is indicated by a red colour developing within one (!) minute in the detection zone. In dependance of the concentration present the colour changes between cream white and red. /s/ [ILLEGIBLE] SECURETEC [GRAPHIC OMITTED] Sicherheitstechnologie und Gefahrstoffdetektion GmBH Annex F2 Product-specifications, Demands for transport and stocking -------------------------------------------------------------------------------- Storage conditions: Each Drugwipe kit is packed individually to ensure maximum stability and performance. Performance of Drugwipe can only be guaranteed up to the date for best usage printed on each pack, - if each Drugwipe kit is stored in the original packaging, - at a temperature between +15(degree)C and +25(degree)C (between +59(degree)F and +77(degree)F)
Test Procedure means Supplier’s standard testing for its Product prior to shipment, or specific testing for Product that the parties agree to in writing.
Test Procedure means a series of processes and procedural steps to be taken by Tesna for its provision of the Services, including wafer/final test procedure either to be provided by PixelPlus to Tesna or to be determined by the parties upon mutual consultation. Such Test Procedure shall be communicated and confirmed by the test document.