State of California Public Liability and Workers’ Compensation Program A. The Judicial Council has elected to be self-insured for its motor vehicle, aircraft liability and general liability exposures. B. The Judicial Council administers workers’ compensation benefits for its employees through a Third Party agreement.
Power Factor Design Criteria (Reactive Power A wind generating plant shall maintain a power factor within the range of 0.95 leading to 0.95 lagging, measured at the Point of Interconnection as defined in this LGIA, if the ISO’s System Reliability Impact Study shows that such a requirement is necessary to ensure safety or reliability. The power factor range standards can be met using, for example without limitation, power electronics designed to supply this level of reactive capability (taking into account any limitations due to voltage level, real power output, etc.) or fixed and switched capacitors if agreed to by the Connecting Transmission Owner for the Transmission District to which the wind generating plant will be interconnected, or a combination of the two. The Developer shall not disable power factor equipment while the wind plant is in operation. Wind plants shall also be able to provide sufficient dynamic voltage support in lieu of the power system stabilizer and automatic voltage regulation at the generator excitation system if the System Reliability Impact Study shows this to be required for system safety or reliability.
Benefit to Citizens of Xxxxxxx County The safety of the citizens of Xxxxxxx County is enhanced through this Agreement, which promotes safe boating conditions and reduces costs associated with patrols of recreational waterways.
LANCASTER COUNTY, NEBRASKA Contract Approved as to Form:
California Independent System Operator Corporation a California nonprofit public benefit corporation having a principal executive office located at such place in the State of California as the ISO Governing Board may from time to time designate, initially 000 Xxxx Xxxxxx Xxxx, Xxxxxx, Xxxxxxxxxx 00000 (the “ISO”). The ISO Metered Entity and the ISO are hereinafter referred to as the “Parties”.
Synopsis and Benefit to Xxxxxxx County The Agreement continues the contractual relationship between the Oregon State Marine Board and Xxxxxxx County through its Sheriff’s Office. The Sheriff’s Office will be reimbursed for marine law enforcement patrols, boater education, and boat inspections conducted throughout the County.
Wyoming CANCELLATION section is amended as follows: A ten percent (10%) penalty per month shall be applied to refunds not paid or credited within forty-five (45) days of receipt of returned Service Agreement. ARBITRATION section of this Agreement is removed.
Joint Occupational Health and Safety Committee The Employer and the Union recognize the role of the joint Occupational Health and Safety Committee in promoting a safe and healthful workplace. The parties agree that a Joint Occupational Health and Safety Committee shall be established for each Employer covered by this Collective Agreement. The Committee shall govern itself in accordance with the provisions of the Industrial Health and Safety Regulations made pursuant to the Workers’ Compensation Act. The Committee shall be as between the Employer and the Union, with equal representation, and with each party appointing its own representatives. Representatives of the Union shall be chosen by the Union membership or appointed by the Union. All minutes of the meetings of the Joint Occupational Health & Safety Committee will be recorded in a mutually agreeable format and will be sent to the Union. The Union further agrees to actively pursue with the other Health Care Unions a Joint Union Committee for the purposes of this Article. The Employer agrees to provide or cause to be provided to Employer members of the Joint Occupational Health and Safety Committee adequate training and orientation to the duties and responsibilities of committee members to allow the incumbents to fulfil those duties competently. The Union agrees to provide or cause to be provided to Union members of the Joint Occupational Health and Safety Committee adequate training and orientation to the duties and responsibilities of committee members to allow the incumbents to fulfil those duties competently. Such training and orientation shall take place within six (6) months of taking office.
AT&T-12STATE acknowledges that CLEC may have an embedded base of one-way trunks ordered and installed prior to the Effective Date of this Agreement that were used for termination of CLEC’s Section 251(b)(5)/IntraLATA Toll Traffic to AT&T-12STATE (Embedded Base). To the extent that CLEC has such an Embedded Base, CLEC shall only augment trunk groups in the Embedded Base with the mutual agreement of the Parties. CLEC shall not order any new one-way trunk groups following the Effective Date of this Agreement. Moreover, the Parties agree that the Embedded Base will be converted to two-way trunk groups under the following circumstances: 4.2.1.1 With reasonable notification from AT&T-12STATE and upon AT&T-12STATE’s request, CLEC shall convert all of its Embedded Base to two-way trunks. 4.2.1.2 At any time an Embedded Base trunk group (either originating or terminating) requires augmentation, AT&T-12STATE can require the associated originating and terminating trunks to be converted to a single two-way trunk group prior to the augmentation. 4.2.1.3 When any network changes are to be performed on a project basis (i.e., central office conversions, tandem re-homes, etc.), upon request and reasonable notice by AT&T-12STATE, CLEC will convert all of its Embedded Base affected by the project within the intervals and due dates required by the project parameters. 4.2.1.4 In addition to the foregoing, CLEC may choose, at any time, to convert its Embedded Base to two-way trunk groups. 4.2.1.5 The Parties will coordinate any trunk group migration, trunk group prioritization and implementation schedule. AT&T-12STATE agrees to develop a cutover plan within thirty (30) days of notification to CLEC of the need to convert pursuant to Section 4.2.1.1 above and Section 4.2.1.3 above.
Reactive Power and Primary Frequency Response 9.6.1 Power Factor Design Criteria
