Units Note. Output Optical Power (50/125 μm fiber, NA=0.20) (62.5/125μm fiber, NA=0.275) Pout −9 --- -3 dBm Extinction Ratio ER 6 --- --- dB Optical Modulation Amplitude @4.25Gb/s OMA 247 uW Optical Modulation Amplitude @2.125Gb/s OMA 196 uW Optical Modulation Amplitude @1.0625Gb/s OMA 156 uW Center Wavelength λC 830 850 860 nm Spectral Width (RMS) Δλ --- --- 0.85 nm Relative Intensity Noise RIN --- --- -118 dB/Hz Output Eye Compliant with IEEE802.3z and fiber channel 4x Max. Pout TX-DISABLE Asserted XXXX --- --- −35 dBm Differential Input Voltage VDIFF 0.35 --- 2.0 V Transmit Fault Output-Low TX_FAULTL 0 --- 0.5 V Transmit Fault Output-High TX_FAULTH 2.4 --- Vcc V TX_DISABLE Assert Time t_off --- --- 10 μs TX_DISABLE Negate Time t_on --- --- 1 ms Time to initialize include reset of TX_FAULT t_init --- --- 300 ms TX_FAULT from fault to assertion t_fault --- --- 100 μs TX_DISABLE time to start reset t_reset 10 --- --- μs Vcc = 3.1 V to 3.5 V, TC = -10 °C to 70 °C (-40 °C to 85 °C)
Units Note. Optical Input Power-maximum PIN 0 --- --- dBm PIN --- --- −18 dBm Note 2 Receiver Sensitivity (@4.25GBps) PIN 0.029 dBm Note 1 PIN --- --- −21 dBm Note 3 Receiver Sensitivity (@2.1.25GBps/1.25/1.0625GBps) PIN 0.015 dBm Note 1 Operating Center Wavelength λC 1260 --- 1600 nm Optical Return Loss ORL 12 --- --- dB Signal Detect-Asserted PA -20 --- --- dBm Signal Detect-Deasserted PD --- --- -30 dBm Differential Output Voltage VDIFF 0.5 --- 1.2 V Receiver Loss of Signal Output Voltage-Low RX_LOSL 0 --- 0.5 V Receiver Loss of Signal Output Voltage-High RX_LOSH 2.4 --- VCC V Receiver Loss of Signal Assert Time (off to on) tA,RX_LOS --- --- 100 μs Receiver Loss of Signal Assert Time (on to off) tD,RX_LOS --- --- 100 μs Note1: Value in OMA. Measured with PRBS 27-1 at BER=10-12 Note2: Represents sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 13 dB (for example, at 6.0dB incoming extinction ratio, an OMA of 0.029 mW corresponds to -16.1 dBm sensitivity). Measured with PRBS 27-1 atBER=10-12 Note3: Represents sensitivity based on OMA spec, as corrected to incoming Extinction Ratio of 13 dB (for example, at 6dB incoming extinction ratio, an OMA of 0.015 mW corresponds to -19 dBm sensitivity). Measured with PRBS 27-1 at BER=10-12 ELECTRICAL SUBASSEMBLY DATA DATA/ LD Driver & Fault Sense LASER TX_DISABLE TX_FAULT (0) (1)
Units Note. Output Optical Power 9/125 μm fiber Pout -4 --- +1 dBm Center Wavelength λC 1530 1550 1570 nm Spectral Width (-20dB) Δλ --- --- 1 nm Relative Intensity Noise RIN --- --- -118 dB/Hz Output Eye Compliant with IEEE802.3z and fiber channel 4x Max. Pout TX-DISABLE Asserted XXXX --- --- −35 dBm Differential Input Voltage VDIFF 0.35 --- 2.0 V Transmit Fault Output-Low TX_FAULTL 0 --- 0.5 V Transmit Fault Output-High TX_FAULTH 2.4 --- Vcc V TX_DISABLE Assert Time t_off --- --- 10 μs Time to initialize include reset of TX_FAULT t_init --- --- 300 ms TX_FAULT from fault to assertion t_fault --- --- 100 μs TX_DISABLE time to start reset t_reset 10 --- --- μs Vcc = 3.1 V to 3.5 V, TC = -10 °C to 70 °C (-40 °C to 85 °C)
Units Note. Output Optical Power 9/125 μm fiber Pout −8 --- -2 dBm Average Extinction Ratio ER 9 --- --- dB Center Wavelength λC 1270 1310 1355 nm Rise/Fall Time, (20−80%) Tr, f --- --- 260 ps Relative Intensity Noise RIN --- --- -120 dB/Hz Total Jitter TJ --- --- 227 ps Output Eye Compliant with IEEE802.3z Max. Pout TX-DISABLE Asserted XXXX --- --- −45 dBm Differential Input Voltage VDIFF 0.4 --- 2.0 V Vcc = 3.1 V to 3.5 V, TC = 0 °C to 70 °C (-40 °C to 85 °C)
Units Note. Storage Temperature TS −40 85 °C Supply Voltage Vcc −0.5 4.0 V Input Voltage VIN −0.5 Vcc V Output Current Io --- 50 mA Operating Current IOP --- 400 mA Recommended Operating Conditions
