Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Method of Measurement All linear and area measurements under this Agreement are measured on the horizontal plane, unless specified otherwise in an attached Schedule.
Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.
Usage Measurement Usage measurement for calls shall begin when answer supervision or equivalent Signaling System 7 (SS7) message is received from the terminating office and shall end at the time of call disconnect by the calling or called subscriber, whichever occurs first.
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C. 1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Settlement Method For any Option, Net Share Settlement; provided that if the Relevant Settlement Method set forth below for such Option is not Net Share Settlement, then the Settlement Method for such Option shall be such Relevant Settlement Method, but only if Counterparty shall have notified Dealer of the Relevant Settlement Method in the Notice of Final Settlement Method for such Option.
Procurement Method Quality-Based Selection (b) Selection under a Fixed Budget
Payment Methods A. Except as otherwise provided by this Contract, the payment method will be one or more of the following:
Settlement Method Election Physical Settlement, Cash Settlement, or Net Share Settlement, at the election of Counterparty as set forth in a Settlement Notice that satisfies the Settlement Notice Requirements; provided that Physical Settlement shall apply (i) if no Settlement Method is validly selected, (ii) with respect to any Settlement Shares in respect of which Dealer is unable, in good faith and in its commercially reasonable discretion, to unwind its commercially reasonable hedge by the end of the Unwind Period (taking into account any Additional Transactions with overlapping “Unwind Periods” (as defined in the applicable Additional Confirmations)) (A) in a manner that, in the reasonable discretion of Dealer, based on advice of counsel, is consistent with the requirements for qualifying for the safe harbor provided by Rule 10b-18 under the Exchange Act (“Rule 10b-18”) or (B) in its commercially reasonable judgment, due to the occurrence of five or more Disrupted Days or to the lack of sufficient liquidity in the Shares on any Exchange Business Day during the Unwind Period, (iii) to any Termination Settlement Date (as defined under “Termination Settlement” in Paragraph 7(g) below) and (iv) if the Final Date is a Settlement Date other than as the result of a valid Settlement Notice, in respect of such Settlement Date; provided, further, that, if Physical Settlement applies under clause (ii) immediately above, Dealer shall provide written notice to Counterparty at least two Scheduled Trading Days prior to the applicable Settlement Date.
Source of Measure Law No. 20 of 2008 Concerning Micro, Small and Medium Enterprises - Law No. 25 of 1992 Concerning Cooperatives
