Volumetric Flow Rate Tests Sample Clauses

Volumetric Flow Rate Tests. The volumetric flowrate of the exhaust gases, at the * will be determined using EPA Methods 1 through 4. The required number of traverse points, in accordance with EPA Method 1, will be used. * measurements will be taken at each traverse point during each test run. Duct temperature measurements will also be taken at each traverse point using a Type-K thermocouple and digital temperature readout. The duct static pressure will also be measured during each test run. Methods to be considered are pitot tube and manometer set up and/or anemometer readings or other methods appropriate for this high temperature gas. The MHF offgas moisture content will be determined from the moisture catch of the constant rate sampling train during the emissions testing in accordance with EPA Method 4. A minimum sample volume of thirty (30) cubic feet will be collected during each of the *-hour periods of the performance test. The moisture content of the flue gas will be calculated as the ratio of the moisture catch corrected to standard conditions to the sum of the dry sample volume and the moisture catch, both corrected to standard conditions.
AutoNDA by SimpleDocs

Related to Volumetric Flow Rate Tests

  • Performance Tests Contractor shall perform Performance Tests in accordance with Section 11.2 of the Agreement and Attachment S.

  • Maximum Leverage Ratio As of the last day of each fiscal quarter, the Borrower shall not permit the ratio (the "Leverage Ratio") of (i) Consolidated Funded Indebtedness to (ii) EBITDA of the Borrower and its Subsidiaries, as at the end of and for the period of four consecutive fiscal quarters ending on such day, to be greater than (i) 2.00 to 1.00.

  • Total Net Leverage Ratio The Borrower will not permit the Total Net Leverage Ratio as of the end of any Fiscal Quarter to exceed 3.50 to 1.00.

  • Cash Flow Leverage Ratio The Borrower will not permit the Cash Flow Leverage Ratio on the last day of any fiscal quarter to exceed 3.50 to 1.00.

  • Maximum Total Leverage Ratio Permit the Total Leverage Ratio as of the end of any fiscal quarter ending on or after September 30, 2006, to be greater than the ratio set forth below opposite the fiscal quarter end: Fiscal Quarter Ending Ratio on or prior to December 31, 2008 6.50 to 1.0 thereafter but on or prior to December 31, 2010 6.00 to 1.0 after December 31, 2010 5.50 to 1.0

  • Maximum Senior Leverage Ratio Borrower and its Subsidiaries on a consolidated basis shall have, at the end of each Fiscal Quarter set forth below, a Senior Leverage Ratio as of the last day of such Fiscal Quarter and for the 12-month period then ended of not more than the following:

  • Maximum Leverage Permit, as of any fiscal quarter end, the ratio of (a) Adjusted Portfolio Equity as of such fiscal quarter end to (b) Funded Debt as of such fiscal quarter end, to be less than 5.00 to 1.00.

  • Measurement All quantities of Products received or delivered by or into truck, rail, or marine vessel shall be measured and determined based upon the meter readings at each Terminal, as reflected by delivery tickets or bills of lading, or if such meters are unavailable, by applicable calibration tables. All quantities of Products received and delivered by pipeline shall be measured and determined based upon the meter readings of the pipeline operator, as reflected by delivery tickets, or if such meters are unavailable, by applicable calibration tables. Deliveries to a Terminal rack at Mandan, Salt Lake City or Wilmington from a Tesoro Refinery shall be deemed to be the same as the corresponding volumes delivered contemporaneously from the Terminal rack. Deliveries by book transfer shall be reflected by entries in the books of TLO. All quantities shall be adjusted to net gallons at 60° F in accordance with ASTM D-1250 Petroleum Measurement Tables, or latest revisions thereof. A barrel shall consist of 42 U.S. gallons and a gallon shall contain 231 cubic inches. Meters and temperature probes shall be calibrated according to applicable API standards. Tesoro shall have the right, at its sole expense, and in accordance with rack location procedure, to independently certify said calibration. Storage tank gauging shall be performed by TLO’s personnel. TLO’s gauging shall be deemed accurate unless challenged by an independent certified xxxxxx. Tesoro may perform joint gauging at its sole expense with TLO’s personnel at the time of delivery or receipt of Product, to verify the amount involved. If Tesoro should request an independent xxxxxx, such xxxxxx must be acceptable to TLO, and such gauging shall be at Tesoro’s sole expense.

  • Minimum Interest Coverage Ratio The Borrowers shall not permit the Interest Coverage Ratio, calculated as of the end of each fiscal quarter for the four fiscal quarters then ended, to be less than 3.50 to 1.00.

  • Net Leverage Ratio Subject to the proviso set forth in Section 10.3, the Company will not permit the Consolidated Net Leverage Ratio at any time during any period of four consecutive fiscal quarters of the Company to be greater than (a) 3.50 to 1.00 or (b) during an Acquisition Holiday Period, 4.00 to 1.00.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!