Aerospace coatings definition

Aerospace coatings means materials that are applied to the surface of an aerospace vehicle or component to form a decorative, protective, or functional solid film, or the solid film itself at a facility that produces, reworks, or repairs in any amount any commercial, civil, or military aerospace vehicle or component.
Sample 1Sample 2Sample 3
Aerospace coatings means materials including but not limited to those specified in the table in Subsection (d)(1)(i) of this rule, which contain more than 20 grams of VOC per liter of coating, as applied, less water and less exempt compounds. Preservative oils and compounds, form release agents not containing solids, and greases and waxes are not aerospace coatings.
Sample 1Sample 2
Aerospace coatings means materials that are applied to the surface of an aerospace vehicle or component to form a decorative, protective, or functional solid
Sample 1Sample 2

Examples of Aerospace coatings in a sentence

  • Aerospace coatings which are utilized for pretreatment, adhesive bonding primers, flight testing, fuel tanks, electric/radiation effects, space vehicles and temporary mechanical maskant/high temperature heat treatment are not subject to the VOC limits of this section.

  • Large appliance coatings.(b) Aerospace coatings; (g) Flat wood paneling coatings; [FR Doc.

  • Aerospace coatings that meet the definitions of the specific coatings in Table II shall meet those allowable coating VOC limits.

  • Aerospace Coatings - Aerospace coatings shall conform toBAAQMD Regulation 8, Rule 29 for VOC content limits.

  • This category applies to areas in which at least 60% of the agricultural area meets at least one of the criteria listed in Annex III (or Table A1.1 in this chapter) of the regulation at the threshold values indicated.

  • Aerospace Coatings - Aerospace coatings shall conform to BAAQMD Regulation 8, Rule 29 for VOC content limits.

  • The following emission limits shall apply to each product category of fac- tory-finished paneling (regardless of the number of coats applied).] [Figure: 30 TAC §115.421(b)(9)][(10) Aerospace coatings.

  • Aerospace coatings that meet the definitions of the specific coatings in Table II shall meet those allowable coating VOC limits.(ii) All other aerospace primers, aerospace topcoats and chemical milling maskants are subject to the general coating VOC limits for aerospace primers, aerospace topcoats and aerospace chemical milling maskants.

  • A contrast-detail analysis is a common technique used to evaluate low-contrast resolution of radiographic images and pro- vides a quantitative evaluation [20].

  • Aerospace coatings are highly specialised coatings supplied to aircraft manufacturers, maintenance companies, airlines etc.

Related to Aerospace coatings

  • Flat coating means a coating that is not defined under any other definition in this section and that registers gloss less than 15 on an 85-degree meter or less than 5 on a 60-degree meter.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Metallic coating means a coating which contains more than five grams of metal particles per liter of coating, as applied. Metal particles are pieces of a pure elemental metal or a combination of elemental metals.

  • Specialty coating means any coating that is manufactured and used for one (1) of the following specialized applications:

  • Biomethane means biogas that meets pipeline quality natural gas standards.

  • Caliper means and refer to a standard trunk diameter measurement for trees. Caliper measurements are taken twelve inches above the finished grade.

  • Tire means a continuous solid or pneumatic rubber covering encircling the wheel of a tractor or other farm machinery or of a vehicle.

  • Roll coating means the application of a coating material to a substrate by means of hard rubber or steel rolls.

  • Oxides of nitrogen means the sum of the volume mixing ratio (ppbv) of nitrogen monoxide (nitric oxide) and nitrogen dioxide expressed in units of mass concentration of nitrogen dioxide (µg/m3);

  • Automotive windshield washer fluid means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

  • Topcoat means a coating that is applied over a primer on an aerospace vehicle or component for appearance, identification, camouflage, or protection. Topcoats that are defined as specialty coatings are not included under this definition.

  • Seaplane means an aeroplane capable normally of taking off from and alighting solely on water;

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • aeroplane means a power-driven heavier-than-air aircraft, deriving its lift in flight chiefly from aerodynamic reactions on surfaces which remain fixed under given conditions of flight;

  • Solutions means Products and Services provided under this “CPE Products & Services; Professional Services” Section.

  • Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, and stains.

  • Industrial maintenance coating means a high performance architectural coating, including primers, sealers, undercoaters, intermediate coats, and topcoats formulated for application to substrates, including floors, exposed to one or more of the following extreme environmental conditions listed below and labeled “For industrial use only;” “For professional use only;” “Not for residential use;” or “Not intended for residential use.”

  • Homemaker services means the professionally directed or supervised simple household maintenance or management services provided by trained homemakers or individuals to families in their own homes.

  • Basecoat means a coat of colored material, usually opaque, that is applied before graining inks, glazing coats, or other opaque finishing materials and is usually topcoated for protection.

  • Floor coating means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces which may be subject to foot traffic.

  • cannabis resin means the separated resin, whether crude or purified, obtained from any plant of the genus Cannabis;

  • Aerosol coating product means a pressurized coating product containing pigments or resins that dispenses product ingredients by means of a propellant, and is packaged in a disposable can for hand-held application, or for use in specialized equipment for ground traffic/marking applications.

  • Pretreatment coating means a coating which contains no more than 12% solids by weight, and at least 0.5% acid by weight, is used to provide surface etching, and is applied directly to metal surfaces to provide corrosion resistance, adhesion, and ease of stripping.

  • Nuclear coating means a protective coating formulated and recommended to seal porous surfaces such as steel (or concrete) that otherwise would be subject to intrusions by radioactive materials. These coatings must be resistant to long-term (service life) cumulative radiation exposure [ASTM method D4082], relatively easy to decontaminate, and resistant to various chemicals to which the coatings are likely to be exposed [ASTM method D3912].

  • Faux finishing coating means a coating labeled and formulated as a stain or a glaze to create artistic effects including, but not limited to, dirt, old age, smoke damage, and simulated marble and wood grain.

  • Cannabis means all parts of the plant Cannabis sativa Linnaeus, Cannabis indica, or Cannabis ruderalis, whether growing or not; the seeds thereof; the resin, whether crude or purified, extracted from any part of the plant; and every compound, manufacture, salt, derivative, mixture, or preparation of the plant, its seeds, or resin. “Cannabis” also means the separated resin, whether crude or purified, obtained from cannabis. “Cannabis” does not include the mature stalks of the plant, fiber produced from the stalks, oil or cake made from the seeds of the plant, any other compound, manufacture, salt, derivative, mixture, or preparation of the mature stalks (except the resin extracted therefrom), fiber, oil, or cake, or the sterilized seed of the plant which is incapable of germination. For the purpose of this division, “cannabis” does not mean “industrial hemp” as defined by Section 11018.5 of the Health and Safety Code. Cannabis and the term “marijuana” may be used interchangeably.