ASTM D93 definition

ASTM D93 means ASTM’s Standard D93, entitled “Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester,” as amended and supplemented.

Examples of ASTM D93 in a sentence

  • ASTM D93*** * Utilize the current and most applicable SW-846 method to test for the target analyte and the limitation level.

  • It should be enable to distillate fuels according to ASTM D93 A+B+C,ISO 2719 A+B+C, JISK 2265-3 A+B, IP 34 A+B, GOST REN ISO 2719.

  • The following fuel properties were measured: acid value (ASTM D664), kinematic viscosity (ASTM D4052), cold flow plugging point (ASTM D6371), iodine value (EN 14111), cloud point (ASTM D2500), oxidative stability (EN 14112) and flash point (ASTM D93).

  • Similar experimental checks are carried out for viscosity (ASTM D455), freeze point (ASTM D5972), flash point (ASTM D93), and so on.

  • Importer shall advise the flashpoint of the tendered dispersant, as determined by the Pensky Marten closed cup method (ASTM D93, IP 34, BS 2834).

  • Depending on the test method used, the values given are either Tag closed cup (C.C.) (ASTM D56) or Cleveland open cup (O.C.) (ASTM D93).

  • FLAMMABLE PROPERTIES:FLASH POINT: 140 oF (>60 oC) (minimum) ASTM D-93 AUTOIGNITION TEMPERATURE: > 505 oF (>263 oC)OSHA/NFPA FLAMMABILITY CLASS: IIIA (COMBUSTIBLE) LOWER EXPLOSIVE LIMIT (%): N/DUPPER EXPLOSIVE LIMIT (%): N/DFIRE AND EXPLOSION HAZARDSVapors may be ignited rapidly when exposed to heat, spark, open flame or other source of ignition.

  • Flash Point (Method Used): >200°F / >93.3°C (ASTM D-93 Pensky-Martens Closed Cup).Flammable Properties:Upper Flammable Limit: N/A Lower Flammable Limit: N/AExplosive Limits: UEL: N/A LEL: N/AAuto-ignition Temperature: N/AHazardous Combustion Products: None known.Explosion Data (Sensitivity to Mechanical Impact): N/AExplosion Data (Sensitivity to Static Discharge): N/AExtinguishing Media:Suitable: CO2, water, dry chemical or “alcohol” foam.

  • EXHIBIT A-6 Product: Atmospheric Gas Oil from AVU 146 ------- Target Specification: -------------------- Property Specification Test Method -------- ------------- ----------- Flash Point 165 Degrees F Minimum ASTM D-93 Quantity: Xxxxx Company shall sell and Xxxxx shall purchase the "Xxxxx Company -------- Share" of the total output of this Product.

  • Estimation of kinematic viscosity and flash pointPhysicochemical properties, such as kinematic viscosity and flash point for fuel blends with alumina nanoparticles (10 and 20 ppm) were determined according to ASTM D445 and ASTM D93 regulations.

Related to ASTM D93

  • MI 61-101 means Multilateral Instrument 61-101 – Protection of Minority Security Holders in Special Transactions;

  • NI 81-102 means National Instrument 81-102 – Investment Funds.

  • NI 51-102 means National Instrument 51-102 – Continuous Disclosure Obligations;

  • NI 51-101 means National Instrument 51-101 Standards of Disclosure for Oil and Gas Activities;

  • MI 11-102 means Multilateral Instrument 11-102 – Passport System;

  • NI 54-101 means National Instrument 54-101 – Communication with Beneficial Owners of Securities of a Reporting Issuer;

  • Semi-annual (2/Year) sampling frequency means the sampling shall be done during the months of June and December, unless specifically identified otherwise.

  • NI 81-107 means National Instrument 81-107 Independent Review Committee for Investment Funds;

  • NI 58-101 means National Instrument 58-101 Disclosure of Corporate Governance Practices;

  • MI 62-104 means Multilateral Instrument 62-104 — Take-Over Bids and Issuer Bids, as amended or replaced from time to time;

  • NI 81-106 means National Instrument 81-106 Investment Fund Continuous Disclosure;

  • NI 41-101 means National Instrument 41-101 – General Prospectus Requirements;

  • S&P CDO Monitor Test A test that will be satisfied on any date of determination (following receipt, at any time on or after the S&P CDO Monitor Election Date, by the Issuer and the Collateral Administrator of the Class Break-even Default Rates for each S&P CDO Monitor input file (in accordance with the definition of “Class Break-even Default Rate”)) if, after giving effect to a proposed sale or purchase of an additional Collateral Obligation, the Class Default Differential of the Highest Ranking Class of the Proposed Portfolio is positive. The S&P CDO Monitor Test will be considered to be improved if the Class Default Differential of the Proposed Portfolio that is not positive is greater than the corresponding Class Default Differential of the Current Portfolio.

  • NI 62-104 means National Instrument 62-104 – Take-Over Bids and Issuer Bids;

  • Temporary clean coal technology demonstration project means a clean coal technology demonstration project that is operated for a period of five years or less and that complies with the SIP and other requirements necessary to attain and maintain the national ambient air quality standards during the project and after the project is terminated.

  • NI 31-103 means National Instrument 31-103 Registration Requirements, Exemptions and Ongoing Registrant Obligations;

  • Semi-annual (2/Year) sampling frequency means the sampling shall be done during the months of June and December, unless specifically identified otherwise.

  • NI 45-106 means National Instrument 45-106 – Prospectus and Registration Exemptions;

  • Modular building manufacturer means a person or corporation who owns or operates a

  • chemical tanker means a ship constructed or adapted and used for the carriage in bulk of any liquid product listed in chapter 17 of the International Bulk Chemical Code;

  • NI 45-102 means National Instrument 45-102 – Resale of Securities;

  • NI 43-101 means National Instrument 43-101 – Standards of Disclosure for Mineral Projects;

  • Clean coal technology demonstration project means a project using funds appropriated under the heading “Department of Energy—Clean Coal Technology,” up to a total amount of $2,500,000,000 for commercial demonstration of clean coal technology, or similar projects funded through appropriations for the Environmental Protection Agency. The federal contribution for a qualifying project shall be at least 20 percent of the total cost of the demonstration project.

  • Yearly (1/Year) sampling frequency means the sampling shall be done in the month of September, unless specifically identified otherwise in the effluent limitations and monitoring requirements table.

  • PM10 means particulate matter with an aerodynamic diameter less than or equal to a nominal 10 micrometers as measured by an EPA reference or equivalent method.

  • NP 11-202 means National Policy 11-202 – Process for Prospectus Reviews in Multiple Jurisdictions;