Calibration error definition

Calibration error means the difference between the gas concentration indicated by the measurement system and the known concentration of the calibration system.
Sample 1Sample 2Sample 3
Calibration error means the difference between the gas concentration indicated by the measurement system and the know concentration of the cali- bration gas.
Sample 1
Calibration error means the percentage difference between the gas concentration measured by the gas analyzer and the known concentration of the calibration gas.
Sample 1Sample 2

Examples of Calibration error in a sentence

  • Carbon monoxide CEMS that use a span value of 10,000 are subject to the same CEMS performance and equipment specifications when oper- ating in the range of 3,000 ppmv to 10,000 ppmv that are provided by Per- formance Specification 4B for other carbon monoxide CEMS, except:(A) Calibration drift must be less than 300 ppmv; and(B) Calibration error must be less than 500 ppmv.(4) Hydrocarbon readings exceeding the span.

  • Calibration error Identify the causes of calibration error and its effect on processes and products.

  • Calibration error for the zero and span calibration gas checks must be less than ± 5 percent of the span calibration gas value before sampling may be conducted.

  • For each reference value, calculate the percentage calibration error based upon in- strument span for daily calibration error tests using the following equation: (Eq. A–5) where, CE = Calibration error as a percentage of the span of the instrument.

  • Calibration error - perform fundamental calibration in Configuration Mode.Poor control response,Non-repeatable flow settings LeakageContamination or damage to valves- return for repair.

  • Calibration error tests are often performed prior to a linearity test or RATA.

  • Carbon monoxide CEMS that use a span value of 10,000 are subject to the same CEMS performance and equipment specifications when operating in the range of 3,000 ppmv to 10,000 ppmv that are provided by Performance Specification 4B for other carbon monoxide CEMS, except:(A) Calibration drift must be less than 300 ppmv; and(B) Calibration error must be less than 500 ppmv.(4) Hydrocarbon readings exceeding the span.

  • The content of these primary categories can be found in Table 6 below.

  • COMS calibration error audits will be performed before the end of each half-year following permit issuance following the procedure described in 40 CFR Part 60, Appendix B, Performance Specification 1, section 7.1.4. Calibration error audits summaries are required to be submitted within 30 days after the end of each calender half-year following permit issuance.

  • Calibration error check documentation , and (viii) Copy of calibration gas certificates.

Related to Calibration error

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Medication error means any preventable event that may cause or lead to inappropriate medication use or patient harm, while the medication is in the control of the health care professional, patient, or consumer. Such events may be related to professional practice, health care products, procedures, and systems including, but not limited to: prescribing; order communication; product labeling, packaging and nomenclature; compounding; dispensing; distribution; administration; education; monitoring; and use.

  • Manifest Error means any error that we reasonably believe to be obvious or palpable, including without limitation, offers to execute Transactions for exaggerated volumes of Underlying Assets or at manifestly incorrect market price quotes or prices at a clear loss.

  • Root Cause Analysis Report means a report addressing a problem or non-conformance, in order to get to the ‘root cause’ of the problem, which thereby assists in correcting or eliminating the cause, and prevent the problem from recurring.

  • Workaround means a temporary modification to or change in operating procedures for the Work that: (i) circumvents or effectively mitigates the adverse effects of a Defect so that the Work complies with and performs in accordance with the applicable Specifications and Documentation; (ii) does not require substantial reconfiguration of the Work or any reloading of data; and (iii) does not otherwise impose any requirements that would impede an end user’s efficient use of the Work.

  • Technical Specifications means the detailed requirements for the Work furnished by the Architect and set forth in Book 3 of the Contract Documents.