Hot Spot Temperature definition

Hot Spot Temperature means the highest temperature of the Furnace breastwall refractory. Breastwall refractory is the refractory sidewall between the tuck stone (about 18” above glass line) and the crown skew (where the Furnace crown meets the Furnace sidewall).
Sample 1Sample 2Sample 3
Hot Spot Temperature means the highest temperature of the Furnace sidewall between the tuck stone (approximately 18” above the glass line) and the crown skew (where the Furnace crown meets the Furnace sidewall) (also referred to as the Furnace “breastwall refractory”);
Sample 1

Examples of Hot Spot Temperature in a sentence

  • Changing weather patterns contribute to yearlydifferences in ozone concentrations from region to region.

  • The major factor in transformer loss of life is the degradation of the winding insulation due to thermal stress which can be predicted by estimating the Hot Spot Temperature (HST), the highest temperature observed in the winding.

  • IEC 60076 Rating Maximum Hot Spot Temperature The maximum allowable winding hot spot temperature shall not exceed 68oC at an ambient temperature of 35oC, using a winding temperature hot spot gradient factor as determined by magnetic leakage field plots at the IEC 60076 Part 2 continuous ONAN rating on all tappings.

  • End Turn Hot Spot Temperature vs‌RequirementCurrent and Coolant Flow Rate Table 10.

  • Hot Spot Temperature assessmentTemperature as function of time for all the quenches (segment U4-U5) Maximum Temperature 220 KHigh MIITs tests Training quenchesIII.

  • The permissible temperature rise shall not exceed the limits of 40ºC (when measured by resistance method) for transformer winding and 35ºC (measured by thermometer) for top oil when tested in accordance with IS 2026(Part-2).(b) Hot Spot Temperature:-The Hot Spot Temperature at annual weighted average ambient temperature of 35oC shall be 98.2oC (Maximum).

  • Example Winding Thermal Profiles for 100 kW Tilt Rotor Motor Designed for Thermal Aging Only3503002502001501005000 500 1000 1500 2000 2500 3000 3500Mission Time (s)No T Limit D1No T Limti D2No T Limit D1 Engine OutNo T Limit D2 Engine OutWinding Hot Spot Temperature (degC)The first study carried out for the tilt rotor type vehicle was a study for a 100 kW hover power motor with design for thermal aging, no temperature limits, 6 vehicle rotors, and the single objective optimization function.

  • Hot Spot Temperature assessment Three independent methods to derive the temperature of the segmentsduring the quenches from:  the experimental voltage and current signals theoretical temperature dependences for the material(Copper, Nb3Sn, G10 ) properties (resistivity and heat capacity)III.

  • Loading guides IEEE C57.91 [2] and IEC 60076-7 [3] allow large power transformers to be dynamically rated up to the Hot Spot Temperature (HST) of 160 ◦C.

  • Xxxxxxxxxxx Superconductor Science and Technology Volume 28, Number 6 IOP Publishing Online 2015 - Link No 55 Hot Spot Temperature in an HTS Coil: Simulations With MIITs and Finite Element Method X.

Related to Hot Spot Temperature

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Operating pressure means the pressure at which the parts of an irrigation system are designed by the manufacturer to operate.

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • Hot Weather Alert means the notice provided by PJM to PJM Members, Transmission Owners, resource owners and operators, customers, and regulators to prepare personnel and facilities for extreme hot and/or humid weather conditions which may cause capacity requirements and/or unit unavailability to be substantially higher than forecast are expected to persist for an extended period.

  • Sensor means any measurement device that is not part of the vehicle itself but installed to determine parameters other than the concentration of gaseous and particle pollutants and the exhaust mass flow.

  • medium voltage means the set of nominal voltage levels that lie above low voltage and below high voltage in the range of 1 kV < Un 44 kV. [SANS 1019]

  • Bottle means any vessel intended to contain liquids and having a capacity of not more than 43

  • Biomass means the biodegradable fraction of products, waste and residues from biological origin from agriculture (including vegetal and animal substances), forestry and related industries including fisheries and aquaculture, as well as the biodegradable fraction of industrial and municipal waste;

  • Storage area means any location, facility, or vehicle which is used to store, to transport, or to secure a radiographic exposure device, a storage container, or a sealed source when it is not in use and which is locked or has a physical barrier to prevent accidental exposure, tampering with, or unauthorized removal of the device, container, or source.

  • Calibration gas means a gas mixture used to calibrate gas analysers.

  • Cold Weather Alert means the notice that PJM provides to PJM Members, Transmission Owners, resource owners and operators, customers, and regulators to prepare personnel and facilities for expected extreme cold weather conditions.

  • Density means the permitted number of dwelling units per

  • Finished water means the water that is introduced into the distribution system of a public water system and is intended for distribution and consumption without further treatment, except as treatment necessary to maintain water quality in the distribution system (e.g., booster disinfection, addition of corrosion control chemicals).

  • Tank means an enclosed space which is formed by the permanent structure of a ship and which is designed for the carriage of liquid in bulk.

  • Sewage sludge weight means the weight of sewage sludge, in dry U.S. tons, including admixtures such as liming materials or bulking agents. Monitoring frequencies for sewage sludge parameters are based on the reported sludge weight generated in a calendar year (use the most recent calendar year data when the NPDES permit is up for renewal).

  • Blend means seed consisting of more than one variety of a kind, each in excess of five percent by weight of the whole.

  • Bulk gasoline plant means a gasoline storage and distribution facility with an average daily throughput of 20,000 gallons (76,000 liters) of gasoline or less on a 30-day rolling average.

  • Meters shall have the meaning set forth in Section 4.6(a) hereof.

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Reid vapor pressure means the vapor pressure of crude oil or other volatile petroleum products at 100 degrees Fahrenheit as determined by the latest edition of ASTM D6377 (RVPE): Standard Test Method for Determination of Vapor Pressure of Crude Oil.

  • Beam scattering foil means a thin piece of material (usually metallic) placed in the beam to scatter a beam of electrons in order to provide a more uniform electron distribution in the useful beam.

  • Diesel means a distillate oil which can be used as fuel for the operation of a compression ignition engine and which has an approximate boiling temperature of between 150 °C to 400 °C;

  • technical specification means a document that prescribes technical requirements to be fulfilled by a product, process or service;

  • Gasohol means a blended fuel composed of gasoline and fuel grade ethanol.

  • Outputs means the goods or services that are produced by an entity or other person;

  • Modular building manufacturer means a person or corporation who owns or operates a