Mechanical Check definition

Mechanical Check means an audio visual external inspection and test drive of the Vehicle in accordance with clause 1 of this Important Notice.
Sample 1Sample 2Sample 3

Examples of Mechanical Check in a sentence

  • At the Millennium +5 Summit in 2005 world leaders reaffirmed democracy as “a universal value based on the freely expressed will of people to determine their own political, economic, social and cultural system.”47 The most accepted justification for the protection of the freedom of the media and expression is directly linked to the right to know and the right to participate.As Article 19 has expressed it: Freedom of expression makes electoral democracy meaningful and builds public trust in administration.

  • In particular, please note that (without limiting the foregoing) Vehicles over 5 years old; those that have a high mileage and/or have been subjected to abnormal use may have latent defects which fall outside the scope of the AA Mechanical Check.

  • This may highlight other defects, giving rise to repairs which are necessary but which were not apparent on the external visual check carried out for the AA Mechanical Check.

  • The location where the AA Mechanical Check took place, whether inside or outside, had good quality lighting or daylight.

  • Any AA Mechanical Check will be carried out subject to the Important Notice which is current at the date the AA Mechanical Check is booked.

  • AA Mechanical Checks are only available on Vehicles which are 10 years old or less from the date of registration to the date of the Mechanical Check request.

  • The Engineer is unable to confirm its internal condition or effectiveness as this requires exhaust emissions testing, which is beyond the scope of the AA Mechanical Check.

  • We cannot advise of defects if we cannot see them, or they are not apparent during the AA Mechanical Check of the Vehicle concerned.

  • The Engineer shall provide the AA Mechanical Check and Report with reasonable care and skill.

  • There is no road quires a well-planned skill-development sys• map.

Related to Mechanical Check

  • Electrical contractor means an electrical contractor as defined in the Regulations;

  • Contract Monitor means the Department employee identified in Section 1.6 of the IFB as the Contract Monitor.

  • SCADA means supervisory control and data acquisition.

  • technical specification means, with respect to any Software, the document setting forth the technical specifications for such Software and included in the Statement of Work.

  • Installation inspector means a person who, by reason of his knowledge of the physical sciences and the principles of engineering, acquired by a professional education and related practical experience, is qualified to supervise the installation of tank systems.

  • Design-Builder means the Person selected pursuant to the RFP that enters into the Contract with the Department to design and construct the Project (also referred to as the “Design-Build Team”).

  • Filter means material placed in the useful beam to preferentially absorb selected radiations.

  • Technician means an individual determined to be qualified to remove or process parts by an appropriate organization that is licensed, accredited, or regulated under federal or state law. The term includes an enucleator.

  • Design flow means the average annual flow or average daily flow specified in an approved facilities plan or approved plans and specifications, the flow specified in a WPDES permit, or the flow required to meet performance standards.

  • Routine maintenance means activities to keep an impervious surface as near as possible to its constructed condition. This includes ordinary maintenance activities, resurfacing paved areas, and exterior building changes or improvements which do not materially increase or concentrate stormwater runoff, or cause additional nonpoint source pollution.

  • Punch List Items means such items (i) as are reasonably necessary or appropriate to fully complete the construction, equipping and furnishing of the Hotel in accordance with this Contract and (ii) that, unless otherwise agreed by Buyer in its sole discretion, (a) individually and in the aggregate do not and will not prohibit, cause a delay in or otherwise adversely affect, under applicable Legal Requirements, the Franchise Agreement or otherwise, the opening of the Hotel for business to the public or the continued occupancy and operation of the Hotel as contemplated under the Brand and (b) may be corrected or completed, subject to delays caused by Force Majeure, within not more than sixty (60) days.

  • Graffiti shall not include: (1) any sign or banner that is authorized by, and in compliance with, the applicable requirements of the San Francisco Public Works Code, the San Francisco Planning Code or the San Francisco Building Code; or (2) any mural or other painting or marking on the property that is protected as a work of fine art under the California Art Preservation Act (California Civil Code Sections 987 et seq.) or as a work of visual art under the Federal Visual Artists Rights Act of 1990 (17 U.S.C. §§ 101 et seq.). Any failure of Contractor to comply with this section of this Agreement shall constitute an Event of Default of this Agreement.

  • Technical Specifications means the detailed requirements for the Work furnished by the Architect and set forth in Book 3 of the Contract Documents.

  • Electrical work Concealed and fire resistant wiring of “ISI” Copper Wire, Distribution board with “MCB”. “ISI” xxxx modular electrical accessories, Landline phone conduit, Cable TV wiring conduit, Separate line for inverter connection, Air-conditioner power point. Painting : Long Lasting and weather resistant acrylic paint to all external walls, All internal walls with white cement based putty finish with OBD. Plumbing & Sanitation : Sanitary xxxx for toilets, plumbing fixtures, CPVC/UPVC pipe and fitting(ISI make), SWR drainage system. Kitchen: Granite platform, ceramic tiles dado upto 2’ height, Stainless Steel sink in Kitchen, Aquaguard point, Connection for washing machine in wash area.

  • Project Management Report means each report prepared in accordance with Section 4.02 of this Agreement;

  • piece-work means any work the pay for which is estimated by the amount of work performed irrespective of the time occupied in its performance;

  • Enclosure means the part enclosing the internal units and providing protection against any direct contact.