MECHANICAL ENGINEERING WORKS definition

MECHANICAL ENGINEERING WORKS means mechanical installations other thanmechanical installations ancillary to building works
Sample 1Sample 2Sample 3
MECHANICAL ENGINEERING WORKS means mechanical installations other than
Sample 1Sample 2Sample 3
MECHANICAL ENGINEERING WORKS means mechanical installations other than mechanical installations ancillary to building works
Sample 1Sample 2

Examples of MECHANICAL ENGINEERING WORKS in a sentence

  • The design experience shall be a minimum of six months.FIELD EXPERIENCETHE CANDIDATE IS EXPECTED TO HAVE SUFFICIENT WORKSHOP/SITE EXPERIENCE IN THE SUPERVISION, FABRICATION, INSTALLATION, COMMISSIONING, OPERATION AND MAINTENANCE OF MECHANICAL ENGINEERING WORKS AND/OR OTHER RELATED WORKS AND FAMILIAR WITH ALL REGULATIONS AND CODES GOVERNING SAFE PRACTICE.

  • Engr.(C&W)For and On behalf of President of India)Address ……………………….Date …………..Date ……………….Witnesses ……………….Signature of witnesses with address to Signature to Contractor 1) 2) STANDARD GENERAL CONDITIONS OF CONTRACT 2014 AND CORRECTED UP TO DATE FOR USE IN MECHANICAL ENGINEERING WORKS WILL BE APPLICABLE.

  • Water Meters MECHANICAL ENGINEERING WORKS (ME): Particularly related to the supply, construction, repair and refurbishment of the following types of works but not limited to the list below: a.

  • It was noted that the Ministry support was due to issues remaining irreconcilable.

  • The evaluation process focussed on various aspects of the functioning of the Board such as composition of the Board and Committees, experience and competencies, performance of specific duties and obligations, governance issues, etc.Stakeholders Relationship Committee:The Board has constituted a Stakeholders Relationship Committee comprising of three Non-Executive Directors namely, Mr. N.

  • Sand filter refurbishment b) MECHANICAL ENGINEERING WORKS (ME) Particularly related to the construction, repair and refurbishment of the following types of works but not limited to below list:(a) Hydro-mechanical equipment (incl.

  • Until a formal agreement is prepared and executed, acceptance of this tender shall constitute a binding contract between us subject to modifications, as may be mutually agreed to between us and indicated in the letter of acceptance of my/our offer for this work .Signature of witnesses: Signature of Tenderer 1.2.Tenderer’s Signature REGULATIONS FOR TENDERS AND CONTRACTS FOR GUIDANCE OF CONTRACTORS FOR MECHANICAL ENGINEERING WORKS – MEANING OF TERMS.

Related to MECHANICAL ENGINEERING WORKS

  • Geotechnical engineer means a professional engineer registered with the Association of Professional Engineers, Geologists, and Geophysicists of the Northwest Territories and whose principal field of specialization is the design and construction of earthworks in a permafrost environment;

  • Systems Engineering means preparing specifications, identifying and resolving interface problems, developing test requirements, evaluating test data, and supervising design.

  • Design engineer means a person professionally qualified and duly licensed in New Jersey to perform engineering services that may include, but not necessarily be limited to, development of project requirements, creation and development of project design and preparation of drawings and specifications.

  • Engineering means the application of scientific knowledge for the design, control, or use of building structures, equipment, or apparatus.

  • Structural Engineer means the Engineer appointed or to be appointed from time to time by Promoter for the preparation of the structural design and drawings of the buildings .

  • engineering services means infrastructure for –

  • Engineering control means the use of substitution, isolation, ventilation, and equipment modification to reduce exposure to SARS-CoV-2 virus and COVID-19 disease related workplace hazards and job tasks.

  • external engineering service means an engineering service situated outside the boundaries of a land area and that is necessary to serve the use and development of the land area;

  • CHIEF MECHANICAL ENGINEER means the Chief Mechanical Engineer of the Chennai Port Trust.

  • The Works/Project means the works to be executed or done under this contract.

  • Mechanical Completion means that (a) all components and systems of the Project have been properly constructed, installed and functionally tested according to EPC Contract requirements in a safe and prudent manner that does not void any equipment or system warranties or violate any permits, approvals or Laws; (b) the Project is ready for testing and commissioning, as applicable; (c) Seller has provided written acceptance to the EPC Contractor of mechanical completion as that term is specifically defined in the EPC Contract.

  • Technical Specifications means the detailed requirements for the Work furnished by the Architect and set forth in Book 3 of the Contract Documents.

  • Practice of engineering means any service or creative work, the adequate performance of which requires engineering education, training, and experience in the application of special knowledge of the mathematical, physical, and engineering sciences.

  • Digital audio-visual work means a series of related images which, when shown in succession, imparts an impression of motion, together with accompanying sounds, if any.

  • technical specification means, with respect to any Software, the document setting forth the technical specifications for such Software and included in the Statement of Work.

  • Digital audio-visual works which means a series of related images which, when shown in succession, impart an impression of motion, together with accompanying sounds, if any;

  • Fabrication means making up data or results and recording or reporting them.

  • Architect/Engineer (A/E means a person registered as an architect pursuant to Tex. Occ. Code Ann., Ch. 1051, as a landscape architect pursuant to Tex. Occ. Code Ann., Ch. 1052, a person licensed as a professional engineer pursuant Tex. Occ. Code Ann., Ch. 1001, and/or a firm employed by Owner or Design-Build Contractor to provide professional architectural or engineering services and to exercise overall responsibility for the design of a Project or a significant portion thereof, and to perform the contract administration responsibilities set forth in the Contract.

  • Construction Phase Services means the coordination, implementation and execution of the Work required by this Agreement, which are further defined in Article 8.

  • Diesel engine means an internal combustion, compression-ignition (CI) engine with operating characteristics significantly similar to the theoretical diesel combustion cycle. The regulation of power by controlling fuel supply in lieu of a throttle is indicative of a compression ignition engine.

  • Manufacturing means all activities related to the manufacture of a Compound, including planning, purchasing, manufacture, processing, compounding, storage, filling, packaging, waste disposal, labeling, leafleting, testing, quality assurance, sample retention, stability testing, release, dispatch and supply, as applicable.

  • Value Engineering means the detailed analysis of systems, equipment, materials, services, facilities, and supplies required by the Contract Documents for the purpose of achieving the desired and essential functions of the Owner’s program at the lowest cost consistent with required and necessary performance, longevity, reliability, quality and safety.

  • Standard Specifications means a compilation in book form of specifica- tions approved for general application and repetitive use;

  • Design-Builder means the Person selected pursuant to the RFP that enters into the Contract with the Department to design and construct the Project (also referred to as the “Design-Build Team”).

  • Electrical contractor means an electrical contractor as defined in the Regulations;

  • Clean coal technology demonstration project means a project using funds appropriated under the heading “Department of Energy—Clean Coal Technology,” up to a total amount of $2,500,000,000 for commercial demonstration of clean coal technology, or similar projects funded through appropriations for the Environmental Protection Agency. The federal contribution for a qualifying project shall be at least 20 percent of the total cost of the demonstration project.