Proper practices means those set out in The Practitioners’ Guide
Applicable Technical Requirements and Standards means those certain technical requirements and standards applicable to interconnections of generation and/or transmission facilities with the facilities of an Interconnected Transmission Owner or, as the case may be and to the extent applicable, of an Electric Distributor, as published by Transmission Provider in a PJM Manual provided, however, that, with respect to any generation facilities with maximum generating capacity of 2 MW or less (synchronous) or 5 MW or less (inverter-based) for which the Interconnection Customer executes a Construction Service Agreement or Interconnection Service Agreement on or after March 19, 2005, “Applicable Technical Requirements and Standards” shall refer to the “PJM Small Generator Interconnection Applicable Technical Requirements and Standards.” All Applicable Technical Requirements and Standards shall be publicly available through postings on Transmission Provider’s internet website.
Good Industry Practices means the practices that would be adopted by, and the exercise of that degree of care, skill, diligence, prudence and foresight that reasonably would be expected from, a competent contractor in the international oil and gas industry experienced in performing work similar in nature, size, scope and complexity to the Work and under conditions comparable to those applicable to the Work, where such work is subject to, and such contractor is seeking to comply with, the standards and codes specified in the Contract or (to the extent that they are not so specified) such national or international standards and codes as are most applicable in the circumstances, and the applicable Law.
Codes and Standards means all the applicable codes and standards as indicated in the Technical Specification.
Clean air standards, as used in this clause means:
Best Practices means a term that is often used inter-changeably with “evidence-based 24 practice” and is best defined as an “umbrella” term for three levels of practice, measured in relation to 25 recovery-consistent mental health practices where the recovery process is supported with scientific 26 intervention that best meets the needs of the Client at this time.
27 a. EBP means Evidence-Based Practices and refers to the interventions utilized for which 28 there is consistent scientific evidence showing they improved Client outcomes and meets the following 29 criteria: it has been replicated in more than one geographic or practice setting with consistent results; it
Safety Standards means all laws, union rules and trade or industry custom or codes of any kind whatsoever, in effect from the date of this Agreement through Final Acceptance of the construction work, pertaining to worker safety and accident prevention applicable to the Project and/or the construction work (including, but not limited to, rules, regulations and standards adopted pursuant to the Occupational Safety and Health Act of 1970, as amended from time to time).
Community practice protocol means a written, executed agreement entered into voluntarily between an authorized pharmacist and a physician establishing drug therapy management for one or more of the pharmacist’s and physician’s patients residing in a community setting. A community practice protocol shall comply with the requirements of subrule 8.34(2).
Prudent Industry Practices means, at a particular time, any of the practices, methods, standards of care, skill, safety and diligence, as the same may change from time to time, but applied in light of the facts known at the time, that are consistent with the general standards applied or utilized under comparable circumstances by a reasonably prudent operator, in a good and workmanlike manner, with due diligence and dispatch, in accordance with good midstream industry practice.
Reasonable and prudent parent standard means the
Good Industry Practice means standards, practices, methods and procedures conforming to the Law and the degree of skill and care, diligence, prudence and foresight which would reasonably and ordinarily be expected from a skilled and experienced person or body engaged in a similar type of undertaking under the same or similar circumstances.
Good Utility Practices mean any of the practices, methods or acts engaged in or approved by a significant portion of the electric energy industry with respect to similar facilities during the relevant time period which in each case, in the exercise of reasonable judgment in light of the facts known or that should have been known at the time a decision was made, could have been expected to accomplish the desired result at reasonable cost consistent with good business practices, reliability, safety, law, regulation, environmental protection and expedition. Good Utility Practices are not intended to be limited to the optimum practices, methods or acts to the exclusion of all others, but rather to delineate the acceptable practices, methods or acts generally accepted in such industry.
Prudent Utility Practices means the practices, methods and standards that are generally accepted internationally from time to time by electric utilities for the purpose of ensuring the safe, efficient and economic design, construction, commissioning, operation and maintenance of power generation equipment and which practices, methods and standards shall be adjusted as necessary, to take account of: a) operation and maintenance guidelines recommended by the manufacturers of the plant and equipment to be incorporated in the Power Project; b) the requirements of Indian Law; and the physical conditions at the site of the Power Project
Applicable effluent standards and limitations means all State and Federal effluent standards and limitations to which a discharge is subject under the Act, including, but not limited to, effluent limitations, standards of performance, toxic effluent standards and prohibitions, and pretreatment standards.
Privacy Standards means the standards of the privacy of individually identifiable health information, as pursuant to HIPAA.
Good Manufacturing Practices means current good manufacturing practices, as set forth in 21 C.F.R. Parts 210 and 211.
Applicable Standards means the requirements and guidelines of NERC, the Applicable Regional Entity, and the Control Area in which the Customer Facility is electrically located; the PJM Manuals; and Applicable Technical Requirements and Standards.
Restorative practices means practices that emphasize repairing the harm to the victim and the school community caused by a student's misconduct.
Uniform Standards of Professional Appraisal Practice means the current standards of the appraisal profession, developed for appraisers and users of appraisal services by the Appraisal Standards Board of the Appraisal Foundation.
Codes of Practice means all codes of practice, rules of procedure, guidelines, directions, scheme rules and other requirements issued by the Bank System and specified from time to time as being applicable to the EMV PSP Service and your use of those.
Quality Standards means the quality standards published by BSI British Standards, the National Standards Body of the United Kingdom, the International Organisation for Standardisation or other reputable or equivalent body, (and their successor bodies) that a skilled and experienced operator in the same type of industry or business sector as the Contractor would reasonably and ordinarily be expected to comply with, and as may be further detailed in the Specification.
Servicer Policies and Practices means, with respect to the Servicer’s duties under Exhibit A to the Servicing Agreement, the policies and practices of the Servicer applicable to such duties that the Servicer follows with respect to comparable assets that it services for itself and, if applicable, others.
Reliability Standards means the criteria, standards, rules and requirements relating to reliability established by a Standards Authority.
NERC Reliability Standards means the most recent version of those reliability standards applicable to the Generating Facility, or to the Generator Owner or the Generator Operator with respect to the Generating Facility, that are adopted by the NERC and approved by the applicable regulatory authorities, which are available at xxxx://xxx.xxxx.xxx/files/Reliability_Standards_Complete_Set.pdf, or any successor thereto.
Accessibility Standards means accessibility standards and specifications for Texas agency and institution of higher education websites and EIR set forth in 1 TAC Chapter 206 and/or Chapter 213.
Pretreatment standards means all applicable Federal rules and regulations implementing Section 307 of the Act, as well as any nonconflicting State or local standards. In cases of conflicting standards or regulations, the more stringent thereof shall be applied.