Return Piping definition

Return Piping means that piping through which water is returned to the pool.
Return Piping means that part of the piping between the filter and the pool or spa through which passes the filtered water. (This piping frequently is referred to as "effluent piping".)
Return Piping means the piping which carries the filtered water under pressure from the filter to the pool.

Examples of Return Piping in a sentence

  • You agree that you shall not copy, duplicate, recreate or record or otherwise keep in possession or deliver to anyone other than the Company, any of the aforementioned items.

  • Two surveys were conducted this quarter at the Purcell, OK forum.

  • Hot Water Piping Cold Water Make-Up Piping Hot Water Recirculating Piping Low Pressure Steam Piping Medium Pressure Steam Piping High Pressure Steam Piping Condensate Return Piping Chilled Water Piping Combination Hot and Chilled Water Piping Chillers and Absorption Machine Breechings Stacks Grease Ducts Exhaust Ducts Boilers Expansion Tanks Pumps Fresh Air Intake Housings (Internal and External) C.

  • Vapor Recovery Piping Configurations NOTE: Vapor Return Piping shall meet the requirements specified in section 4.11 of CP-201.

  • In this subsection, a comparison of the model selection and predictions for a different distribution of innovations is analyzed.

  • Section 2D.0953 removing the duplicate rule ‘‘Vapor Return Piping for Stage II Vapor Recovery.

  • Pipe Identification: Provide plastic "wrap around" identification markers by Seton, Brady, Kolbi, or Setmark or approved equal indicating flow direction and fluid flowing for the following: Hot Water Supply Piping, Hot Water Return Piping.

  • Condensate Return Piping Replacement at the Cordell Hull Building Construction was completed on this project during the First Quarter FY16.

  • Install pipe markers on the following systems: Hot Water Supply and Return Piping B.

  • STANDARD EQUIPMENT: Boiler Jacket, Cast Iron Boiler Battery, High Limit Control, Intermittent Electric Ignition Pilot System, Vent Damper Relay, Theraltimeter Gauge, Circulator With Return Piping To Boiler, Main Gas Burners, Gas Control (Includes Automatic Gas Valve, Gas Pressure Regulator, Intermittent Pilot, Safety Shutoff, Pilot Flow Adjustment, Pilot Filter),A.S.M.E. Relief Valve, Drain Valve, Spill Switch, Rollout Switch, Combination Gas Control, Automatic Vent Damper.


More Definitions of Return Piping

Return Piping means that piping through which water is returned to the pool. (lll) "Ring Buoy" means a ring-shaped floating buoy capable of supporting a user. (mmm) "Shallow Area" means portions of a pool or spa with water depths five feet or less.
Return Piping means that part of the piping between the filter and the facility throughwhich passes the filtered water.
Return Piping means that part of the piping between the filter and the pool or spa through which passes the filtered water. (This piping frequently is referred to as "effluent piping".) "ROPE AND FLOAT LINE" (transition rope) means a continuous line not less than one-fourth (1/4) inch in diameter that is supported by buoys and attached to opposite sides of a pool to separate the deep and shallow ends.
Return Piping means piping which is referred to as effluent.
Return Piping means that part of the piping between the filter and the facility
Return Piping means that portion of the circulation piping which extends from the outlet side of the filters to the pool.

Related to Return Piping

  • Runoff coefficient means the fraction of total rainfall that will appear at the conveyance as runoff.

  • Taximeter means any device for calculating the fare to be charged in respect of any journey in a hackney carriage or private hire vehicle by reference to the distance travelled or time elapsed since the start of the journey, or a combination of both; and

  • Fresh water means water, such as tap water, that has not been previously used in a process operation or, if the water has been recycled from a process operation, it has been treated and meets the effluent guidelines for chromium wastewater.

  • Basecoat means a coat of colored material, usually opaque, that is applied before graining inks, glazing coats, or other opaque finishing materials and is usually topcoated for protection.

  • Ballast means a device used with an electric discharge lamp to obtain necessary circuit conditions, such as voltage, current, and waveform, for starting and operating the lamp.

  • Flash point means the lowest temperature of a liquid at which its vapours form a flammable mixture with air;

  • Heat input means the product (expressed in mmBtu/time) of the gross calorific value of the fuel (expressed in Btu/lb) and the fuel feed rate into the combustion device (expressed in mass of fuel/time) and does not include the heat derived from preheated combustion air, recirculated flue gases, or ex- haust from other sources.

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Rack means a mechanism for delivering motor vehicle fuel or diesel from a refinery or terminal into a truck, trailer, railroad car, or other means of non-bulk transfer.

  • Pressure means relative pressure versus atmospheric pressure, unless otherwise stated.

  • fire hydrant means a fire plug or fixed pillar fire hydrant;

  • Slash means all debris created on the Work area by the precommercial thinning operation.

  • Bandwidth means a distributor’s defined tolerance used to flag data for further scrutiny at the stage in the VEE process where a current reading is compared to a reading from an equivalent historical billing period. For example, a 30 percent bandwidth means a current reading that is either 30 percent lower or 30 percent higher than the measurement from an equivalent historical billing period will be identified by the VEE process as requiring further scrutiny and verification;

  • Water Service Connection means the pipes and fixtures used for the purpose of supplying any premises in the Municipality with water from the Corporation’s water works that is located between the Corporation’s watermain in the street and the street property line abutting the premises so supplied.