Texture coating definition

Texture coating means any coating that is applied to a metal part or product which, in its finished form, consists of discrete raised spots of the coating.
Sample 1Sample 2Sample 3
Texture coating means a coating that is applied to a plastic part that, in its finished form, consists of discrete raised spots of the coating.
Sample 1Sample 2Sample 3

Examples of Texture coating in a sentence

  • Texture coating: a coating that is applied to a plastic part which, in its finished form, consists of discrete raised spots of the coating.

  • Floor of MS Tubular pipes with floor material of BWP Marine Grade Ply Board 12mm thick with aluminium sheet on top, Wall material of BWP Marine Grade Ply Board 6mm thick, Four aluminium glass windows (2 No. Fix & 2 No. Sliding ), Sitting arrangement with cupboard, Texture coating paint off white / ivory / grey, Electrical points - 5AMP – 3 Nos.

  • Figure 3.8. The succession of fundamentals in Material B, plotted onto a staff, resembles the melodic lines found in Material A’s surface and deeper levels, shown in Appendix A.

  • The fan of the water blaster should be kepta minimum of 30cm from the surface of the Dulux AcraTex Texture coating in order to avoid damage.Alternatively you can clean the exterior walls with a solution of detergentand warm water using a soft brush.

  • The Office Building texture notes are more descriptive, than the Parking Garage notes.Answer: Texture coating will be applied to exterior surfaces as well as, exposed top and bottom of panels.

Related to Texture coating

  • High-temperature coating means a high performance coating labeled and formulated for application to substrates exposed continuously or intermittently to temperatures above 204oC (400oF).

  • Furniture coating means any paint designed for application to room furnishings including, but not limited to, cabinets (kitchen, bath and vanity), tables, chairs, beds, and sofas.

  • Touch-up coating means a coating used to cover minor coating imperfections appearing after the main coating operation.

  • Flat coating means a coating that is not defined under any other definition in this section and that registers gloss less than 15 on an 85-degree meter or less than 5 on a 60-degree meter.

  • Undercoating means any aerosol product designed to impart a protective, non-paint layer to the undercarriage, trunk interior, and/or firewall of motor vehicles to prevent the formation of rust or to deaden sound. “Undercoating” includes, but is not limited to, rubberized, mastic, or asphaltic products.

  • Flow coating means a coating labeled and formulated exclusively for use by electric power companies or their subcontractors to maintain the protective coating systems present on utility transformer units.

  • Faux finishing coating means a coating labeled and formulated as a stain or a glaze to create artistic effects including, but not limited to, dirt, old age, smoke damage, and simulated marble and wood grain.

  • Coating means a material applied onto or impregnated into a substrate for protective, decorative, or functional purposes. Such materials include, but are not limited to, paints, varnishes, sealers, and stains.

  • Metallic coating means a coating which contains more than five grams of metal particles per liter of coating, as applied. Metal particles are pieces of a pure elemental metal or a combination of elemental metals.

  • Basecoat means a coat of colored material, usually opaque, that is applied before graining inks, glazing coats, or other opaque finishing materials and is usually topcoated for protection.

  • Repair coating means a coating used to re-coat portions of a previously coated product which has sustained mechanical damage to the coating following normal coating operations.

  • Oxides of nitrogen means the sum of the volume mixing ratio (ppbv) of nitrogen monoxide (nitric oxide) and nitrogen dioxide expressed in units of mass concentration of nitrogen dioxide (µg/m3);

  • Pretreatment coating means a coating which contains no more than 12% solids by weight, and at least 0.5% acid by weight, is used to provide surface etching, and is applied directly to metal surfaces to provide corrosion resistance, adhesion, and ease of stripping.

  • Antenna coating means a coating labeled and formulated exclusively for application to equipment and associated structural appurtenances that are used to receive or transmit electromagnetic signals.

  • Roll coating means the application of a coating material to a substrate by means of hard rubber or steel rolls.

  • Floor coating means an opaque coating that is labeled and designed for application to flooring, including but not limited to, decks, porches, steps, and other horizontal surfaces which may be subject to foot traffic.

  • Air dried coating means a coating that is dried by the use of air or forced warm air at temperatures up to 1940F (900C).

  • Dip coating means the application of a coating material to a substrate by dipping the part into a tank of the coating material.

  • Single coat means one film coating applied to a metal surface.

  • Industrial maintenance coating means a high performance architectural coating, including primers, sealers, undercoaters, intermediate coats, and topcoats formulated for application to substrates, including floors, exposed to one or more of the following extreme environmental conditions listed below and labeled “For industrial use only;” “For professional use only;” “Not for residential use;” or “Not intended for residential use.”

  • Topcoat means a coating that is applied over a primer on an aerospace vehicle or component for appearance, identification, camouflage, or protection. Topcoats that are defined as specialty coatings are not included under this definition.

  • Automotive windshield washer fluid means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

  • Architectural coating means a coating applied to stationary structures and their appurtenances, to mobile homes, to pavements, or to curbs.

  • Low-solids coating means a coating containing 0.12 kilogram or less of solids per liter (one pound or less of solids per gallon) of coating material.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.