VOC composite partial vapor pressure definition

VOC composite partial vapor pressure means the sum of the partial pressure of the compounds defined as VOCs;
Sample 1Sample 2Sample 3

Examples of VOC composite partial vapor pressure in a sentence

  • The permittee shall maintain the as-applied VOC composite partial vapor pressure at or below ten mm Hg at twenty degrees Celsius (sixty-eight degrees Fahrenheit) for each cleaning solution used for cleaning on the press.

  • Beginning January 1, 2015, a person subject to subsection (a)(1)(i), (ii), (iii) or (iv) may not cause or permit the emission into the outdoor atmosphere of VOCs from cleaning solutions used in or on an offset lithographic printing press or a letterpress printing press unless the following conditions are met: (i) The cleaning solutions used must meet one or both of the following VOC limits: (A) A VOC composite partial vapor pressure less than 10 millimeters of mercury at 68°F (20°C).

  • Analysis by EPA Method 24 for VOC content or by an appropriate method for VOC composite partial vapor pressure of a sample of the cleaning solution.

  • No person shall operate a cold cleaner degreaser with a solvent that has a VOC composite partial vapor pressure that exceeds one (1) millimeter of mercury (nineteen-thousandths (0.019) pound per square inch) measured at twenty (20) degrees Celsius (sixty-eight (68) degrees Fahrenheit).

  • The recipe name, VOC content or VOC composite partial vapor pressure for each concentrated component or additive and cleaning solution mix ratio shall be recorded in a log book.

  • PPc= VOC composite partial vapor pressure at twenty degrees Celsius (sixty-eight degrees Fahrenheit), in mmHg. VPi = Vapor pressure of the “i”th VOC compound at twenty degrees Celsius (sixty-eight degrees Fahrenheit), in mmHg.

  • The actual VOC content of the material, as applied, as determined pursuant to Section 502.1, and for coating removers (strippers), surface preparation and cleaning material and application equipment cleanup material, the VOC composite partial vapor pressure.

  • VOC content shall be displayed as grams of VOC per liter of coating (or pounds of VOC per gallon), excluding water and exempt compounds, pursuant to Section 404.c. For coating removers (strippers), surface preparation and cleaning material and application equipment cleanup material the maximum VOC content of the material, as applied, after any mixing or thinning as recommended by the manufacturer, and the VOC composite partial vapor pressure.

  • Records of total applied volume for each material type exceeding the VOC limits specified in Sections 301 and 302 or the VOC composite partial vapor pressure limits specified in Section 302 by name/code/manufacturer and coating category.b. Daily:1.

  • Furthermore, it will provide a clear rationale for its findings concerning each ESG.

Related to VOC composite partial vapor pressure

  • Reid vapor pressure means the vapor pressure of crude oil or other volatile petroleum products at 100 degrees Fahrenheit as determined by the latest edition of ASTM D6377 (RVPE): Standard Test Method for Determination of Vapor Pressure of Crude Oil.

  • True vapor pressure means the equilibrium partial pressure exerted by a petroleum liquid as determined in accordance with methods described in American Petroleum Institute (API) Bulletin 2517, Evaporation Loss from External Floating Roof Tanks, 1980. The API procedure may not be applicable to some high viscosity or high pour crudes. Available estimates of true vapor pressure may be used in special cases such as these.

  • Backpressure means a pressure (caused by a pump, elevated tank or piping, boiler, or other means) on the consumer's side of the service connection that is greater than the pressure provided by the public water system and which may cause backflow.

  • Treatability study means a study in which a hazardous waste is subjected to a treatment process to determine: (1) Whether the waste is amenable to the treatment process, (2) what pretreatment (if any) is required, (3) the optimal process conditions needed to achieve the desired treatment, (4) the efficiency of a treatment process for a specific waste or wastes, or (5) the characteristics and volumes of residuals from a particular treatment process. Also included in this definition for the purpose of the § 261.4 (e) and (f) exemptions are liner compatibility, corrosion, and other material compatibility studies and toxicological and health effects studies. A “treatability study” is not a means to commercially treat or dispose of hazardous waste.

  • Aquatic plant means a plant, including the roots, which typically floats on water or requires water for its entire structural support, or which will desiccate outside of water.

  • Process weight means the total weight of all materials introduced into any source operation. Solid fuels charged will be considered as part of the process weight, but liquid and gaseous fuels and combustion air will not.

  • Diatomaceous earth filtration means a process resulting in substantial particulate removal in which a precoat cake of diatomaceous earth filter media is deposited on a support membrane (septum), and while the water is filtered by passing through the cake on the septum, additional filter media known as body feed is continuously added to the feed water to maintain the permeability of the filter cake.

  • Fluoroscopic imaging assembly means a subsystem in which X-ray photons produce a visual image. It includes the image receptor(s) such as the image intensifier and spot-film device, electrical interlocks, if any, and structural material providing linkage between the image receptor and diagnostic source assembly.

  • Composite sample means a combination of individual samples of wastewater taken at 1 hour intervals, for eight (8) hours (or for the duration of discharge, whichever is less), to minimize the effect of variability of the individual samples. Individual samples must be of equal volume. (Example: one (1) liter per hour.)

  • Structural components means liners, leachate collection systems, final covers, run-on/run-off systems, and any other component used in the construction and operation of the MSWLF that is necessary for protection of human health and the environment.

  • COVID-19 symptoms means fever of 100.4 degrees Fahrenheit or higher, chills, cough, shortness of breath or difficulty breathing, fatigue, muscle or body aches, headache, new loss of taste or smell, sore throat, congestion or runny nose, nausea or vomiting, or diarrhea, unless a licensed health care professional determines the person’s symptoms were caused by a known condition other than COVID-19.

  • Harvest batch means a specifically identified quantity of dried flower or trim, leaves, and other cannabis plant matter that is uniform in strain, harvested at the same time, and, if applicable, cultivated using the same pesticides and other agricultural chemicals, and harvested at the same time.

  • Volatile Organic Compound (VOC means any compound containing at least one atom of carbon, excluding carbon monoxide, carbon dioxide, carbonic acid, metallic carbides or carbonates, and ammonium carbonate, and excluding the following:

  • Instantaneous flow measurement means the flow measured during the minimum time required for the flow-measuring device or method to produce a result in that instance. To the extent practical, instantaneous flow measurements coincide with the collection of any grab samples required for the same sampling period so that together the samples and flow are representative of the discharge during that sampling period.

  • Structural component means a component that supports non-variable forces or weights (dead loads) and variable forces or weights (live loads).

  • Nitrogen oxides means nitric oxide and nitrogen dioxide, expressed as nitrogen dioxide (NO2);

  • Volatile organic compounds or “VOC” means any compound of carbon, excluding carbon monoxide, carbon dioxide, carbonic acid, metallic carbides or carbonates, and ammonium carbonate, which participates in atmospheric photochemical reactions.

  • Carbon dioxide equivalent or “CO2 equivalent” or “CO2e” means the number of metric tons of CO2 emissions with the same global warming potential as one metric ton of another greenhouse gas. Global warming potential values shall be determined consistent with the definition of Carbon Dioxide Equivalent in MRR section 95102(a).

  • Polystyrene foam adhesive means an aerosol adhesive designed to bond polystyrene foam to substrates.

  • High global warming potential hydrofluorocarbons means any hydrofluorocarbons in a particular end use for which EPA’s Significant New Alternatives Policy (SNAP) program has identified other acceptable alternatives that have lower global warming potential. The SNAP list of alternatives is found at 40 CFR part 82, subpart G, with supplemental tables of alternatives available at (http://www.epa.gov/snap/ ).

  • Therapeutically equivalent drug products means drug products that contain the same active ingredients and are identical in strength or concentration, dosage form, and route of administration and that are classified as being therapeutically equivalent by the U.S. Food and Drug Administration pursuant to the definition of "therapeutically equivalent drug products" set forth in the most recent edition of the Approved Drug Products with Therapeutic Equivalence Evaluations, otherwise known as the "Orange Book."

  • Back-Up Compound means, with reference to any particular Development Candidate or Drug Product Candidate, a Compound which (a) has the same principal mode of action (i.e., Potentiator or Corrector) as that Development Candidate or Drug Product Candidate; and (b) was among the group of Compounds, identified by VERTEX as potential additional lead molecules having the same principal mode of action, from which the Development Candidate was selected.

  • On-premise beer retailer means a beer retailer who is:

  • Silicone-based Multi-purpose Lubricant means any lubricant which is:

  • SO2 means sulfur dioxide.

  • Wind Turbine means a mechanical/electrical system that converts the kinetic energy of blowing wind into mechanical or electric power.