– AGREEMENT TO SELL 2.1 Vendor hereby agrees to sell to Purchaser such Products and Services as Purchaser may order from time to time by Purchase Order, all in accordance with and subject to the terms, covenants and conditions of this Agreement. Purchaser agrees to purchase those Products and Services ordered by Purchaser by Purchase Order in accordance with and subject to the terms, covenants and conditions of this Agreement.
CONTRACT MANAGEMENT AND EARLY TERMINATION 14 8.1 Contract Remedies. 14 8.2 Termination for Convenience 14 8.3 Termination for Cause 14 ARTICLE IX. MISCELLANEOUS PROVISIONS 15 9.1 Amendment 15 9.2 Insurance 15 9.3 Legal Obligations 15 9.4 Permitting and Licensure 16 9.5 Indemnity 16 9.6 Assignments 16 9.7 Independent Contractor 17 9.8 Technical Guidance Letters 17 9.9 Dispute Resolution 17 9.10 Governing Law and Venue 17 9.11 Severability 17 9.12 Survivability 18 9.13 Force Majeure 18 9.14 No Waiver of Provisions 18 9.15 Publicity 18 9.16 Prohibition on Non-compete Restrictions 19 9.17 No Waiver of Sovereign Immunity 19 9.18 Entire Contract and Modification 19 9.19 Counterparts 19 9.20 Proper Authority 19 9.21 E-Verify Program 19 9.22 Civil Rights 19 9.23 System Agency Data 21 v. 2 16.1 Effective 03/26/2019 HHSC Grantee Uniform Terms and Conditions Page 3 of 21
Payment to Subcontractors (If applicable) As required by Minnesota Statute § 16A.1245, the prime Contractor must pay all subContractors, less any retainage, within 10 calendar days of the prime Contractor’s receipt of payment from the State for undisputed services provided by the subContractor(s) and must pay interest at the rate of one and one-half percent per month or any part of a month to the subContractor(s) on any undisputed amount not paid on time to the subContractor(s).
PAYMENT TO SUB-CONTRACTORS 12.1 Transnet reserves the right, in its sole discretion, to make payment directly to the sub-contractor of the Supplier/Service Provider, subject to the following conditions:
Prompt Payment to Subcontractors (a) Within 7 days of receipt by the Contractor of each payment from the City under this contract, the Contractor shall pay all Subcontractors (which term includes subconsultants and suppliers) based on work completed or service provided under the subcontract. Should any payment to the Subcontractor be delayed by more than 7 days after receipt of payment by the Contractor from the City under this contract, the Contractor shall pay the Subcontractor interest, beginning on the 8th day, at the rate of 1% per month or fraction thereof on such unpaid balance as may be due. By appropriate litigation, Subcontractors shall have the right to enforce this subsection (a) directly against the Contractor, but not against the City of Durham.
Report of the Settlement Agreement to the Office of the Attorney General Of California
Obligation to Provide State Access to Grant Records The Grantee must make all grant records of expenditures, copies of reports, books, and related documentation available to the Division or a duly authorized representative of the State of Florida for inspection at reasonable times for the purpose of making audits, examinations, excerpts and transcripts.
Requirement to Have a Single Audit The Subrecipient will complete the Subrecipient Annual Report annually within 45 days after its fiscal year end, informing the State of Vermont whether or not a Single Audit is required for the prior fiscal year. If a Single Audit is required, the Subrecipient will submit a copy of the audit report to the granting Party within 9 months. If a single audit is not required, only the Subrecipient Annual Report is required. For fiscal years ending before December 25, 2015, a Single Audit is required if the subrecipient expends $500,000 or more in Federal assistance during its fiscal year and must be conducted in accordance with OMB Circular A-133. For fiscal years ending on or after December 25, 2015, a Single Audit is required if the subrecipient expends $750,000 or more in Federal assistance during its fiscal year and must be conducted in accordance with 2 CFR Chapter I, Chapter II, Part 200, Subpart F. The Subrecipient Annual Report is required to be submitted within 45 days, whether or not a Single Audit is required.
FAILURE TO HONOUR SETTLEMENT AGREEMENT 32. If this Settlement Agreement is accepted by the Hearing Panel and, at any subsequent time, the Respondent fails to honour any of the Terms of Settlement set out herein, Staff reserves the right to bring proceedings under section 24.3 of the By-laws of the MFDA against the Respondent based on, but not limited to, the facts set out in Part IV of the Settlement Agreement, as well as the breach of the Settlement Agreement. If such additional enforcement action is taken, the Respondent agrees that the proceeding(s) may be heard and determined by a hearing panel comprised of all or some of the same members of the hearing panel that accepted the Settlement Agreement, if available.
Please see the current Washtenaw Community College catalog for up-to-date program requirements Secondary / Post-Secondary Program Alignment Welding HIGH SCHOOL COURSE SEQUENCE 9th Grade 10th Grade 11th Grade 12th Grade English 9 Algebra I World History/Geography Biology World Language Phys Ed/Health English 10 Geometry U.S. History/Geography Physics or Chemistry World Language Visual/Performing/Applied Arts English 11 Algebra II Civics/Economics Welding English 12 Math Credit Science Credit Welding WASHTENAW COMMUNITY COLLEGE Welding Associate in Applied Science Semester 1 Math Elective(s)* 3 WAF 105 Introduction to Welding Processes 2 WAF 111 Oxy-fuel Welding 4 WAF 112 Shielded Metal Arc Welding 4 Semester Total 13 Semester 2 Speech Elective(s) 3 WAF 106 Blueprint Reading for Welders 3 WAF 123 Advanced Oxy-fuel Welding 4 WAF 124 Advanced Shielded Metal Arc Welding 4 Semester Total 14 Semester 3 Arts/Human. Elective(s) 3 Computer Lit. Elective(s) 3 WAF 215 Advanced Gas Tungsten Arc Welding 4 WAF 288 Gas Metal Arc Welding 4 Semester Total 14 Semester 4 WAF 200 Layout Theory Welding 3 WAF 210 Welding Metallurgy 3 Soc. Sci. Elective(s) 3 WAF 226 Specialized Welding Procedures 4 Semester Total 13 Semester 5 Nat. Sci. Elective(s) 4 WAF 227 Basic Fabrication 3 WAF 229 Shape Cutting Operations 3 Writing Elective(s) 3 Semester Total 13 Program Totals 67
