Annually by Vendor Sample Clauses

Annually by Vendor. Vendor Shall perform the following services on an annual basis 4.10.5.1 Clean hoistway. 4.10.5.2 Clean, lubricate and adjust hoistway door equipment. Burnish door interlock contacts and shorting bars. Replace worn parts as necessary. 4.10.5.3 Vacuum and clean the car safety mechanism. Operate moveable parts and ascertain that they move freely. 4.10.5.4 Change oil in sleeve bearings. 4.10.5.5 Clean and lubricate the deflector and secondary sheaves. Check grooves for wear. Report abnormal conditions. 4.10.5.6 Clean and lubricate the car and counterweight 2:1 sheaves. Check grooves for wear. Report abnormal conditions. 4.10.5.7 Clean, examine and lubricate compensating sheave. Check switch setting and tie-down mechanism. 4.10.5.8 Inspect car and counterweight oil buffers. Check for proper oil level. Actuate switches and reset. 4.10.5.9 Check car and counterweight run-by. 4.10.5.10 Check for abrasions or wear on traveling cables. 4.10.5.11 Inspect cab enclosure steadying devices. 4.10.5.12 Check and adjust car door pressure and speed. Log on maintenance chart. 4.10.5.13 Check car and main landing door gibs. Replace if worn. 841121.07/SD 371692-00006/2-27-20/MLT/pah EXHIBIT G -7- 12278 SCRIPPS SUMMIT DRIVE [Fate Therapeutics, Inc.] 4.10.5.14 Lubricate hoist ropes. 4.10.5.15 Blowout/vacuum hoist motor and motor generator. 4.10.5.16 Tighten mainline connections and check fuse sizing. Replace any fuses that appear damaged or unmarked. 4.10.5.17 Clean and check controller fuses and fuse holders. Ascertain that the proper fuse is installed. Replace any fuses that appear damaged or unmarked. 4.10.5.18 Test emergency power system. 4.10.5.19 Test earthquake device. 4.10.5.20 Activate Firemen's Return. 4.10.5.21 Perform other tests required by local code authorities.
Annually by Vendor. Vendor Shall perform the following services on a annual basis 3.14.1 Clean hoistway. 3.14.2 Clean, lubricate and adjust hoistway door equipment. Burnish door interlock contacts and shorting bars. Replace worn parts as necessary. 3.14.3 Vacuum and clean the car safety mechanism. Operate moveable parts and ascertain that they move freely. 3.14.4 Change oil in sleeve bearings. 3.14.5 Clean and lubricate the deflector and secondary sheaves. Check grooves for wear. Report abnormal conditions. 3.14.6 Clean and lubricate the car and counterweight 2:1 sheaves. Check grooves for wear. Report abnormal conditions. 3.14.7 Clean, examine and lubricate compensating sheave. Check switch setting and tie-down mechanism. 3.14.8 Inspect car and counterweight oil buffers. Check for proper oil level. Actuate switches and reset. 3.14.9 Check car and counterweight run-by. 3.14.10 Check for abrasions or wear on traveling cables. 3.14.11 Inspect cab enclosure steadying devices. 3.14.12 Check and adjust car door pressure and speed. Log on maintenance chart. 3.14.13 Check car and main landing door gibs. Replace if worn. 3.14.14 Lubricate hoist ropes.

Related to Annually by Vendor

  • Time to be Devoted to Employment During the Employment Period, the Executive will devote substantially all of the Executive’s working energies, efforts, interest, abilities and time exclusively to the business and affairs of the Company and its Affiliates. The Executive will not engage in any other business or activity which, in the reasonable judgment of the Board, would conflict or interfere in any material respect with the Executive’s performance of his duties as set forth herein, whether or not such activity is pursued for gain, profit or other pecuniary advantage.

  • Payment on Termination If an employee is terminated after the end of a year of employment, the employee is deemed to have been given any untaken leave from the date of termination and shall be paid for that leave accordingly. The employee shall also be paid for any public holidays falling within the period of leave in addition to payment for the leave. If an employee is terminated before the end of a full year of employment, the employee shall be paid pro-rata annual leave based on the period of service.

  • HOLIDAY COMPENSATION FOR TIME WORKED Employees required by their respective appointing officers to work on any of the above specified or substitute holidays, excepting Fridays observed as holidays in lieu of holidays falling on Saturday, shall be paid extra compensation of one additional day's pay at time- and-one-half the usual rate in the amount of 12 hours pay for 8 hours worked or a proportionate amount for less than 8 hours worked provided, however, that at the employee's request and with the approval of the appointing officer, an employee may be granted compensatory time off in lieu of paid overtime as provided for elsewhere in this contract. 127. Executive, administrative and professional employees designated in the Annual Salary Ordinance with the "Z" symbol shall not receive extra compensation for holiday work but may be granted time off equivalent to the time worked at the rate of-one-and-one-half times for work on the holiday.

  • Initial Term The initial term will begin on the date set forth in the Contract documents or on the date the Contract is signed by all Parties, whichever is later.

  • Four on, Two off Schedule In an effort to maximize full-time employment opportunities, the local parties may agree to a “four on, two off” innovative schedule, subject to the following principles: (a) The introduction of such schedules and trial periods, if any, shall be determined by the local parties. Each Home must have the majority agreement of the full-time and part- time employees who vote on the issue to agree on a trial period of up to six months. Once the trial period is complete, each Home must have a minimum of 66⅔% agreement of the full-time and part-time employees who vote on the issue to continue with the new schedule on a permanent basis. (b) The implementation of such schedules shall be established only by mutual agreement of the Employer and the Union. (c) Notwithstanding the definition for full-time employee under Article 2.02, employees who participate in this schedule will normally be scheduled for thirty-five (35) hours per week on average and will be considered a full- time employee for all purposes of the collective agreement. i) Notwithstanding Article 16.01, for the purposes of bi-weekly overtime, the normal weekly full-time hours shall remain at seventy-five (75) hours per bi-weekly average over a six (6) week period. In each bi-weekly pay period the employee will be paid for all hours worked. At the end of the six (6) week period, entitlement for bi-weekly overtime will be calculated and paid. ii) Notwithstanding Article 16.01, for the purposes of daily overtime, the normal daily hours shall remain at seven and a half (7.5) hours per day. In each bi-weekly pay period the employee will be paid for all hours worked including daily overtime, if any. (e) For the purposes of vacation entitlement, the current collective agreement provisions shall apply using thirty-five (35) hours per week. (f) Each facility/unit must have eighty percent (80%) agreement of the full- time and part-time employees who work in the facility/unit. (g) The Four on, Two off schedule, may be discontinued by either party upon receipt of twelve (12) weeks’ notice to the other in writing of its desire to terminate. A meeting shall be held within two (2) weeks of receipt of such notice to discuss the reasons for the discontinuation. The Four on, Two off schedule, may be discontinued by the Union in any facility/unit when sixty percent (60%) of the employees in the facility/unit so indicate by secret ballot to the Union.

  • Six-Month Delay Notwithstanding anything to the contrary in this Agreement, no compensation or benefits, including without limitation any severance payments or benefits payable under this Section 4, shall be paid to the Executive during the six-month period following the Executive’s Separation from Service if the Company determines that paying such amounts at the time or times indicated in this Agreement would be a prohibited distribution under Section 409A(a)(2)(B)(i) of the Code. If the payment of any such amounts is delayed as a result of the previous sentence, then on the first day of the seventh month following the date of Separation from Service (or such earlier date upon which such amount can be paid under Section 409A without resulting in a prohibited distribution, including as a result of the Executive’s death), the Company shall pay the Executive a lump-sum amount equal to the cumulative amount that would have otherwise been payable to the Executive during such period.

  • Salary Rate Upon Employment The hiring rate of pay for a new employee shall not be higher than the rate of pay for an existing employee in the same classification with similar work experience, training and education.

  • Continued Employment Following Expiration of Term Nothing in this Agreement shall mandate or prohibit a continuation of Executive’s employment following the expiration of the term of this Agreement, upon such terms and conditions as the Bank and Executive may mutually agree.

  • Repayment on Termination Date The Borrower hereby agrees to repay the outstanding principal amount of (i) all Revolving Credit Loans in full on the Revolving Credit Maturity Date, and (ii) all Swingline Loans in accordance with Section 2.2(b) (but, in any event, no later than the Revolving Credit Maturity Date), together, in each case, with all accrued but unpaid interest thereon.

  • Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers. 2.8.3.2 This element will be provided in MDUs and/or Multi-Tenants Units (MTUs) where either Party owns wiring all the way to the End User’s premises. Neither Party will provide this element in locations where the property owner provides its own wiring to the End User’s premises, where a third party owns the wiring to the End User’s premises.