Common use of Application for approval Clause in Contracts

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal collision shall be submitted by the vehicle manufacturer or by their duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents in triplicate and following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials; 3.2.2. Photographs, and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the interior fittings and protective systems installed in the vehicle; 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved with a sufficient degree of confidence. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test provided that it can be shown that the absence of the components has no detrimental effect on the results of the test in so far as the requirements of this Regulation are concerned. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. above is compatible with compliance with the requirements of this Regulation.

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal lateral collision shall be submitted by the vehicle manufacturer or by their his duly accredited representative. 3.2. It shall be accompanied by the undermentioned under mentioned documents in triplicate and the following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent constitutent materials; 3.2.2. Photographs, Photographs and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward lateral part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass’s mass as defined by paragraph 2.11. of this Regulation; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the relevant side interior fittings and protective systems installed in the vehicle; 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved on prototype vehicles with a sufficient degree of confidenceaccuracy. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test tests provided that it can be shown that the absence of the components omitted has no detrimental effect on the results of the test performance prescribed in so far as the requirements of this Regulation are concernedRegulation. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. 3.4.1 above is compatible with in compliance with the requirements of this Regulation.

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal lateral collision shall be submitted by the vehicle manufacturer or by their his duly accredited representative. 3.2. It shall be accompanied by the undermentioned under mentioned documents in triplicate and the following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent constitutent materials; 3.2.2. Photographs, Photographs and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward lateral part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass’s mass as defined by paragraph 2.11. of this Regulation; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the relevant side interior fittings and protective systems installed in the vehicle;. 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved on prototype vehicles with a sufficient degree of confidenceaccuracy. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test tests provided that it can be shown that the absence of the components omitted has no detrimental effect on the results of the test performance prescribed in so far as the requirements of this Regulation are concernedRegulation. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. above 3.4.1 is compatible with in compliance with the requirements of this Regulation.

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal collision shall be submitted by the vehicle manufacturer or by their duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents in triplicate and following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials; 3.2.2. Photographs, and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the interior fittings and protective systems installed in the vehicle; 3.2.6. A general description of the electrical power source type, location and the electrical electric power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved with a sufficient degree of confidence. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test provided that it can be shown that the absence of the components has no detrimental effect on the results of the test in so far as the requirements of this Regulation are concerned. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. above is compatible with compliance with the requirements of this Regulation.

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal collision shall be submitted by the vehicle manufacturer or by their his duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents in triplicate and following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials; 3.2.2. Photographs, and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the interior fittings and protective systems installed in the vehicle;. 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved with a sufficient degree of confidence. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service technical service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test provided that it can be shown that the absence of the components omitted has no detrimental effect on the results of the test in so far as the requirements of this Regulation are concerned. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. above is compatible with compliance with the requirements of this Regulation.

Application for approval. 3.1. The application for approval of a vehicle type with regard to the protection of the occupants of the front seats in the event of a frontal collision shall be submitted by the vehicle manufacturer or by their his duly accredited representative. 3.2. It shall be accompanied by the undermentioned documents in triplicate and following particulars: 3.2.1. A detailed description of the vehicle type with respect to its structure, dimensions, lines and constituent materials; 3.2.2. Photographs, and/or diagrams and drawings of the vehicle showing the vehicle type in front, side and rear elevation and design details of the forward part of the structure; 3.2.3. Particulars of the vehicle's unladen kerb mass; 3.2.4. The lines and inside dimensions of the passenger compartment; 3.2.5. A description of the interior fittings and protective systems installed in the vehicle; 3.2.6. A general description of the electrical power source type, location and the electrical power train (e.g. hybrid, electric). 3.3. The applicant for approval shall be entitled to present any data and results of tests carried out which make it possible to establish that compliance with the requirements can be achieved with a sufficient degree of confidence. 3.4. A vehicle which is representative of the type to be approved shall be submitted to the Technical Service responsible for conducting the approval tests. 3.4.1. A vehicle not comprising all the components proper to the type may be accepted for test provided that it can be shown that the absence of the components omitted has no detrimental effect on the results of the test in so far as the requirements of this Regulation are concerned. 3.4.2. It shall be the responsibility of the applicant for approval to show that the application of paragraph 3.4.1. above is compatible with compliance with the requirements of this Regulation.