Beneficiary Alignment Methodology
Beneficiary Alignment Methodology Sample Clauses
Related to Beneficiary Alignment Methodology
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C. 1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Payment Methods A. Except as otherwise provided by this Contract, the payment method will be one or more of the following:
Adoption Agreement The document executed by the Employer through which it adopts the Plan and agrees to be bound by all terms and conditions of the Plan.
Settlement Method Election Date The third Scheduled Trading Day immediately preceding the First Expiration Date.
Payment Method Payment shall be made by the Contractor to the Subcontractor as follows: (choose one) ☐ - Immediately upon completion of the Services to the satisfaction of the Contractor. ☐ - Within ____ business days after completion of the Services to the satisfaction of the Contractor. ☐ - Shall be paid on a ☐ weekly ☐ monthly ☐ quarterly ☐ other ______________________ basis. If the Subcontractor completes the Services to the satisfaction of the Contractor, before the full amount or balance has been fully paid, any remaining amount shall be payable immediately. ☐ - Other: ________________________________________________________
Settlement Method Election Physical Settlement, Cash Settlement, or Net Share Settlement, at the election of Counterparty as set forth in a Settlement Notice that satisfies the Settlement Notice Requirements; provided that Physical Settlement shall apply (i) if no Settlement Method is validly selected, (ii) with respect to any Settlement Shares in respect of which Dealer is unable, in good faith and in its commercially reasonable discretion, to unwind its commercially reasonable hedge by the end of the Unwind Period (taking into account any Additional Transactions with overlapping “Unwind Periods” (as defined in the applicable Additional Confirmations)) (A) in a manner that, in the reasonable discretion of Dealer, based on advice of counsel, is consistent with the requirements for qualifying for the safe harbor provided by Rule 10b-18 under the Exchange Act (“Rule 10b-18”) or (B) in its commercially reasonable judgment, due to the occurrence of five or more Disrupted Days or to the lack of sufficient liquidity in the Shares on any Exchange Business Day during the Unwind Period, (iii) to any Termination Settlement Date (as defined under “Termination Settlement” in Paragraph 7(g) below) and (iv) if the Final Date is a Settlement Date other than as the result of a valid Settlement Notice, in respect of such Settlement Date; provided, further, that, if Physical Settlement applies under clause (ii) immediately above, Dealer shall provide written notice to Counterparty at least two Scheduled Trading Days prior to the applicable Settlement Date.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Notification of Disbursement Method Form Pursuant to the Project Agreement executed for this loan, there are two methods by which funds can be disbursed. The first method is for the Ohio Public Works Commission (OPWC) to pay vendors directly. The second method is for the Commission to reimburse the subdivision after project costs have been incurred and paid by the subdivision. For loans only, the OPWC needs to be formally notified in advance as to which method the subdivision plans to utilize. Please refer to the enclosure entitled "Notification of Disbursement Method" and the accompanying "Instructions for Declaring Official Intent". In deciding which method to use please consider the following: • Discuss your disbursement options and preferences with your Project Manager, Xxxxx Xxxxx, prior to making a selection. • Passing a Resolution of Intent for the entire loan amount doesn't do you any harm and can actually be beneficial in the event the Commission needs to reimburse the subdivision in the event of an overpayment. • At any point during the life of the project you can always have the OPWC pay contractors directly even if you have passed a Resolution. • If you need to pass a Resolution, we encourage subdivisions to do so as early as possible. At a minimum, a Resolution must be adopted no later than 60 days after the date of construction related project costs for which the subdivision will seek reimbursement from us.
Xxxx Individual Retirement Custodial Account The following constitutes an agreement establishing a Xxxx XXX (under Section 408A of the Internal Revenue Code) between the depositor and the Custodian.
Individual Account An individual account is an account owned by you alone, which you as the account owner use during your lifetime.
