We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.

For more information visit our privacy policy.

Billing Meter Sample Clauses

Billing Meter. In the Interconnection Agreement between Seller and Transmission Provider, Seller shall arrange with the Transmission Provider to construct and install such meters and metering equipment as are necessary to measure the Energy delivered and received in accordance with the terms and conditions of this Agreement (the “Billing Meter”). Buyer shall provide to Seller the reasonable allowable accuracy limits relating to the performance of the Billing Meter, and Seller shall arrange with Transmission Provider to install and operate a Billing Meter that meets the allowable accuracy limits. Seller shall be responsible for paying the Transmission Provider for all costs relating to the Billing Meter, including, without limitation, its procurement, installation, operation, calibration, and maintenance. Seller shall ensure in its arrangement with the Transmission Provider for the Billing Meter to include communication equipment that enables Buyer to access and read the meter from a remote location. Seller hereby grants Buyer with rights to physically access the Billing Meter. Seller shall provide Buyer (at Seller’s cost) with appropriate telephonic/electronic communication to allow Buyer to remotely read the meter. Seller may, at its own expense, install and maintain additional metering equipment for purposes of monitoring, recording or transmitting data relating to its sale of Energy from the Facility, so long as such equipment does not interfere with the Billing Meter. Seller shall arrange with the Transmission Provider to test the Billing Meter at regular intervals. Seller shall also arrange for either Party to have the right to request and obtain, at reasonable intervals and under reasonable circumstances, additional/special tests of the Billing Meter. The Party making such request for the test shall incur the costs associated with such test.
Sample 1Sample 2Sample 3See All (9)
Billing Meter. In the Interconnection Agreement between Seller and Transmission Provider, Seller shall arrange with the Transmission Provider to construct and install such meters and metering equipment as are necessary to measure the Energy delivered and received in accordance with the terms and conditions of this Agreement (the “Billing Meter”). Buyer shall provide to Seller the reasonable allowable accuracy limits relating to the performance of the Billing Meter, and Seller shall arrange with Transmission Provider to install and operate a Billing Meter that meets the allowable accuracy limits. Seller shall be responsible for paying the Transmission Provider for all costs relating to the Billing Meter, including, without limitation, its procurement, installation, operation, calibration, and maintenance. Seller shall ensure in its arrangement with the Transmission Provider for the Billing Meter to include communication equipment that enables Buyer to access and read the meter from a remote location. Seller hereby grants Buyer with rights to physically access the Billing Meter. Seller shall provide Buyer (at Seller’s cost) with
Sample 1

Related to Billing Meter

  • Traffic Measurement and Billing over Interconnection Trunks 6.1 For billing purposes, each Party shall pass Calling Party Number (CPN) information on at least ninety-five percent (95%) of calls carried over the Interconnection Trunks. 6.1.1 As used in this Section 6, “Traffic Rate” means the applicable Reciprocal Compensation Traffic rate, Measured Internet Traffic rate, intrastate Switched Exchange Access Service rate, interstate Switched Exchange Access Service rate, or intrastate/interstate Tandem Transit Traffic rate, as provided in the Pricing Attachment, an applicable Tariff, or, for Measured Internet Traffic, the FCC Internet Order. 6.1.2 If the originating Party passes CPN on ninety-five percent (95%) or more of its calls, the receiving Party shall xxxx the originating Party the Traffic Rate applicable to each relevant minute of traffic for which CPN is passed. For any remaining (up to 5%) calls without CPN information, the receiving Party shall xxxx the originating Party for such traffic at the Traffic Rate applicable to each relevant minute of traffic, in direct proportion to the minutes of use of calls passed with CPN information. 6.1.3 If the originating Party passes CPN on less than ninety-five percent (95%) of its calls and the originating Party chooses to combine Reciprocal Compensation Traffic and Toll Traffic on the same trunk group, the receiving Party shall xxxx the higher of its interstate Switched Exchange Access Service rates or its intrastate Switched Exchange Access Services rates for all traffic that is passed without CPN, unless the Parties agree that other rates should apply to such traffic. 6.2 At such time as a receiving Party has the capability, on an automated basis, to use such CPN to classify traffic delivered over Interconnection Trunks by the other Party by Traffic Rate type (e.g., Reciprocal Compensation Traffic/Measured Internet Traffic, intrastate Switched Exchange Access Service, interstate Switched Exchange Access Service, or intrastate/interstate Tandem Transit Traffic), such receiving Party shall xxxx the originating Party the Traffic Rate applicable to each relevant minute of traffic for which CPN is passed. If the receiving Party lacks the capability, on an automated basis, to use CPN information on an automated basis to classify traffic delivered by the other Party by Traffic Rate type, the originating Party will supply Traffic Factor 1 and Traffic Factor

  • Interconnection Customer (1) Interconnection Customer shall construct and, unless otherwise indicated, shall own, the following Interconnection Facilities: None (2) In the event that, in accordance with the Interconnection Construction Service Agreement, Interconnection Customer has exercised the Option to Build, it is hereby permitted to build in accordance with and subject to the conditions and limitations set forth in that Section, the following portions of the Transmission Owner Interconnection Facilities which constitute or are part of the Customer Facility: None Ownership of the facilities built by Interconnection Customer pursuant to the Option to Build shall be as provided in the Interconnection Construction Service Agreement.

  • Check Meters Developer, at its option and expense, may install and operate, on its premises and on its side of the Point of Interconnection, one or more check meters to check Connecting Transmission Owner’s meters. Such check meters shall be for check purposes only and shall not be used for the measurement of power flows for purposes of this Agreement, except as provided in Article 7.4 below. The check meters shall be subject at all reasonable times to inspection and examination by Connecting Transmission Owner or its designee. The installation, operation and maintenance thereof shall be performed entirely by Developer in accordance with Good Utility Practice.

  • Delivery Point The delivery point is the point of delivery of the Power Product to the CAISO Controlled Grid (the “Delivery Point”). Seller shall provide and convey to Buyer the Power Product from the Generating Facility at the Delivery Point. Title to and risk of loss related to the Power Product transfer from Seller to Buyer at the Delivery Point.

Most Referenced Clauses

Most Referenced Definitions