Change of Preferred InterLATA or IntraLATA Carrier Sample Clauses

Change of Preferred InterLATA or IntraLATA Carrier. 33.9.2 SBC-13STATE shall accept and process the following types of preferred carrier changes sent by CLEC for end users subscribing to CLEC local service: (1) intraLATA toll, and (2) interLATA toll.
AutoNDA by SimpleDocs

Related to Change of Preferred InterLATA or IntraLATA Carrier

  • Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where InterGlobe has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to InterGlobe. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for InterGlobe (e.g. hairpinning):

  • CHANGE OF T-PIN The Account Holder may change his T-PIN from time to time in accordance with the Bank’s prescribed procedure then prevailing. The Bank shall be entitled, in its reasonable discretion but without liability and without giving any reason, to reject any selection made by the Account Holder as his substituted T-PIN; if the Bank so approves, such substituted T-PIN, shall take effect from the time of receipt by the Bank of such instructions from the Account Holder. The Account Holder shall take all steps not to select such numbers as a substitute T-PIN which may easily be ascertained or otherwise facilitate fraud or forgery.

  • wire Unbundled ISDN Digital Loops These will be provisioned according to industry standards for 2-Wire Basic Rate ISDN services and will come standard with a test point, OC, and a DLR. NewPhone will be responsible for providing BellSouth with a Service Profile Identifier (SPID) associated with a particular ISDN-capable Loop and customer. With the SPID, BellSouth will be able to adequately test the circuit and ensure that it properly supports ISDN service.

  • Wire Unbundled DS1 Digital Loop This is a designed 4-wire Loop that is provisioned according to industry standards for DS1 or Primary Rate ISDN services and will come standard with a test point, OC, and a DLR. A DS1 Loop may be provisioned over a variety of loop transmission technologies including copper, HDSL-based technology or fiber optic transport systems. It will include a 4-Wire DS1 Network Interface at the End User’s location.

  • Change of Vehicle 13.1 We reserve the right to substitute a comparable or superior Vehicle in extreme circumstances. This does not constitute a breach of contract and does not entitle You to any refund.

  • -wire Unbundled Digital/DS0 Loop These are designed 4-wire Loops that may be configured as 64kbps, 56kbps, 19kbps, and other sub-rate speeds associated with digital data services and will come standard with a test point, OC, and a DLR.

  • Reverse ADSL Loops If a CLEC’s ADSL Transmission Unit (including those integrated into DSLAMs) is attached to Sprint’s Network and if an ADSL Copper Loop should start at an outside location, and is looped through a host or remote, and then to the subscriber, the copper plant from the outside location to the Sprint host or remote central office must be a facility dedicated to ADSL transmission only and not part of Sprint’s regular feeder or distribution plant.

  • Change of Control of the Academy Trust 102A) The Secretary of State may at any time by notice in writing, subject to clause 102C) below, terminate this Agreement forthwith (or on such other date as he may in his absolute discretion determine) in the event that there is a change:

  • Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers.

  • Crossing of Picket Lines During Strike An Employee covered by this Agreement shall have the right to refuse to cross a picket line or to handle struck work arising out of Labour disputes. Failure to cross such a picket line or handle struck goods by a member of this Union shall not be considered a violation of this Agreement, nor shall it be grounds for disciplinary action. An Employee who is absent by reason of refusal to cross a picket line shall be paid at the discretion of the Employer.

Time is Money Join Law Insider Premium to draft better contracts faster.