Condition Based Monitoring (CBM) Sample Clauses

Condition Based Monitoring (CBM). On a monthly basis, the Contractor shall collect and review the information from their PT&I activities and from condition monitoring equipment installed throughout the CPS. The Contractor shall conduct a monthly meeting on or about the 20th of the month, with the Government’s System Managers to go over their most recent PT&I results and findings. The Contractor shall correct any minor problems found during the performance of this activity as soon as practical, the Contractor shall documented their findings in the CMMS and notify the COR. The Contractor shall partner with the Government in seeking PT&I process improvements and in performing corrective actions. The Contractor shall make all test data results available to the Government.
AutoNDA by SimpleDocs

Related to Condition Based Monitoring (CBM)

  • ADDITIONAL SPECIAL CONTRACT CONDITIONS Special Contract Conditions revisions: the corresponding subsections of the Special Contract Conditions referenced below are replaced in their entirety with the following:

  • Minimum Site Requirements for TIPS Sales (when applicable to TIPS Sale). Cleanup: When performing work on site at a TIPS Member’s property, Vendor shall clean up and remove all debris and rubbish resulting from their work as required or directed by the TIPS Member or as agreed by the parties. Upon completion of work, the premises shall be left in good repair and an orderly, neat, clean and unobstructed condition. Preparation: Vendor shall not begin a project for which a TIPS Member has not prepared the site, unless Vendor does the preparation work at no cost, or until TIPS Member includes the cost of site preparation in the TIPS Sale Site preparation includes, but is not limited to: moving furniture, installing wiring for networks or power, and similar pre‐installation requirements. Registered Sex Offender Restrictions: For work to be performed at schools, Vendor agrees that no employee of Vendor or a subcontractor who has been adjudicated to be a registered sex offender will perform work at any time when students are, or reasonably expected to be, present unless otherwise agreed by the TIPS Member. Vendor agrees that a violation of this condition shall be considered a material breach and may result in the cancellation of the TIPS Sale at the TIPS Member’s discretion. Vendor must identify any additional costs associated with compliance of this term. If no costs are specified, compliance with this term will be provided at no additional charge. Safety Measures: Vendor shall take all reasonable precautions for the safety of employees on the worksite, and shall erect and properly maintain all necessary safeguards for protection of workers and the public. Vendor shall post warning signs against all hazards created by the operation and work in progress. Proper precautions shall be taken pursuant to state law and standard practices to protect workers, general public and existing structures from injury or damage. Smoking: Persons working under Agreement shall adhere to the TIPS Member’s or local smoking statutes, codes, ordinances, and policies.

  • Unbundled Loop Modifications (Line Conditioning 2.5.1 Line Conditioning is defined as routine network modification that BellSouth regularly undertakes to provide xDSL services to its own customers. This may include the removal of any device, from a copper Loop or copper Subloop that may diminish the capability of the Loop or Subloop to deliver high-speed switched wireline telecommunications capability, including xDSL service. Such devices include, load coils, excessive bridged taps, low pass filters, and range extenders. Excessive bridged taps are bridged taps that serves no network design purpose and that are beyond the limits set according to industry standards and/or the BellSouth’s TR 73600 Unbundled Local Loop Technical Specification. 2.5.2 BellSouth will remove load coils only on copper Loops and Subloops that are less than eighteen thousand (18,000) feet in length. 2.5.3 For any copper loop being ordered by NewPhone which has over six thousand (6,000) feet of combined bridged tap will be modified, upon request from NewPhone, so that the loop will have a maximum of six thousand (6,000) feet of bridged tap. This modification will be performed at no additional charge to NewPhone. Loop conditioning orders that require the removal of bridged tap that serves no network design purpose on a copper Loop that will result in a combined total of bridged tap between two thousand five hundred (2,500) and six thousand (6,000) feet will be performed at the rates set forth in Exhibit A. 2.5.4 NewPhone may request removal of any unnecessary and non-excessive bridged tap (bridged tap between zero (0) and two thousand five hundred (2,500) feet which serves no network design purpose), at rates pursuant to BellSouth’s SC Process as mutually agreed to by the Parties. 2.5.5 Rates for ULM are as set forth in Exhibit A. 2.5.6 BellSouth will not modify a Loop in such a way that it no longer meets the technical parameters of the original Loop type (e.g., voice grade, ADSL, etc.) being ordered. 2.5.7 If NewPhone requests ULM on a reserved facility for a new Loop order, BellSouth may perform a pair change and provision a different Loop facility in lieu of the reserved facility with ULM if feasible. The Loop provisioned will meet or exceed specifications of the requested Loop facility as modified. NewPhone will not be charged for ULM if a different Loop is provisioned. For Loops that require a DLR or its equivalent, BellSouth will provide LMU detail of the Loop provisioned. 2.5.8 NewPhone shall request Loop make up information pursuant to this Attachment prior to submitting a service inquiry and/or a LSR for the Loop type that NewPhone desires BellSouth to condition. 2.5.9 When requesting ULM for a Loop that BellSouth has previously provisioned for NewPhone, NewPhone will submit a SI to BellSouth. If a spare Loop facility that meets the Loop modification specifications requested by NewPhone is available at the location for which the ULM was requested, NewPhone will have the option to change the Loop facility to the qualifying spare facility rather than to provide ULM. In the event that BellSouth changes the Loop facility in lieu of providing ULM, NewPhone will not be charged for ULM but will only be charged the service order charges for submitting an order.

  • Project Monitoring Reporting and Evaluation The Recipient shall furnish to the Association each Project Report not later than forty-five (45) days after the end of each calendar semester, covering the calendar semester.

  • How Do I Get More Information? This Notice summarizes the Action, the terms of the Settlements, and your rights and options in connection with the Settlements. More details are in the Settlement Agreements, which are available for your review at xxx.XxxxxxxxxXxxXxxxxxxxxXxxxxxxxxx.xxx. The Settlement Website also has the Second Amended Complaint and other documents relating to the Settlements. You may also call toll-free 0-000-000-0000 or write the Claims Administrator at: Financial Aid Antitrust Settlements, c/o Claims Administrator, 0000 Xxxx Xxxxxx, Xxxxx 0000, Xxxxxxxxxxxx, XX 00000. To: Settlement Class Member Email Address From: Claims Administrator Subject: Notice of Proposed Class Action Settlement – Xxxxx, et al. x. Xxxxx University, et al. Please visit xxx.XxxxxxxxxXxxXxxxxxxxxXxxxxxxxxx.xxx for more information. • The Court has preliminarily approved proposed settlements (“Settlements”) with the following ten schools: Brown University, the University of Chicago, the Trustees of Columbia University in the City of New York, Trustees of Dartmouth College, Duke University, Emory University, Northwestern University, Xxxxxxx Xxxxx Xxxx University, Vanderbilt University, and Yale University (collectively the “Settling Universities”). • The Court has also preliminarily approved a class of students who attended one or more of the Settling Universities during certain time periods. This is referred to as the “Settlement Class,” which is defined in more detail below.

  • SERVICE REQUIREMENTS FOR REFERRED CLIENTS A. Agent agrees to respond to any communications from a Referred Client within two (2) hours after receipt if such communication is received between 9:00am to 5:00pm local time. For communications received outside of these hours, Agent agrees to respond by 10:00am the next day. B. Agent agrees to update XXXX.xxx with status updates within 48 hours after initial communication with a Referred Client and upon every significant status change until closing or abandoned. Updates shall be made by Agent via email to xxxxxxxxxxxx@xxxx.xxx. C. Vacations or extended absences shall be reported, with length of pause, to XXXX.xxx via email to D. Agent will not add Referred Client to any email list or calling list without the express permission of Referred Client. E. Agent agrees XXXX.xxx has the right to survey the Referred Client at any time. F. If Agent is contacted by a Referred Client that Agent is unwilling or unable to assist, Agent shall direct such Referred Client back to XXXX.xxx for assistance and notify XXXX.xxx at xxxxxxxxxxxx@xxxx.xxx. G. Agent agrees that XXXX.xxx has no obligation to provide Agent with any number of referrals and that prospective clients are free to select the agent they wish to work with for any particular real estate transaction.

  • Meteorological Data Reporting Requirement (Applicable to wind generation facilities only)

  • Annual Reports on Assessment of Compliance with Servicing Criteria (a) On or before March 1 of each year commencing in March 2018, the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Operating Advisor and, if it has made (or is required to make) an Advance during the applicable calendar year, the Trustee, each at its own expense, shall furnish (and each of the preceding parties, as applicable, (i) with respect to any Servicing Function Participant of such party that is a Mortgage Loan Seller Sub-Servicer, shall use commercially reasonable efforts to cause such Servicing Function Participant to furnish, and (ii) with respect to any other Servicing Function Participant of such party (other than any party to this Agreement), shall cause such Servicing Function Participant to furnish) (each Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Operating Advisor, any Servicing Function Participant and, if it has made (or is required to make) an Advance during the applicable calendar year, the Trustee, as the case may be, a “Reporting Servicer”) to the Certificate Administrator, the Trustee, the Serviced Companion Loan Holders (or, in the case of a Serviced Companion Loan that is part of an Other Securitization Trust, the applicable Other Depositor and Other Exchange Act Reporting Party), the Operating Advisor (only in the case of a report furnished by the Special Servicer) and the Depositor, a report on an assessment of compliance with the Relevant Servicing Criteria (together with a copy thereof in XXXXX-Compatible Format, or in such other format as otherwise agreed upon by the Depositor, the Certificate Administrator, the applicable Other Depositor, the applicable Other Exchange Act Reporting Party and the applicable Certifying Servicer) that complies in all material respects with the requirements of Item 1122 of Regulation AB and contains (A) a statement by such Reporting Servicer of its responsibility for assessing compliance with the Relevant Servicing Criteria, (B) a statement that such Reporting Servicer used the Servicing Criteria to assess compliance with the Relevant Servicing Criteria, (C) such Reporting Servicer’s assessment of compliance with the Relevant Servicing Criteria as of the end of and for the preceding calendar year, including, if there has been any material instance of noncompliance with the Relevant Servicing Criteria, a discussion of each such failure and the nature and status thereof and (D) a statement that a registered public accounting firm has issued an attestation report on such Reporting Servicer’s assessment of compliance with the Relevant Servicing Criteria as of and for such period. Copies of all compliance reports delivered pursuant to this Section 10.09 shall be provided to any Certificateholder, upon the written request thereof, by the Certificate Administrator. Each such report shall be addressed to the Depositor and each Other Depositor (if addressed) and signed by an authorized officer of the applicable company, and shall address each of the Relevant Servicing Criteria specified on a certification substantially in the form of Exhibit O to this Agreement delivered to the Depositor on the Closing Date. Promptly after receipt of each such report, (i) the Depositor and each Other Depositor may review each such report and, if applicable, consult with the each Reporting Servicer as to the nature of any material instance of noncompliance with the Relevant Servicing Criteria, and (ii) the Certificate Administrator shall confirm that the assessments, taken individually address the Relevant Servicing Criteria for each party as set forth on Exhibit O to this Agreement and notify the Depositor of any exceptions. For the avoidance of doubt, the Trustee shall have no obligation or duty to determine whether any such report (other than any such report furnished by the Trustee or any Servicing Function Participant of the Trustee) is in form and substance in compliance with the requirements of Regulation AB. (b) On the Closing Date, the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Trustee and the Operating Advisor each acknowledge and agree that Exhibit O to this Agreement sets forth the Relevant Servicing Criteria for such party. (c) No later than the end of each fiscal year for the Trust, the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Operating Advisor and, if it has made (or is required to make) an Advance during such fiscal year, the Trustee shall notify the Certificate Administrator, the Depositor, each Other Exchange Act Reporting Party and each Other Depositor as to the name of each Servicing Function Participant utilized by it, and the Certificate Administrator shall notify the Depositor and each Other Depositor as to the name of each Servicing Function Participant utilized by it, during such fiscal year, and each such notice will specify what specific Servicing Criteria will be addressed in the report on assessment of compliance prepared by such Servicing Function Participant. When the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Trustee (if applicable), the Operating Advisor and any Servicing Function Participant submit their assessments pursuant to Section 10.09(a) of this Agreement, such parties will also at such time include the assessment (and related attestation pursuant to Section 10.10 of this Agreement) of each Servicing Function Participant engaged by it. The fiscal year for the Trust shall be January 1 through and including December 31 of each calendar year. (d) In the event the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Trustee (if it has made, or is required to make, an Advance during the applicable period) or the Operating Advisor is terminated or resigns pursuant to the terms of this Agreement, such party shall provide, and each such party shall cause (or, if the Servicing Function Participant is a Mortgage Loan Seller Sub-Servicer, shall use commercially reasonable efforts to cause) any Servicing Function Participant of such party to provide (and the Master Servicer, the Special Servicer and the Certificate Administrator shall, with respect to any Servicing Function Participant that resigns or is terminated under any applicable servicing agreement, cause such Servicing Function Participant (or, in the case of each Servicing Function Participant that is a Mortgage Loan Seller Sub-Servicer, shall use commercially reasonable efforts to cause such Servicing Function Participant) to provide) an annual assessment of compliance pursuant to this Section 10.09, coupled with an attestation as required in Section 10.10 of this Agreement with respect to the period of time that the Master Servicer, the Special Servicer, the Certificate Administrator, the Custodian, the Trustee (if it has made, or is required to make, an Advance during such period of time) or the Operating Advisor was subject to this Agreement or the period of time that the applicable Servicing Function Participant was subject to such other servicing agreement. With respect to each Outside Serviced Mortgage Loan serviced under the applicable Outside Servicing Agreement, the Certificate Administrator shall use commercially reasonable efforts to obtain, and upon receipt deliver to the Depositor, an annual report on assessment of compliance as described in this Section and an attestation as described in Section 10.10 from the related Outside Servicer, Outside Special Servicer, Outside Custodian, Outside Trustee and Outside Paying Agent or Outside Certificate Administrator and in form and substance similar to the annual report on assessment of compliance described in this Section 10.09 and the attestation described in Section 10.10.

  • Evaluation, Testing, and Monitoring 1. The System Agency may review, test, evaluate and monitor Grantee’s Products and services, as well as associated documentation and technical support for compliance with the Accessibility Standards. Review, testing, evaluation and monitoring may be conducted before and after the award of a contract. Testing and monitoring may include user acceptance testing. Neither the review, testing (including acceptance testing), evaluation or monitoring of any Product or service, nor the absence of review, testing, evaluation or monitoring, will result in a waiver of the State’s right to contest the Grantee’s assertion of compliance with the Accessibility Standards. 2. Grantee agrees to cooperate fully and provide the System Agency and its representatives timely access to Products, records, and other items and information needed to conduct such review, evaluation, testing, and monitoring.

  • Commercial Operation Date Testing and Modifications Prior to the Commercial Operation Date, the Connecting Transmission Owner shall test the Connecting Transmission Owner’s Attachment Facilities and System Upgrade Facilities and System Deliverability Upgrades and Developer shall test the Large Generating Facility and the Developer Attachment Facilities to ensure their safe and reliable operation. Similar testing may be required after initial operation. Developer and Connecting Transmission Owner shall each make any modifications to its facilities that are found to be necessary as a result of such testing. Developer shall bear the cost of all such testing and modifications. Developer shall generate test energy at the Large Generating Facility only if it has arranged for the injection of such test energy in accordance with NYISO procedures.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!