Continuous Emission Monitor Systems Sample Clauses

Continuous Emission Monitor Systems. The Bureau considers continuous emission monitor systems (“CEMS”) another very important means of determining and insuring compliance with emission limits at Maine’s larger facilities. Maine’s CEMS program is based on DEP Rule Chapter 117, Source Surveillance which incorporates sections of 40 CFR Parts 51 and 60. In general all fuel burning equipment with a heat input capacity of greater than 100 million British Thermal Units and sources required by New Source Performance Standards to install and operate CEMS. The Bureau requires that these sources conduct quarterly Cylinder Gas Audits, and annual Relative Accuracy Test Audits or Relative Accuracy Audits for gaseous CEMS. Opacity monitors are required to undergo quarterly performance audits and annual drift tests. Facilities submit the results of these tests to the compliance inspectors for their review, and inspectors regularly observe the audits. Compliance inspectors review all quarterly continuous emission monitoring reports for compliance and respond to all unusual incidents of monitor downtime or excess emissions within the quarter they are submitted. Problems will be brought to the attention of the Enforcement Unit. Thirty facilities are required to operate CEMS. As in previous years, all facilities with CEMS will be inspected. CEMS reports are recorded in EPA’s PC-CEMS computer program and reviewed periodically for problems and trends. Related EPA Priorities: Review CEM reports and observe audits MEASURES OF SUCCESS ➢ Cumulative number of test observations in AFS. ➢ Number of records in PC-CEMS
Sample 1
AutoNDA by SimpleDocs

Related to Continuous Emission Monitor Systems

  • ACCESS TO OPERATIONS SUPPORT SYSTEMS 2.1 BellSouth shall provide Max-Tel access to operations support systems (“OSS”) functions for pre-ordering, ordering and provisioning, maintenance and repair, and billing. BellSouth shall provide access to the OSS through manual and/or electronic interfaces as described in this Attachment. It is the sole responsibility of Max-Tel to obtain the technical capability to access and utilize BellSouth’s OSS interfaces. Specifications for Max-Tel ’s access and use of BellSouth’s electronic Version R4Q01: 12/01/01 interfaces are set forth at xxx.xxxxxxxxxxxxxxx.xxxxxxxxx.xxx and are incorporated herein by reference.

  • Network Resource Interconnection Service (check if selected)

  • Infrastructure Vulnerability Scanning Supplier will scan its internal environments (e.g., servers, network devices, etc.) related to Deliverables monthly and external environments related to Deliverables weekly. Supplier will have a defined process to address any findings but will ensure that any high-risk vulnerabilities are addressed within 30 days.

  • Verizon Operations Support Systems Verizon systems for pre- ordering, ordering, provisioning, maintenance and repair, and billing.

  • Energy Resource Interconnection Service (ER Interconnection Service).

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • System Access CUSTOMER agrees to provide to PROVIDER, at CUSTOMER’S expense, necessary access to the mainframe computer and related information technology systems (the “System”) on which CUSTOMER data is processed during the times (the “Service Hours”) specified in the PSAs, subject to reasonable downtime for utility outages, maintenance, performance difficulties and the like. In the event of a change in the Service Hours, CUSTOMER will provide PROVIDER with at least fifteen (15) calendar days written notice of such change.

  • Non-Synchronous Generation The Interconnection Customer shall design its Small Generating Facility to maintain a composite power delivery at continuous rated power output at the high-side of the generator substation at a power factor within the range of 0.95 leading to 0.95 lagging, unless the NYISO or the Transmission Owner in whose Transmission District the Small Generating Facility interconnects has established a different power factor range that applies to all similarly situated non-synchronous generators in the control area or Transmission District (as applicable) on a comparable basis, in accordance with Good Utility Practice. This power factor range standard shall be dynamic and can be met using, for example, power electronics designed to supply this level of reactive capability (taking into account any limitations due to voltage level, real power output, etc.) or fixed and switched capacitors, or a combination of the two. This requirement shall only apply to newly interconnecting non-synchronous generators that have not yet executed a Facilities Study Agreement as of September 21, 2016.

  • CUSTOMER SERVICE ACCESS The Competitive Supplier agrees to provide, or cause to be provided, certain customer services to Participating Consumers. Such services shall be reasonably accessible to all Participating Consumers, shall be available during normal working hours, shall allow Participating Consumers to transact business they may have with the Competitive Supplier, and shall serve as a communications liaison among the Competitive Supplier, the Town, and the Local Distributor. A toll-free telephone number will be established by Competitive Supplier and be available for Participating Consumers to contact Competitive Supplier during normal business hours (9:00 A.M. - 5:00 P.M. Eastern Standard Time, Monday through Friday) to resolve concerns, answer questions and transact business with respect to the service received from Competitive Supplier. The Town will post program-related information on the Town’s website which will be available to Participating Consumers for general information, product and service information, and other purposes.

Time is Money Join Law Insider Premium to draft better contracts faster.