Common use of copper pipes Clause in Contracts

copper pipes. Pipes shall be hard drawn and half-hard pipes of the class stated. Class 0 (thin walled hard drawn) pipes shall not be bent. Class 1 (thin walled half- hard), class 2 (half-hard) and class 3 (heavy walled half-hard) pipes shall only be bent with benders with inner and outer formers. Fittings to copper waste, vent and anti-syphon pipes, capillary solder fittings and compression fittings shall be "Cobra Watertech" type. Capillary solder fittings shall comply with ISO 2016. Only compression fittings shall be used in walls or in ground All soldered joints shall be wiped and brass unions shall be used for jointing lead to steel Where fittings have reducing ends or branches they are described as "reducing". In the case of pipes with diameters not exceeding 60mm only the largest end or branch size is given. Should the contractor wish to use other fittings and bushes or reducers he may do so on the understanding that no claim in this regard will be entertained. In the case of pipes with diameters exceeding 60mm all sizes are given and no claim for extra bushes, reducers, etc will be entertained Descriptions of gutter outlets etc shall be deemed to include wire balloon gratings Descriptions of septic tanks shall be deemed to include excavation, bedding and jointing, concrete base slabs, jointing to drains and backfilling, compaction, etc all in accordance with the manufacturer's instructions Exposed surfaces of concrete stormwater channels, cover slabs, inspection eye marker slabs, xxxxxx tops, cleaning eye tops, catchpits, inspection xxxxxxxx, etc shall be finished smooth with plaster No claim for rock excavation will be entertained unless the contractor has timeously notified the quantity surveyor thereof prior to backfilling "Soft rock" and "hard rock" shall be as defined in "Earthworks" Pipes shall be laid and bedded and trenches shall be carefully backfilled in accordance with manufacturers' instructions Where no manufacturers' instructions exist pipes shall be laid in accordance with clauses 5.1 and 5.2 of each of the following: SABS 1200 L : Medium- pressure pipelines LD : Sewers LE : Stormwater drainage Pipe trenches etc shall be backfilled in accordance with clauses 3, 5.5, 5.6, 5.7 and 7 of SABS 1200 DB : Earthworks (Pipe trenches) Pipes shall be bedded in accordance with clauses 3.1 to 3.4.1,

copper pipes. Pipes shall be hard drawn and half-hard pipes of the class stated. Class 0 (thin walled hard drawn) pipes shall not be bent. Class 1 (thin walled half- half-hard), class 2 (half-hard) and class 3 (heavy walled half-hard) pipes shall only be bent with benders with inner and outer formers. Fittings to copper waste, vent and anti-syphon pipes, capillary solder fittings and compression fittings shall be "Cobra Watertech" type. Capillary solder fittings shall comply with ISO 2016. Only compression fittings shall be used in walls or in ground All soldered joints Unless specifically otherwise stated, descriptions of pipes shall be wiped and brass unions shall be used for jointing lead deemed to steel include fixing to walls etc, casting in, building in or suspending not exceeding 1m below suspension level Where fittings have reducing ends or branches they are described as "reducing". In the case of pipes with diameters not exceeding 60mm only the largest end or branch size is given. Should the contractor wish to use other fittings and bushes or reducers he may do so on the understanding that no claim in this regard will be entertained. In the case of pipes with diameters exceeding 60mm all sizes are given and no claim for extra bushes, reducers, etc will be entertained Flush pans shall have straight or side outlets and "P" or "S" traps as necessary Stainless steel basins, sinks, wash troughs, urinals, etc. Units shall have standard aprons on all exposed edges and tiling keys against walls where applicable Descriptions of gutter outlets etc waste unions shall be deemed to include wire balloon gratings Descriptions of septic tanks shall be deemed rubber or vulcanite plugs and chains fixed to include excavationfittings Section No. 2 Bill No. 13 PLUMBING AND DRAINAGE 1 50mm Pipes fixed to walls, bedding and jointingetc. m 27 2 110mm Pipes fixed to walls, concrete base slabs, jointing to drains and backfilling, compaction, etc all in accordance with the manufacturer's instructions Exposed surfaces of concrete stormwater channels, cover slabs, inspection eye marker slabs, xxxxxx tops, cleaning eye tops, catchpits, inspection xxxxxxxx, etc shall be finished smooth with plaster No claim for rock excavation will be entertained unless the contractor has timeously notified the quantity surveyor thereof prior to backfilling "Soft rock" and "hard rock" shall be as defined in "Earthworks" Pipes shall be laid and bedded and trenches shall be carefully backfilled in accordance with manufacturers' instructions Where no manufacturers' instructions exist pipes shall be laid in accordance with clauses 5.1 and 5.2 of each of the following: SABS 1200 L : Medium- pressure pipelines LD : Sewers LE : Stormwater drainage Pipe trenches etc shall be backfilled in accordance with clauses 3, 5.5, 5.6, 5.7 and 7 of SABS 1200 DB : Earthworks (Pipe trenches) Pipes shall be bedded in accordance with clauses 3.1 to 3.4.1,etc. m 5

copper pipes. Pipes shall be hard hard-drawn and half-hard pipes of the class stated. Class 0 (thin walled hard drawn) pipes shall not be bent. Class 1 (thin walled half- half-hard), class 2 (half-hard) and class 3 (heavy walled half-hard) pipes shall only be bent with benders with inner and outer formers. Fittings to copper waste, vent and anti-syphon pipes, capillary solder fittings and compression fittings shall be "Cobra Watertech" Approved type. Capillary solder fittings shall comply with ISO 2016. Only compression fittings shall be used in walls or in ground ground. Fixing of pipes Unless specifically otherwise stated, descriptions of pipes shall be deemed to include fixing to walls, etc., casting-in, building-in or suspending not exceeding 1m below suspension level. Lead pipes and fittings All soldered joints shall be wiped and brass unions shall be used for jointing lead to steel steel. Reducing fittings Where fittings have reducing ends or branches they are described as "reducing". In the case of pipes with diameters not exceeding 60mm mm, only the largest end or branch size is given. Should the contractor wish to use other fittings and bushes or reducers reducers, he may do so on the understanding that no claim in this regard will be entertained. In the case of pipes with diameters exceeding 60mm mm, all sizes are given and no claim for extra bushes, reducers, etc etc. will be entertained entertained. Wire gratings Descriptions of gutter outlets etc outlets, etc. shall be deemed to include wire balloon gratings gratings. Septic tanks Descriptions of septic tanks shall be deemed to include excavation, bedding and jointing, concrete base slabs, jointing to drains and backfilling, compaction, etc etc. all in accordance with the manufacturer's instructions instructions. Carried forward Xxxx Xx. 12 PLUMBING AND DRAINAGE R Exposed concrete surfaces Exposed surfaces of concrete stormwater channels, cover slabs, inspection eye marker slabs, xxxxxx tops, cleaning eye tops, catchpits, inspection xxxxxxxx, etc etc. shall be finished smooth with plaster plaster. Excavations No claim for rock excavation will be entertained unless the contractor has timeously notified the quantity surveyor thereof prior to backfilling backfilling. "Soft rock" and "hard rock" shall be as defined in "Earthworks" Pipes shall be laid and bedded and trenches shall be carefully backfilled in accordance with manufacturers' instructions Where no manufacturers' instructions exist pipes shall be laid in accordance with clauses 5.1 and 5.2 of each of the following: SABS 1200 L : Medium- pressure pipelines LD : Sewers LE : Stormwater drainage Pipe trenches etc shall be backfilled in accordance with clauses 3, 5.5, 5.6, 5.7 and 7 of SABS 1200 DB : Earthworks (Pipe trenches) Pipes shall be bedded in accordance with clauses 3.1 to 3.4.1,".