Design for recycling Sample Clauses

Design for recycling. For all product models first placed on the EU market after 1 January 2012: • Plastic parts >100 g shall be manually separable into recyclable plastic streams with commonly available tools. • Product shall utilize commonly used fasteners for joining components, subassemblies, chassis and enclosures. • Non-separable connections (e.g. glued, welded) between different materials shall be avoided unless they are technically or legally required. • Product plastics shall be marked by material type (ISO 11469 referring ISO 1043, resin identification code, SPI, DIN, or country specific). Marking requirement does not apply to plastic parts weighing less than 25 g or with surface area less than 50 cm²; tape; plastic protective and stretch wraps and labels; or plastic pieces when due to shape marking is not possible. Exempted are plastic parts contained in reused complex modules. An exemption from the criteria in sections 5.1 and 5.2 will be acceptable for models that are sold in small numbers (less than 5,000 units per year), on the ground that the cost of implementing the criteria is disproportionate to the sales of the product. Exceptions should be reported to the Independent Inspector (see Annex C for reporting template).
AutoNDA by SimpleDocs
Design for recycling. 7.2.1 For all Products: a) Plastic parts >100 g shall be manually separable into recyclable plastic streams with Commonly Available Tools
Design for recycling. 5.2.1 Design for recycling for hardware For all Products: • Plastic parts >100 g shall be manually separable into recyclable plastic streams with Commonly Available Tools • Product shall utilize Commonly Used Fasteners for joining components, subassemblies, chassis and enclosures • Non-separable connections (e.g. glued, welded) between different materials shall be avoided unless they are technically or legally required • Product plastics shall be marked by material type (ISO 11469 referring ISO 1043, resin identification code, SPI, DIN, or country specific). Marking requirement does not apply to plastic parts weighing less than 25 g or with surface area less than 50 cm²; tape; plastic protective and stretch wraps and labels; or plastic pieces when marking is not possible due to shape. Plastic parts contained in reused complex modules are exempted. 5.2.2 Design for dismantling for recycling and recovery for hardware: Signatories shall ensure that joining, fastening or sealing techniques do not prevent access to the following components (when present) in a non-destructive extraction method without requiring proprietary or not Commonly Available Tools: • Batteries • Printed circuit boards greater than 10 cm² • Ink and toner Cartridges • Plastic containing brominated flame retardants • Liquid crystal displays greater than 100 cm² • External electric cables • Electrolyte capacitors containing substances of concern (height > 25 mm, diameter > 25 mm or proportionately similar volume) Accessing such components shall be facilitated by Signatories documenting the sequence of dismantling operations needed to access the targeted components, i.e. each of these operations, the type and the number of joining, fastening and sealing

Related to Design for recycling

  • Selection of Subcontractors, Procurement of Materials and Leasing of Equipment The contractor shall not discriminate on the grounds of race, color, religion, sex, national origin, age or disability in the selection and retention of subcontractors, including procurement of materials and leases of equipment. The contractor shall take all necessary and reasonable steps to ensure nondiscrimination in the administration of this contract. a. The contractor shall notify all potential subcontractors and suppliers and lessors of their EEO obligations under this contract. b. The contractor will use good faith efforts to ensure subcontractor compliance with their EEO obligations.

  • Solicitations for Subcontracts, Including Procurement of Materials and Equipment In all solicitations either by competitive bidding or negotiation made by the Local Government for work to be performed under a subcontract, including procurement of materials or leases of equipment, each potential subcontractor or supplier will be notified by the Local Government of the Local Government’s obligations under this Agreement and the Acts and Regulations relative to Nondiscrimination on the grounds of race, color, or national origin.

  • Procurement of Small Works Works estimated to cost $250,000 equivalent or less per contract, up to an aggregate amount not to exceed $800,000 equivalent, may be procured under lump-sum, fixed-price contracts awarded on the basis of quotations obtained from three (3) qualified domestic contractors in response to a written invitation. The invitation shall include a detailed description of the works, including basic specifications, the required completion date, a basic form of agreement acceptable to the Bank, and relevant drawings, where applicable. The award shall be made to the contractor who offers the lowest price quotation for the required work, and who has the experience and resources to complete the contract successfully. Part D: Review by the Bank of Procurement Decisions

  • Contractor Licensing, etc. Notwithstanding Section 14.c, District may terminate this Contract immediately by written notice to Contractor upon denial, suspension, revocation, or non-renewal of any license, permit, or certificate that Contractor must hold to provide services under this Contract.

  • Design Development An interim step in the design process. Design Development documents consist of plans, elevations, and other drawings and outline specifications. These documents will fix and illustrate the size and character of the entire project in its essentials as to kinds of materials, type of structure, grade elevations, sidewalks, utilities, roads, parking areas, mechanical and electrical systems, and such other work as may be required.

  • LIMITATIONS ON REVERSE ENGINEERING, DECOMPILATION AND DISASSEMBLY You may not reverse engineer, decompile, or disassemble the Software, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

  • Design XXX XXX XXXXX Plan and Aligned Budget

  • Removal of a General Partner (a) Upon the occurrence of an Event of Bankruptcy as to, or the dissolution of, a General Partner, such General Partner shall be deemed to be removed automatically; provided, however, that if a General Partner is on the date of such occurrence a partnership, the withdrawal, death or dissolution of, Event of Bankruptcy as to, or removal of, a partner in, such partnership shall be deemed not to be a dissolution of the General Partner if the business of such General Partner is continued by the remaining partner or partners. The Limited Partners may not remove the General Partner, with or without cause. (b) If a General Partner has been removed pursuant to this Section 7.4 and the Partnership is continued pursuant to Section 7.3 hereof, such General Partner shall promptly transfer and assign its General Partnership Interest in the Partnership to the substitute General Partner approved by a majority in interest of the Limited Partners in accordance with Section 7.3(b) hereof and otherwise admitted to the Partnership in accordance with Section 7.2 hereof. At the time of assignment, the removed General Partner shall be entitled to receive from the substitute General Partner the fair market value of the General Partnership Interest of such removed General Partner as reduced by any damages caused to the Partnership by such General Partner. Such fair market value shall be determined by an appraiser mutually agreed upon by the General Partner and a majority in interest of the Limited Partners within ten (10) days following the removal of the General Partner. In the event that the parties are unable to agree upon an appraiser, the removed General Partner and a majority in interest of the Limited Partners each shall select an appraiser. Each such appraiser shall complete an appraisal of the fair market value of the removed General Partner’s General Partnership Interest within thirty (30) days of the General Partner’s removal, and the fair market value of the removed General Partner’s General Partnership Interest shall be the average of the two appraisals; provided, however, that if the higher appraisal exceeds the lower appraisal by more than 20% of the amount of the lower appraisal, the two appraisers, no later than forty (40) days after the removal of the General Partner, shall select a third appraiser who shall complete an appraisal of the fair market value of the removed General Partner’s General Partnership Interest no later than sixty (60) days after the removal of the General Partner. In such case, the fair market value of the removed General Partner’s General Partnership Interest shall be the average of the two appraisals closest in value. (c) The General Partnership Interest of a removed General Partner, until transfer under Section 7.4(b), shall be converted to that of a special Limited Partner; provided, however, such removed General Partner shall not have any rights to participate in the management and affairs of the Partnership, and shall not be entitled to any portion of the income, expense, profit, gain or loss allocations or cash distributions allocable or payable, as the case may be, to the Limited Partners. Instead, such removed General Partner shall receive and be entitled only to retain distributions or allocations of such items that it would have been entitled to receive in its capacity as General Partner, until the transfer is effective pursuant to Section 7.4(b). (d) All Partners shall have given and hereby do give such consents, shall take such actions and shall execute such documents as shall be legally necessary, desirable and sufficient to effect all the foregoing provisions of this Section.

  • Manufacturing (a) The Supplier shall without limitation be responsible, at no additional cost to the Purchaser, for: sourcing and procuring all raw materials for the Products; obtaining all necessary approvals, permits and licenses for the manufacturing of the Products; providing sufficient qualified staff and workers to perform the obligations under this Purchase Agreement; implementing and maintaining effective inventory and production control procedures with respect to the Products; and handling other matters as reasonably requested by the Purchaser from time to time. (b) The Supplier shall not change any process, material, component, packaging or manufacturing location without the Purchaser’s express prior written approval.

  • Removal of General Partner (a) Upon the occurrence of an Event of Bankruptcy as to, or the dissolution of, the General Partner, the General Partner shall be deemed to be removed automatically; provided, however, that if the General Partner is on the date of such occurrence a partnership, the withdrawal, death, dissolution, Event of Bankruptcy as to or removal of a partner in such partnership shall be deemed not to be a dissolution of the General Partner if the business of the General Partner is continued by the remaining partner or partners. The Limited Partners may not remove the General Partner, with or without cause. (b) If the General Partner has been removed pursuant to this Section 7.04 and the Partnership is continued pursuant to Section 7.03, the General Partner shall promptly transfer and assign its General Partnership Interest in the Partnership to the substitute General Partner approved by a Majority in Interest in accordance with Section 7.03(b) and otherwise be admitted to the Partnership in accordance with Section 7.02. At the time of assignment, the removed General Partner shall be entitled to receive from the substitute General Partner the fair market value of the General Partnership Interest of such removed General Partner as reduced by any damages caused to the Partnership by such General Partner. Such fair market value shall be determined by an appraiser mutually agreed upon by the General Partner and a Majority in Interest (excluding the General Partner and any Subsidiary of the General Partner) within ten days following the removal of the General Partner. In the event that the parties are unable to agree upon an appraiser, the removed General Partner and a Majority in Interest (excluding the General Partner and any Subsidiary of the General Partner) each shall select an appraiser. Each such appraiser shall complete an appraisal of the fair market value of the removed General Partner’s General Partnership Interest within 30 days of the General Partner’s removal, and the fair market value of the removed General Partner’s General Partnership Interest shall be the average of the two appraisals; provided, however, that if the higher appraisal exceeds the lower appraisal by more than 20% of the amount of the lower appraisal, the two appraisers, no later than 40 days after the removal of the General Partner, shall select a third appraiser who shall complete an appraisal of the fair market value of the removed General Partner’s General Partnership Interest no later than 60 days after the removal of the General Partner. In such case, the fair market value of the removed General Partner’s General Partnership Interest shall be the average of the two appraisals closest in value. (c) The General Partnership Interest of a removed General Partner, during the time after default until transfer under Section 7.04(b), shall be converted to that of a special Limited Partner; provided, however, such removed General Partner shall not have any rights to participate in the management and affairs of the Partnership, and shall not be entitled to any portion of the income, expense, profit, gain or loss allocations or cash distributions allocable or payable, as the case may be, to the Limited Partners. Instead, such removed General Partner shall receive and be entitled only to retain distributions or allocations of such items that it would have been entitled to receive in its capacity as General Partner, until the transfer is effective pursuant to Section 7.04(b). (d) All Partners shall have given and hereby do give such consents, shall take such actions and shall execute such documents as shall be legally necessary and sufficient to effect all the foregoing provisions of this Section 7.04.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!