Drawing Conventions
Drawing Conventions Sample Clauses
Related to Drawing Conventions
Union Conventions Subject to the approval of the supervisor(s) concerned, and upon written request submitted at least twenty (20) working days in advance, leave of absence without pay shall be granted to not more than two (2) employees at any one time, who may be elected or selected by the Union to attend any authorized labour convention. Such leave of absence is to be confined to the actual duration of the convention and the necessary travelling time. Such leave shall not exceed ten (10) working days per year for each employee to whom such leave is granted.
Conventions For purposes of this Article XIII, Party A means the Carrier from which a telephone number is Ported, and Party B means the carrier to which a telephone number is ported.
File Naming Conventions Files will be named according to the following convention: {gTLD}_{YYYY-MM-DD}_{type}_S{#}_R{rev}.{ext} where: {gTLD} is replaced with the gTLD name; in case of an IDN-TLD, the ASCII-compatible form (A-Label) must be used; {YYYY-MM-DD} is replaced by the date corresponding to the time used as a timeline watermark for the transactions; i.e. for the Full Deposit corresponding to 2009-08-02T00:00Z, the string to be used would be “2009-08-02”; {type} is replaced by: “full”, if the data represents a Full Deposit; “diff”, if the data represents a Differential Deposit; “thin”, if the data represents a Bulk Registration Data Access file, as specified in Section 3 of Specification 4; {#} is replaced by the position of the file in a series of files, beginning with “1”; in case of a lone file, this must be replaced by “1”. {rev} is replaced by the number of revision (or resend) of the file beginning with “0”: {ext} is replaced by “sig” if it is a digital signature file of the quasi-homonymous file. Otherwise it is replaced by “ryde”.
Measurements and arithmetic conventions All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Other Methods of Procurement of Goods and Works. The following table specifies the methods of procurement, other than International Competitive Bidding, which may be used for goods and works. The Procurement Plan shall specify the circumstances under which such methods may be used: (a) National Competitive Bidding (b) Shopping (c) Direct Contracting
Other Methods of Procurement of Goods and Works The following table specifies the methods of procurement, other than International Competitive Bidding, which may be used for goods and works. The Procurement Plan shall specify the circumstances under which such methods may be used: (a) National Competitive Bidding (b) Shopping (c) Direct Contracting
Particular Methods of Procurement of Goods Works and Services (other than Consultants’ Services)
Particular Methods of Procurement of Goods and Works International Competitive Bidding. Goods and works shall be procured under contracts awarded on the basis of International Competitive Bidding.
Protocols Each party hereby agrees that the inclusion of additional protocols may be required to make this Agreement specific. All such protocols shall be negotiated, determined and agreed upon by both parties hereto.
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
