Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).
Components Patheon will purchase and test all Components (with the exception of Client-Supplied Components) at Patheon’s expense and as required by the Specifications.
Borrower Information Used to Determine Applicable Interest Rates The parties understand that the applicable interest rate for the Obligations and certain fees set forth herein may be determined and/or adjusted from time to time based upon certain financial ratios and/or other information to be provided or certified to the Lenders by the Borrower (the “Borrower Information”). If it is subsequently determined that any such Borrower Information was incorrect (for whatever reason, including without limitation because of a subsequent restatement of earnings by the Borrower) at the time it was delivered to the Administrative Agent, and if the applicable interest rate or fees calculated for any period were lower than they should have been had the correct information been timely provided, then, such interest rate and such fees for such period shall be automatically recalculated using correct Borrower Information. The Administrative Agent shall promptly notify the Borrower in writing of any additional interest and fees due because of such recalculation, and the Borrower shall pay such additional interest or fees due to the Administrative Agent, for the account of each Lender, within five (5) Business Days of receipt of such written notice. Any recalculation of interest or fees required by this provision shall survive the termination of this Agreement, and this provision shall not in any way limit any of the Administrative Agent’s, the Issuing Bank’s, or any Lender’s other rights under this Agreement.
Changes to Specifications All Specifications and any changes thereto agreed to by the parties from time to time shall be in writing, dated and signed by the parties. Any change to the Process shall be deemed a Specification change. No change in the Specifications shall be implemented by Catalent, whether requested by Client or requested or required by any Regulatory Authority, until the parties have agreed in writing to such change, the implementation date of such change, and any increase or decrease in costs, expenses or fees associated with such change (including any change to Unit Pricing). Catalent shall respond promptly to any request made by Client for a change in the Specifications, and both parties shall use commercially reasonable, good faith efforts to agree to the terms of such change in a timely manner. As soon as possible after a request is made for any change in Specifications, Catalent shall notify Client of the costs associated with such change and shall provide such supporting documentation as Client may reasonably require. Client shall pay all costs associated with such agreed upon changes. If there is a conflict between the terms of this Agreement and the terms of the Specifications, this Agreement shall control. Catalent reserves the right to postpone effecting changes to the Specifications until such time as the parties agree to and execute the required written amendment.
Temperature The Committed Gas shall not have a temperature of less than forty degrees Fahrenheit (40°F) nor more than one hundred twenty degrees Fahrenheit (120°F).
Compatibility The Spacecraft Bus shall be compatible with standard GPS interfaces as defined in [**Redacted**].
Computational Materials and Structural Term Sheets (a) Not later than 10:30 a.m., New York time, on the business day before the date on which the Current Report relating to the Offered Certificates of a Series is required to be filed by the Company with the Commission pursuant to Section 5(b) hereof, the Underwriter shall deliver to the Company five complete copies of all materials provided by the Underwriter to prospective investors in such Offered Certificates that constitute (i) "Computational Materials" within the meaning of the no-action letter dated May 20, 1994 issued by the Division of Corporation Finance of the Commission to Xxxxxx, Xxxxxxx Acceptance Corporation I, Xxxxxx, Peabody & Co. Incorporated, and Xxxxxx Structured Asset Corporation and the no-action letter dated May 27, 1994 issued by the Division of Corporation Finance of the Commission to the Public Securities Association (together, the "Xxxxxx Letters"), the filing of which material is a condition of the relief granted in such letter (such materials being the "Computational Materials"), and (ii) "Structural Term Sheets" within the meaning of the no-action letter dated February 17, 1995 issued by the Division of Corporation Finance of the Commission to the Public Securities Association (the "PSA Letter"), the filing of which material is a condition of the relief granted in such letter (such materials being the "Structural Term Sheets"). Each delivery of Computational Materials and Structural Term Sheets to the Company pursuant to this paragraph (a) shall be effected by delivering four copies of such materials to counsel for the Company on behalf of the Company at the address specified in Section 3 hereof and one copy of such materials to the Company.
Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.
Configuration The configuration for the Purchase Right Aircraft will be the Detail Specification for Model 767-3S2F aircraft at the revision level in effect at the time of the Supplemental Agreement. Such Detail Specification will be revised to include (i) changes required to obtain required regulatory certificates and (ii) other changes as mutually agreed upon by Boeing and Customer.
Spares Boeing will revise, as applicable, the customized Recommended Spares Parts List (RSPL) and Illustrated Parts Catalog (IPC).
