Float and Displacement Sample Clauses

Float and Displacement. Displacement type will be used for clean liquid applications up to 1219 mm (48 inches). External displacer cages, segregated from vessels by block valves shall be used. External displacer cages will be supplied with 2 inch minimum flange side and bottom connections and rotatable heads. 4 inch top mounted displacers shall be used where side and bottom type is unsuitable and shall have a stilling well of the diameter as the vessel nozzle. The xxxxxxxx shall have isolation as well as vents and drain valves. Displacement type instruments will be used up to 1219 mm and where the operating temperature is above 0C. For temperatures lower than 0C, even for measurements up to 1219 mm, a DP transmitter shall be selected to minimize the effect of liquid boiling and to obtain a stable measurement. For high temperature, compensation due to density changes shall be calculated to obtain the true level. For interface, special consideration will be given to displacer diameter to ensure sensitivity. Ultrasonic type instruments may also be considered. Electrical switch contacts shall be sealed snap acting micro-switch (single pole, double throw 24 VDC. Mercury bottle type switches shall not be used. Liquid level switches shall be used for alarms, interlocks, and not for ESD systems. Transmitters shall be used for ESD systems. For high temperature (higher than 200C) as well as low temperature (lower than 0C), insulation extension or torque tube extension shall be applied. Guided wave radar / displacer shall be used for interface liquid level measurement.
AutoNDA by SimpleDocs

Related to Float and Displacement

  • Retention and disposal 9.5.1. Information shared under this Agreement will be securely stored and disposed by secure means when no longer required for the purpose for which it is provided as per each parties’ Information Security Policy, unless otherwise agreed in a specific case, and legally permitted. Each party will determine and maintain their own retention schedule.

  • Reduction and Disconnection NYISO or Transmission Owner may reduce Network Access Interconnection Service or disconnect the Large Generating Facility or the Developer Attachment Facilities, when such, reduction or disconnection is necessary under Good Utility Practice due to an Emergency State. These rights are separate and distinct from any right of Curtailment of NYISO pursuant to the NYISO OATT. When NYISO or Transmission Owner can schedule the reduction or disconnection in advance, NYISO or Transmission Owner shall notify Developer of the reasons, timing and expected duration of the reduction or disconnection. NYISO or Transmission Owner shall coordinate with the Developer using Good Utility Practice to schedule the reduction or disconnection during periods of least impact to the Developer and the New York State Transmission System. Any reduction or disconnection shall continue only for so long as reasonably necessary under Good Utility Practice. The Parties shall cooperate with each other to restore the Large Generating Facility, the Attachment Facilities, and the New York State Transmission System to their normal operating state as soon as practicable consistent with Good Utility Practice.

  • Access and Disconnection 4.1 Distribution Licensee shall have access to metering equipment and disconnecting means of the Rooftop Solar Photovoltaic System, both automatic and manual, at all times.

  • Notice and Disclaimer 2.1. The Data is the property of Xxx Xxxxxxxx and is protected by applicable copyright law. In no event shall User publish, retransmit, display, redistribute, or otherwise reproduce any or all of the Data in any format to anyone, except as allowed in Section 1 of this agreement.

  • Permitted Uses and Disclosures of PHI 2.1 Unless otherwise limited herein, Business Associate may:

  • Permitted Use and Disclosure Each party hereto is permitted to disclose this AGREEMENT and use or disclose the CONFIDENTIAL INFORMATION disclosed to it by the other party:

  • Justice and Dignity The Parties agree that in certain situations, it may be in the best interest of both Employer and employees that employees be reassigned or removed from all job sites during an investigation of conduct. In cases where an employee cannot be reassigned, the employee shall be considered to be on a leave of absence without loss of pay until the Employer makes a decision relative to imposing discipline.

  • Suspension and Dismissal In the event an Employee alleges dismissal or suspension without just cause, the Employee may commence a grievance at Step II. The grievance shall be filed within ten (10) days of the occurrence.

  • MEET AND DISCUSS A. Upon request of either party, the Chancellor and/or designees of the Chancellor shall during the term of this Agreement meet with a committee appointed by the Association for the purpose of discussing matters necessary to the implementation of this Agreement.

  • RESPECT AND DIGNITY The Employer and Union agree that each employee and supervisory representative of the Employer shall be treated with dignity and respect. Verbal abuse, threats, or harassment, including sexual harassment, by employees, managers or supervisors towards each other will not be tolerated. Discipline shall be handled in a professional manner.

Time is Money Join Law Insider Premium to draft better contracts faster.