Common use of Front Clause in Contracts

Front. The right front shall have a center facing 1-1/2" wide extending from the collar stand to bottom of shirt and be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and 3-1/2" apart. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting of the flaps shall be done with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the top ply only. The left flap to have an invisible pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: Badge Tab: To be reinforced on outside of the shirt. To be 2-1/4” and have two metal eyelets 1-1/4" apart with the bottom of the patch 3/4" above left flap.

Front. The right front shall have a center facing 3" in width extending from neckline to the bottom of shirt provided by a turn under of material. The left front shall also have a lined box pleat 1-1/2" wide extending from finished, running full length of the collar stand to bottom of shirt and shall be made of the same material as shirt fabric with two rows of stitching 7/8topstitched 1/4" apartfrom both edges. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and edge. First at neck, second2-1/2" down, balance 3-1/2" apart. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satinpoplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/21/4" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting Flaps to be secured to front of the flaps shall be done shirt with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the stitching approximately 1/4" above top ply onlyof pocket. The left flap to have an invisible a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on outside inside of the shirtshirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To be 2-1/4” and have two metal eyelets small (horizontal) buttonholes, 1-1/4" apart with the bottom of the patch 3/4buttonhole 1-1/2" above top of left flap.

Front. The right front shall have a center facing 1-1/2" wide extending from the collar stand to bottom of shirt and be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and 3-1/2" apart. Zipper: A 14The button stand, 7/8" nylon zipper wide, shall be sewn self-lined and placed on left side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the fronts button stand and shall be positioned 1- 1/2" below correspond to the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn buttonholes on the top center. The neck button, 1st front button are to be functionalcenter facing. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satinpoplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/21/4" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. The top stitching and the setting Flaps to be secured to front of the flaps shall be done shirt with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the stitching approximately 1/4" above top ply onlyof pocket. The left flap to have an invisible a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on outside inside of the shirtshirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To be 2-1/4” and have two metal eyelets small (horizontal) buttonholes, 1-1/4" apart with the bottom of the patch 3/4buttonhole 1-1/2" above top of left flap.

Front. The right front shall have a center facing 1-1/2" wide extending from the collar stand to bottom of shirt and be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six (6) vertical Xxxxx buttonholes placed 3/4" from edge and 3-1/2" apart. Zipper: A 14The button stand, 7/8" nylon zipper wide, shall be sewn self-lined and placed on right side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the fronts button stand and shall be positioned 1- 1/2" below correspond to the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn buttonholes on the top center. The neck button, 1st front button are to be functionalcenter facing. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satinpoplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/211/4" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting Flaps to be secured to front of the flaps shall be done shirt with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the stitching approximately 1/4" above top ply onlyof pocket. The left flap to have an invisible a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on outside inside of the shirtshirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To be 2-1/4” and have two metal eyelets small (horizontal) buttonholes, 1-1/4" apart with the bottom of the patch 3/4buttonhole 1-1/2" above top of left flap.

Front. Each front shall have a facing 3½" in width extending from the neckline to bottom of shirt provided by a turn under of material. The right front shall have a center facing lined box pleat 1-1/2" wide extending from finished, running full length of the collar stand to bottom of shirt and shall be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4topstitched 1/4" from edge and 3-1/2" apartboth edges. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting of the flaps shall be done with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the top ply only. The left flap to have an invisible pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: Badge Tab: To be reinforced on outside of the shirt. To be 2-1/4” and have two metal eyelets 1-1/4" apart with the bottom of the patch 3/4" above left flap.

Front. The right front fronts shall have a center facing 3" in width extending from neckline to bottom of shirt provided by a turn-under of material. The right front shall also have a lined box pleat 1-1/2" wide extending from finished, running full length of the collar stand to bottom of shirt and shall be made of the same material as shirt fabric with two rows of stitching 7/8topstitched 1/4" apartfrom both edges. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and edge, first at neck, second 21/2" down, balance 3-1/2" apart. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satinpoplin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/21/4" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. The top stitching and the setting Flaps to be secured to front of the flaps shall be done shirt with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the stitching approximately 1/4" above top ply onlyof pocket. The left flap to have an invisible a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on outside inside of the shirtshirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To be 2-1/4” and have two metal eyelets small (horizontal) buttonholes, 1-1/4" apart with the bottom of the patch 3/4buttonhole 1-1/2" above top of left flap.

Front. The right front shall have a center facing 1-1/2" wide extending from the collar stand to bottom of shirt and be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and 3-1/2" apart. Zipper: A 14The button stand, 7/8" nylon zipper wide, shall be sewn self-lined and placed on left side extending from collar stand to bottom of shirt. Buttons shall be securely attached to the fronts button stand and shall be positioned 1- 1/2" below correspond to the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn buttonholes on the top center. The neck button, 1st front button are to be functionalcenter facing. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satinpoplin. Pockets: To have two breast pockets with mitered mitred corners to finish 5-5/8" wide and 65-1/2" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/21/4" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/41/4" in length, 2-3/43/8" in width at center, and 2-1/21/8" in width at sides. The top stitching and the setting Flaps to be secured to front of the flaps shall be done shirt with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the stitching approximately 1/4" above top ply onlyof pocket. The left flap to have an invisible a pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: The side points of the flaps are to be secured to the pockets by means of velcro fasteners sewn onto the flaps and pockets. Badge Tab: To be reinforced on outside inside of the shirtshirt by means of a strip of material 1-1/2" wide stitched and folded so that no raw edges show. The reinforcement strip is to extend from the flap setting stitch to the joining seam at the front of the yoke. To be 2-1/4” and have two metal eyelets small (horizontal) buttonholes, 1-1/4" apart with the bottom of the patch 3/4buttonhole 1-1/2" above top of left flap.

Front. The right left front shall have a center facing 1-1/2" wide extending from the collar stand to bottom of shirt and be made of the same material as shirt fabric with two rows of stitching 7/8" apart. The center front shall contain six vertical Xxxxx buttonholes placed 3/4" from edge and 3-1/2" apart. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting of the flaps shall be done with two rows of stitching. Flaps to have vertical stitched-in creases through the center on the top ply only. The left flap to have an invisible pencil opening about 1-1/4" in width. Flaps to be interlined. There will be a non-functional matching button and a buttonhole sewn on the flap. Flaps will be made to accommodate removable metal buttons. Flap Closure: Badge Tab: To be reinforced on outside of the shirt. To be 2-1/4” and have two metal eyelets 1-1/4" apart with the bottom of the patch 3/4" above left flap.