Common use of Front Clause in Contracts

Front. Each front shall have a facing approximately 3” in width. The left front shall have a top center placket 1-1/2" wide with two rows of stitches 7/8" apart. Stitching on the top center is not to be visible on the turn back facing. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3-¾" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw Shoulder straps to be two-piece pointed, 1/4" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have non-functional buttonhole with a well sewn button centered on buttonhole. Points of shoulder straps to be tacked to the shoulder. Edge stitched shoulder strap constructionunacceptable. Two-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1-1/4” from top of pocket flap spaced 1-1/4” apart and centered on sling.

Front. Each front shall have a facing approximately 3” in width. The left front shall have a top center placket 1-1- 1/2" wide with two rows of stitches 7/8" apart. Stitching on the top center is not to be visible on the turn back facing. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3-¾3- ¾" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16" raised stitch. Safety stitch joining unacceptable. A 15” nylon zipper, to be set below the second button and buttonhole, shall accomplish front closure. The top, second and bottom buttons to be attached to the right front, the balance to be sewn over the buttonholes on the left front. Shoulder straps to be two-piece pointed, 1/4" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have non-functional buttonhole with a well sewn button centered on buttonhole. Points of shoulder straps to be tacked to the shoulder. Edge stitched shoulder strap constructionunacceptable. Two-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1-1/4” from top of pocket flap spaced 1-1/4” apart and centered on slingconstruction unacceptable.

Front. Each front shall have a facing approximately 3” " in width. The left right front shall have a top center placket xxxxxx/ t 1-1/21/ 2" wide with two rows of stitches 7/87/ 8" apart. Stitching on the top center is not to be visible on the turn back facing. The shirt will have 7 6 buttons and buttonholes on interlining the front; spacing between each will be 3-¾3 1 2" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/41 / 4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining is unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between , and then all three are stitched down with a 1/ 16" raised stitch. Safety stitch joining unacceptable. An 11 ½" nylon zipper, to be set below the second button and buttonhole, shall accomplish front closure. The top, second and bottom buttons to be attached to the left front, the balance to be sewn over the buttonholes on the right front. Shoulder straps to be two-piece pointed, 1/4" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have non-functional buttonhole with a well sewn button centered on buttonhole. Points of shoulder straps to be tacked to the shoulder. Edge stitched shoulder strap constructionunacceptable. Two-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1-1/4” from top of pocket flap spaced 1-1/4” apart and centered on sling.

Front. Each front shall have a facing approximately 3” " in width. The left right front shall have a top center placket 1-1/21/ 2" wide with two rows of stitches 7/87/ 8" apart. Stitching on the top center is not to be visible on Woven the turn back facing. The shirt will have 7 6 buttons and buttonholes on interlining the front; spacing between bet/ ween each will be 3-¾3 1 2" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/41 / 4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between , and then all three are stitched down with a 1/ 16" raised stitch. Safety stitch joining unacceptable. An 11 ½" nylon zipper, to be set below the second button and buttonhole, shall accomplish front closure. The top, second and bottom buttons to be attached to the left front, the balance to be sewn over the buttonholes on the right front. Shoulder straps to be two-piece pointed, 1/4" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have non-functional buttonhole with a well sewn button centered on buttonhole. Points of shoulder straps to be tacked to the shoulder. Edge stitched shoulder strap constructionunacceptable. Two-ply sling 1” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1-1/4” from top of pocket flap spaced 1-1/4” apart and centered on sling.

Front. Each front shall have a facing approximately 3” 3½" in widthwidth extending from the neckline to bottom of shirt provided by a turn under of material. The left front shall have a top center placket lined box pleat 1-1/2" wide finished, running full length of the shirt and shall be topstitched 1/4" from both edges. Zipper: A 14" nylon zipper shall be sewn to the fronts and shall be positioned 1- 1/2" below the first front button and shall replace the 2nd, 3rd, 4th, and 5th front buttons, which are to be sewn on the top center. The neck button, 1st front button are to be functional. Back: There is to be a yoke composed of an outer piece of the same material as the basic shirt, and an inner piece of matching satin. Pockets: To have two breast pockets with mitered corners to finish 5-5/8" wide and 6" long. The left breast pocket to have a pencil compartment about 1-1/4" wide. Both pockets to have 1-1/2" box stitching top and bottom to prevent spreading. There will be vertical stitched-in creases running through the center of each pocket. There shall be a small buttonhole in the pocket for the insertion of a removable metal button. Flaps: To have two scalloped flaps to finish 5-3/4" in length, 2-3/4" in width at center, and 2-1/2" in width at sides. The top stitching and the setting of the flaps shall be done with two rows of stitches 7/8" apartstitching. Stitching Flaps to have vertical stitched-in creases through the center on the top center is not ply only. The left flap to have an invisible pencil opening about 1-1/4" in width. Flaps to be visible on the turn back facinginterlined. The shirt will have 7 buttons and buttonholes on the front; spacing between each There will be 3-¾" except the spacing between the neck button and the first button on the front, which will be approximately 3-1/4". Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw Shoulder straps to be two-piece pointed, 1/4" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1-3/8" and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have a non-functional matching button and a buttonhole with a well sewn button centered on buttonholethe flap. Points Flaps will be made to accommodate removable metal buttons. Flap Closure: Badge Tab: To be reinforced on outside of shoulder straps to the shirt. To be tacked to the shoulder. Edge stitched shoulder strap constructionunacceptable. Two2-ply sling 11/4” wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole two metal eyelets 1-1/4” from top " apart with the bottom of pocket flap spaced 1-1/4” apart and centered on slingthe patch 3/4" above left flap.