GLAZING TO STEEL WITH PUTTY. 4mm Clear float glass 60 Panes not exceeding 0,1 m2 m2 47 4mm Rough cast glass 61 Panes not exceeding 0,1m2 PAINTWORK m2 14 PREPARATORY WORK TO EXISTING WORK Previously painted wood surfaces Surfaces shall be thoroughly cleaned down. Blistered or peeling paint shall be completely removed and cracks and crevices shall be primed, filled with suitable filler and finished smooth Previously painted metal surfaces Surfaces shall be thoroughly rubbed and cleaned down. Blistered or peeling paint shall be completely removed down to bare metal Previously painted plastered surfaces Surfaces shall be thoroughly washed down and allowed to dry completely before any paint is applied. Blistered or peeling paint shall be completely removed and cracks shall be opened, filled with a suitable filler and finished smooth PAINTWORK ETC TO NEW WORK FLOATED PLASTER SURFACES WITH Carried to Collection R Prepare and apply one coat plaster primer, one filler coat and two coats Velvaglo paint on 62 External walls m2 357 Prepare and apply one coat plaster primer, one filler coat and two coats Velvaglo paint on 63 Internal walls m2 583 ON WOOD Sand down and apply to coats of "WOODOC 30" varnish 64 On doors m2 20 ON METAL Spot priming defects in pre-primed surfaces, apply one coat "Dulux Duraphos Primer" one coat Dulux Undercoat" and two coats "Dulux Dura 100 Gloss Enamel Paint DWI006" or similar approved on previously painted steel in good condition 65 On windows with burglar bars m2 64 PAINTWORK ETC TO PREVIOUSLY PAINTED WORK ON METAL Spot priming defects in pre-primed surfaces, apply one coat "Dulux Duraphos Primer" one coat Dulux Undercoat" and two coats "Dulux Dura 100 Gloss Enamel Paint DWI006" or similar approved on previously painted steel in good condition 66 On door frames m2 21 APRONS AROUND BUILDINGS Compaction of surfaces 67 Compaction of ground surface under aprons including scarifying for a depth of 150mm, breaking down oversize material, adding suitable material where necessary and compacting to 90% Mod AASHTO density m2 119 Carried to Collection R 15 MPa/20 mm concrete 68 Aprons cast in panels to falls m3 12 Finishing top surfaces of concrete smooth with a wood float 69 Aprons to falls m2 119 Smooth formwork to sides 70 Edges, risers, ends and reveals not exceeding 300mm high or wide m 119 Carried to Collection R R Amount Section No. 5 RENOVATIONS OF SPECIAL LEARNING BLOCK Bill No. 1 RENOVATIONS OF SPECIAL LEARNING BLOCK COLLECTION Page No Total Brought Forward from Page...
GLAZING TO STEEL WITH PUTTY. 4mm Clear float glass: 1 Panes exceeding 0,1m² and not exceeding 0,5m². m2 52
GLAZING TO STEEL WITH PUTTY. 4mm Clear float glass: 1 Panes exceeding 0,1m² and not exceeding 0,5m². m2 181 6mm Obscure float glass: 2 Panes exceeding 0,1m2 and not exceeding 0,5m2. m2 147 Carried Forward to Summary of Section No. 3 R Section No. 3 ALTERATIONS - 3 X 6 CLASSROOM Bill No. 12 Glazing Zethu Consulting Services Amount
GLAZING TO STEEL WITH PUTTY. 6mm Laminated Obscure safety glass 1 Panes exceeding 0,5m2 and not exceeding 2m2 m2 176 Carried to Collection R Bill No. 12 Glazing Prepared by Takgalang Consulting Amount
GLAZING TO STEEL WITH PUTTY. 4mm Clear float glass 1 Panes exceeding 0,5m2 and not exceeding 2m2 m2 27 Carried Forward to Summary of Section No. 2 R Amount Item No SECTION NO.2 BUILDING WORK BILL NO.13 PAINTWORK For preambles see "Model Preambles for Trades (2008 Edition)" and Supplementary preambles as specified in the Trades. Quantity Rate PAINTWORK ETC TO NEW WORK ON FLOATED PLASTER Plascon Polvin Super Acrylic to interior new cement plaster (NW 205).Surface to be dry, sound and clean and cured for a minimum of 14 days, with a moisture content measured with a Doser Hygrometer (or equivalent), of BD 2 scale - 8% or less. Prime with one coat of Plascon Plaster Primer (UC 56) with an overcoating time of 16 hours and finish with two coats of Polvin Super Acrylic (EPL) with 1 hour drying time between coats, for a maintenance cycle of 5 years in a C1 - inland environment. 1 On internal walls m2 693 ON SMOOTH CONCRETE Prepare surfaces and remove all loose material, and rinse. Apply flexible crackfiller to holes and cracks, one coat plaster primer and two coats Plascon Professional Copolymer Acrylic paint ON FIBRE-CEMENT Carried Forward R Amount Brought Forward R One coat primer, one coat universal undercoat and two coats super acrylic PVA paint 2 On ceilings and cornices m2 590 Plascon Sure Coat Gloss Enamel to exterior new fibre cement (NW 174).Surface to be dry, sound and clean, with a moisture content, measured with a Doser Hygrometer (or equivalent), of BD 2 scale - 8% or less. Prime with one coat of Plascon Plaster Primer (UC 56) with an overcoating time of 16 hours and finish with two coats of Sure Coat Gloss Enamel (SGE) with 16 hours drying time between coats, for a maintenance cycle of 2 years in a C1 - inland environment. 3 On fascias and barge boards m2 54 Plascon Sure Coat Gloss Enamel to interior new fibre cement (NW 274).Surface to be dry, sound and clean, with a moisture content, measured with a Doser Hygrometer (or equivalent), of BD 2 scale - 8% or less. Prime with one coat of Plascon Plaster Primer (UC 56) with an overcoating time of 16 hours and finish with two coats of Sure Coat Gloss Enamel (SGE) with 16 hours drying time between coats, for a maintenance cycle of 4 years in a C1 - inland environment. ON METAL Carried Forward R Brought Forward R Plascon Velvaglo Satin to exterior new mild steel (NW 683).Surface to be clean and dry. Remove surface contaminants using Plascon Aquasolv Degreaser (GR 1) with bristle brush or Brillo pads. Rinse thoroughly with tap water unti...
GLAZING TO STEEL WITH PUTTY. 6.38mm Normal strength (NS) clear laminated safety glass 1 Panes exceeding 0,1m2 and not exceeding 0,5m2 m2 144 6.38mm Normal strength (NS) obscure tinted laminated safety glass Carried Forward to Summary of Section No. 2 R Section No. 2 4 X 4-CLASSROOMS WITH STORES Bill No. 13 GLAZING Xxxx Xxxxxxx Primary School
GLAZING TO STEEL WITH PUTTY. 5mm Clear Float glass 35 5mm Clear Float glass fixed with glazing putty exceeding 0.1m² and not exceeding 0.5m² square metre in area m2 26
GLAZING TO STEEL WITH PUTTY. 6,38mm Normal strength obscure laminated safety glass: 58 Panes exceeding 0,1m² and not exceeding 0,5m². m2 3 PAINTWORK
GLAZING TO STEEL WITH PUTTY. 4mm Obscure safety glass 1 Panes not exceeding 0,1 m2 m2 2 Carried Forward to Summary of Section No. 3 R 3 SEATS GRADE R TOILETS GLAZING Amount Item Quantity Rate Amount
GLAZING TO STEEL WITH PUTTY. 4mm Obscure safety glass 1 Panes not exceeding 0,1 m2 m2 2 Carried Forward to Summary of Section No. 4 R 3 SEATS GIRLS TOILETS GLAZING Amount Item Quantity Rate Amount
