Common use of Horizontal adjustment Clause in Contracts

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: a) The "0.2 D line" method (see figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: a) The "0.2 D line" method (see figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: (a) The "0.2 D line" method (see figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – - log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: (a) The "0.2 D line" method (see figure Figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: (a) The "0.2 D line" method (see figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: (a) The "0.2 D line" method (see figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H2

Horizontal adjustment. The applicant shall specify one of the following horizontal aim methods: (a) The "0.2 D line" method (see figure Figure 2 below). A single horizontal line at 0.2° D shall be scanned from 5° left to 5° right after the lamp has been aimed vertically. The maximum gradient "G" determined using the formula G = (log Eβ – log E(β + 0.1°)) where β is the horizontal position in degrees, shall not be less than 0.08. The inflection point found on the 0.2 D line shall be positioned on the line A. Figure 2 V H H2