Manufacturing Standards All forest products except poles, produced and sold under this contract will be manufactured to maximize the amount of logs meeting preferred log lengths and to achieve the average log length listed. 97318 3 WS "WS" indicates that west side scaling rules apply. Minimum trim is 8 inches per scaling segment for west side scaling rules. "ES" indicates that east side scaling rules apply. Minimum trim is 4 inches per scaling segment for east side scaling rules. Poles produced under this contract will be manufactured to ANSI specifications (American National Standard Specifications and Dimensions for Wood Poles), in force at the time of signing this contract. a. Sweep will be limited to within the bole of the log as measured using a tape stretched between the centers of each end of the log. b. Logs approved by the state for peelers shall be chuckable with no more than a 2 inch diameter area of rot within a 5 inch diameter circle located at the center of either end of the log. c. Limbs and knots shall be cut flush, with no more than 15 percent of a log having limbs or knots over 2 inches in diameter extending more than 2 inches above the surface of the log.
Service Level Standards In addition to all other requirements in this Agreement, and in accordance with the Best Claims Practices & Estimating Guidelines, Vendor shall use reasonable and good faith efforts to meet the Service Level Standards set forth below.
Operating Standards (A) Distributor and its Dealer(s) shall conduct the operation of their respective businesses related to the resale of the Product(s) in a clean and safe manner and shall otherwise conduct no business which could interfere with the sale of Product(s) or damage the goodwill of the Valero brand or the Marks. Without limiting the foregoing, Distributor and its Dealer(s) shall, at all times during the term of this Agreement, fully comply with VMSC’s then current “Basic Operational Requirements” which Distributor acknowledges have been received and reviewed by Distributor. Furthermore, without limiting any provision to the contrary herein, Distributor and its Dealer(s) shall fully comply with VMSC’s “Commitment to Excellence Requirements”, which Distributor acknowledges have been received and reviewed by Distributor. As of the Commencement Date, Distributor and its Dealer(s) agree to participate in the Commitment to Excellence Program (“CTE Program”). The CTE Program provides that each Station meets the established Commitment to Excellence Requirements which consists of requirements from each of the following VMSC documents: VMSC’s Basic Image Requirements, Wholesale Branding Manual, and Basic Operational Requirements. VMSC reserves the right to amend, change, or otherwise modify the “Basic Operational Requirements”, “Commitment to Excellence Requirements” and the “CTE Program” from time to time, in VMSC’s sole and absolute discretion. (B) Distributor and its Dealer(s) shall comply with all Laws of any governing authority or agency having jurisdiction or purporting to have jurisdiction relating to the handling, storage, testing, sale, distribution, transportation, and/or use of the Product(s) and shall further comply with all rules, guidelines, and procedures of VMSC in connection with the loading, transportation, handling, storing, testing, selling, dispensing, and/or use of the Product(s). (C) Subject to Paragraph 12 of this Agreement, Distributor and its Dealer(s) shall continuously offer at least three grades of “Valero” branded gasoline at each Station. (D) Distributor and its Dealer(s) will utilize and maintain updated point of sale systems as required by VMSC. VMSC also reserves the right to install, and Distributor and its Dealer(s) agree to utilize, update and maintain, other automated systems, at Distributor’s cost, as required by VMSC, including but not limited, such systems necessary to poll, at frequencies determined by VMSC, each Station’s Product sales. (E) VMSC may inspect or review compliance by Distributor and its Dealer(s) with the requirements of this Paragraph 8 in any reasonable manner that VMSC determines, including, but not limited to, announced and unannounced visits. (F) Distributor expressly understands and agrees that a confidential relationship is established between VMSC and Distributor under this Agreement and that, as a result thereof, VMSC will be disclosing and transmitting to Distributor certain confidential and proprietary information in connection with the Distributor’s operation of the Station. Distributor hereby agrees that Distributor shall not, during the term of this Agreement or thereafter, communicate, divulge or use for the benefit of any other person, persons, partnership, association or corporation and, following the expiration or termination of this Agreement, shall not use for the benefit of Distributor, or any of its principals, any confidential information, knowledge or know-how concerning the methods of operation (including pricing) of the Station which may be communicated to Distributor or its principals or of which they may be apprised in connection with the operation of the Station(s) under the terms of this Agreement. Distributor shall divulge such confidential information only to such of Distributor’s employees as must have access to it in order to operate the Station(s). Any and all information, knowledge, know-how, techniques and any materials used in or related to the Station which VMSC provides to Distributor in connection with this Agreement shall be deemed confidential for purposes of this Agreement. Such confidential information does not include information that, at the time it was disclosed to or learned by Distributor, was part of the public domain, nor information that, after the time it was disclosed to or learned by Distributor, became part of the public domain through disclosure, publication or communication by persons other than Distributor or its employees. Distributor shall not at any time, without VMSC’s prior written consent, copy, duplicate, record or otherwise reproduce such materials or information, in whole or in part, nor otherwise make the same available to any unauthorized person. (G) Distributor acknowledges that strict compliance with the terms and conditions of this Paragraph 8 is a material and important part of the consideration for this Agreement.
OMB Standards Unless specified otherwise within this agreement, the Subrecipient shall procure all materials, property, or services in accordance with the requirements of 24 CFR 84.40−48.
Construction Standards The Developer shall construct the Subdivision in accordance with the Subdivision Plan, as approved by the Planning Commission, and if applicable, the requirements of the Design Review Committee, and in accordance with the requirements of (a) the Millington Subdivision Regulations; (b) standards and specifications contained in “Local Public Works Standard, and Specifications”, as amended to include specific requirements for construction in Millington, TN; (c) the Building Code (as adopted by Shelby County); (d) the Fire Code (as adopted by Shelby County); (e) the Millington Zoning Ordinance; and (f) the applicable Ordinances of the City. Items (a) through (f) are hereby made a part of this Agreement by reference and are hereinafter referred to collectively as the “Codes”. References herein to the Codes are to those in effect on the Effective Date unless amendments are hereafter made which apply to all improvements or subdivisions regardless of their date of commencement and/or completion of construction. The Conditions of Approval established by the Planning Commission, and, as applicable, the Design Review Committee (any or all of which as may have been modified by the Board of Mayor and Aldermen) are set forth in Exhibit “A” to this Agreement and are incorporated herein by reference and made a part hereof.
Work Standards The Contractor shall execute its responsibilities by following and applying at all times the highest professional and technical guidelines and standards. If the State becomes dissatisfied with the work product of or the working relationship with those individuals assigned to work on this Contract, the State may request in writing the replacement of any or all such individuals, and the Contractor shall grant such request.
Design Criteria and Standards All Projects/Services shall be performed in accordance with instructions, criteria and standards set forth by the Director.
Licensing Standards The Contractor, its employees and subcontractors shall comply with all applicable licensing standards, certification standards, accrediting standards and any other laws, rules, or regulations governing services to be provided by the Contractor pursuant to this Contract. The State will not pay the Contractor for any services performed when the Contractor, its employees or subcontractors are not in compliance with such applicable standards, laws, rules, or regulations. If any license, certification or accreditation expires or is revoked, or any disciplinary action is taken against an applicable license, certification, or accreditation, the Contractor shall notify the State immediately and the State, at its option, may immediately terminate this Contract.
System for Award Management (XXX) Requirement Alongside a signed copy of this Agreement, Grantee will provide Florida Housing with a XXX.xxx proof of registration and Commercial and Government Entity (CAGE) number. Grantee will continue to maintain an active XXX registration with current information at all times during which it has an active award under this Agreement.
Quality Standards Each Party agrees that the nature and quality of its products and services supplied in connection with the other Party's Marks will conform to quality standards set by the other Party. Each Party agrees to supply the other Party, upon request, with a reasonable number of samples of any Materials publicly disseminated by such Party which utilize the other Party's Marks. Each Party will comply with all applicable laws, regulations, and customs and obtain any required government approvals pertaining to use of the other Party's marks.
