Industrial Loads Sample Clauses

Related to Industrial Loads

Electrical During the Term of this Lease, there shall be available to the Leased Premises electrical facilities comparable to those supplied in other comparable office buildings in the vicinity of the Building to provide sufficient power for normal lighting and office machines of similar low electrical consumption, and one personal computer for each desk station, but not for any additional computers or extraordinary data processing equipment, special lighting and any other item of electrical equipment which requires a voltage other than one hundred ten (110) volts single phase and is not typically found in an office, as determined by Landlord in its sole, but reasonable discretion; and provided, however, that if the installation of such electrical equipment requires additional air conditioning capacity above that normally provided to tenants of the Building or above standard usage of existing capacity as determined by Landlord in its sole, but reasonable discretion, then the additional air conditioning installation and/or operating costs attributable thereto shall be paid by Tenant. Tenant agrees not to use any apparatus or device in, upon or about the Leased Premises which may in any way increase the amount of such electricity usually furnished or supplied to the Leased Premises, and Tenant further agrees not to connect any apparatus or device to the wires, conduits or pipes or other means by which such electricity is supplied, for the purpose of using additional or unusual amounts of electricity, without the prior written consent of Landlord. At all times, Tenant’s use of electric current shall never exceed Tenant’s share of the capacity of the feeders to the Building or the risers or wiring installation. Tenant shall not install or use or permit the installation or use in the Leased Premises of any computer or electronic data processing or ancillary equipment or any other electrical apparatus designed to operate on electrical current in excess of 110 volts and 5 amps per machine, without the prior written consent of Landlord, which consent shall not be unreasonably withheld, conditioned or delayed. If Tenant shall require electrical current in excess of that usually furnished or supplied for use of the Leased Premises as general office space, Tenant shall first procure the written consent of Landlord (which consent shall not be unreasonably withheld, conditioned or delayed) to the use thereof and Landlord or Tenant may (i) cause a meter to be installed in or for the Leased Premises, or (ii) if Tenant elects not to install said meter, Landlord may reasonably estimate such excess electrical current. The cost of any meters (including, without limitation, the cost of any installation) or surveys to estimate such excess electrical current shall be paid by Tenant. Landlord’s approval of any space plan, floor plan, construction plans, specifications, or other drawings or materials regarding the construction of the Tenant Improvements or any alterations shall not be deemed or construed as consent by Landlord under this paragraph to Tenant’s use of such excess electrical current as provided above. Tenant agrees to pay to Landlord, promptly upon demand therefor, all costs of such excess electrical current consumed as calculated by said meters (at the rates charged for such services to the Building by the municipality or the local public utility) or the excess amount specified in said estimate, as the case may be, plus any additional expense incurred in keeping account of the electrical current so consumed, which additional expense Landlord shall advise Tenant within a reasonable time after request by Tenant.
Fuel Upon redelivery of the Aircraft to Lessor, an adjustment will be made in respect of fuel on board on the Previous Delivery Date and the Expiry Date at the price then prevailing at the Redelivery Location.
Capital Equipment Collaborator’s commitment, if any, to provide ICD with capital equipment to enable the research and development activities under the Research Plan appears in Appendix B. If Collaborator transfers to ICD the capital equipment or provides funds for ICD to purchase it, then ICD will own the equipment. If Collaborator loans capital equipment to ICD for use during the CRADA, Collaborator will be responsible for paying all costs and fees associated with the transport, installation, maintenance, repair, removal, or disposal of the equipment, and ICD will not be liable for any damage to the equipment.
Building With respect to each parcel of Real Estate, all of the buildings, structures and improvements now or hereafter located thereon. Business Day. Any day on which banking institutions located in the same city and State as the Agent’s Head Office are located are open for the transaction of banking business and, in the case of LIBOR Rate Loans, which also is a LIBOR Business Day.
Equipment The Fund shall obtain and maintain at its own cost and expense all equipment and services, including but not limited to communications services, necessary for it to utilize the Software and obtain access to the System, and Custodian shall not be responsible for the reliability or availability of any such equipment or services.
Infrastructure (a) The Borrower has and will maintain a sufficient infrastructure to conduct its business as presently conducted and as contemplated to be conducted following its execution of this Agreement.
Lighting Landlord will furnish both Building Standard and non-Building Standard lamps, bulbs, ballasts and starters that are part of the Leasehold Improvements for purchase by Tenant at Landlord's cost, plus Landlord's standard administration fee. Landlord will install non-Building Standard items at Landlord's scheduled rate for this service.
Raw Materials Lonza shall procure all required Raw Materials as well as consumables other than those Raw Materials that are Customer Materials. Customer shall be responsible for payment for all consumables and Raw Materials ordered or irrevocably committed to be procured by Lonza hereunder. Upon cancellation of any Batch or termination of the Agreement, all unused Raw Materials shall be paid for by Customer within [***] days of invoice and at Customer’s option will either be (a) held by Lonza for future use for the production of Product, (b) delivered to Customer, or (c) disposed of by Lonza.
Supplies All china, glassware and silverware, linens, uniforms, engineering, maintenance, cleaning and housekeeping supplies, matches and ashtrays, soap and other toiletries, stationery, menus, directories and other printed materials, and all other similar supplies and materials, which are located at the Hotel or ordered for future use at the Hotel as of the Closing (the “Supplies”);
Materials and Equipment Except for materials or Equipment to be supplied by Subcontractors identified on part B of Schedule 7, whenever materials or Equipment are specified or described in this Contract (including the Specifications) by using the name of a proprietary item or the name of a particular supplier, the naming of the item is intended to establish the type, function and quality required, and substitute materials or Equipment may nonetheless be used, provided that such materials or Equipment are equivalent or equal to that named. If the Vendor wishes to furnish or use a substitute item of material or Equipment, the Vendor must first certify that the proposed substitute will perform at least as well the functions and achieve the results called for by this Contract, will be substantially similar or of equal substance to that specified and be suited for the same use as that specified. The Owner may require the Vendor to furnish, at the Vendor's expense, additional data about the proposed substitute as required to evaluate the substitution. For Major Portions of the Work, or materials or Equipment listed on part B of Schedule 7, the Vendor must first receive prior written approval of the Owner for any substitution. The Owner will be allowed a reasonable time within which to evaluate each proposed substitute. Notwithstanding the foregoing, with respect to PCS Products, prior to the shipment of such PCS Products pursuant to the terms of this Contract, the Vendor may at any time without notice to or consent of the Owner make changes in a Vendor PCS Product furnished pursuant to this Contract, or modify the drawings and published specifications relating thereto, or substitute Products of similar or later design to fulfill its obligations under this Contract or otherwise fill an order, provided that the changes, modifications or substitutions will in no way affect or otherwise impact upon the form, fit, or function of an ordered Product pursuant to and in accordance with the applicable Specifications. With respect to changes, modifications and substitutions which do in fact affect the form, fit, or function of an ordered Product pursuant to and in accordance with the Specifications, the Vendor must notify the Owner in writing at least thirty (30) days prior to the effective dates of any such changes, modifications or substitutions. In the event that any such change, modification or substitution is not desired by the Owner, the Owner will notify the Vendor within thirty (30) days from the date of notice and the Vendor will not furnish any such changed Products to the Owner on any orders in process at the time the Owner is so notified; provided that nothing contained herein will otherwise modify the Vendor's obligations under the terms of this Contract.