, Ingot Marking Sample Clauses

, Ingot Marking. As Dunkerque does not yet have the possibility of marking with barcode labels, a transition period until 30.06.2012 to close this gap is accepted by ASG.
Sample 1Sample 2
AutoNDA by SimpleDocs
, Ingot Marking. INGOT HEAD: Steel Stamp Oswego Alloy Code (Optional) and Vendor Ingot Number. • INGOT SHORT SIDES: Ink stencil Oswego Alloy Code, Ingot size (thickness, width, and length), Vendor Ingot Number, and Actual Ingot Weight (lbs). The required ink stenciling for Oswego Hot Mill shall be a minimum of 2.75 inches (70mm) high. Any other “plant identification” required by the ingot supplier may be added. • Bar code labels shall be placed on both the short sides no more than 15” from either end of the ingot and on the ingot head about 2” from the rolling face and 2” from the short side. Correct placement of the bar code labels is essential for ingot receiving and in-plant handling. Exceptions only if approved in advance in writing. Bar Code Label shall include Vendor Ingot Number as both Code 128 bar code with min 1 mil bars and min 1/2” high man readable. • Ingots delivered by trucks must be covered. No exception.
Sample 1
, Ingot Marking. INGOT SHORT SIDES: Ink stencil Novelis Alloy Code, Ingot size (thickness, width, and length), Vendor Ingot Number, and Actual Ingot Weight (kg). The required ink stenciling shall be a minimum of 2.75 inches (70mm) high. Any other “plant identification” required by the ingot supplier may be added. • Ingots delivered by trucks must be covered. No exception.
Sample 1
, Ingot Marking. The normal ingot marking (ingot identification number) which has a length of approximately 3000 mm is located on both narrow sides with a height of 90 mm +/- 20 mm ( using stencil or with an automatic marking system). The ingot is to be marked at mid-thickness. The ink used must be weather and heat resistant, so that it is readable after homogenization. For example Manufacturer Sander, Material description: Xxxxx colour blue, double pigmentation, Sander no. 20908. *** 10.5.1.1. Casting plant Up to 3 digit number, which identifies the casting plant where the corresponding ingot is cast. This number is assigned by AluNorf. 10.5.1.2. Cast number Up to 6 digit number, which identifies the cast.
Sample 1
, Ingot Marking. INGOT HEAD: Steel Stamp Ulsan Alloy Code (Optional) and Vendor Ingot Number. • INGOT SHORT SIDES: Ink stencil Ulsan Alloy Code, Ingot size (thickness, width, and length), Vendor Ingot Number, and Actual Ingot Weight (kg). The required ink stenciling for Ulsan shall be a minimum of 2 inches (50mm) high. Any other “plant identification” required by the ingot supplier may be added. • Ingots delivered by trucks must be covered. No exception. • Stenciling is required on both short faces.
Sample 1
, Ingot Marking. INGOT HEAD: Steel Stamp Yeongju Alloy Code (Optional) and Vendor Ingot Number. • INGOT SHORT SIDES: Ink stencil Yeongju Alloy Code, Ingot size (thickness, width, and length), Vendor Ingot Number, and Actual Ingot Weight (kg). The required ink stenciling for Yeongju shall be a minimum of 2 inches (50mm) high. Any other “plant identification” required by the ingot supplier may be added. • Ingots delivered by trucks must be covered. No exception.
Sample 1

Related to , Ingot Marking

  • Patent Marking LICENSEE shall xxxx all Licensed Products made, used or sold under the terms of this Agreement, or their containers, in accordance with the applicable patent marking laws.

  • License for Txdot Logo Use DocuSign Envelope ID: 08011FCF-93C2-4F54-8A05-20A33047A1D8

  • Markings If permitted by applicable Law, on or reasonably promptly after the Closing Date, Owner will cause to be affixed to, and maintained in, the cockpit of the Airframe and on each Engine, in each case, in a clearly visible location, a placard of a reasonable size and shape bearing the legend: “Subject to a security interest in favor of Wilmington Trust, National Association, not in its individual capacity but solely as Mortgagee.” Such placards may be removed temporarily, if necessary, in the course of maintenance of the Airframe or Engines. If any such placard is damaged or becomes illegible, Owner shall promptly replace it with a placard complying with the requirements of this Section.

  • Marking Shipments, shipping containers and palletized unit loads shall be marked in accordance with MIL- STD-129R with Change 1 dated 24 May 2018.

  • Sublicense to Use the Scudder Trademarks As exclusive licensee of the rights to use anx xxxxxcense the use of the "Scudder," "Scudder Investments" and "Scudder, Stevens & Clark, Inx." xxxdemaxxx (xxgether, the "Scuddex Xxxxx"), xxx xerexx xxant the Trust a nonexclusive right xxx xxxlicense to use (i) the "Scudder" name and mark as part of the Trust's name (the "Fund Namx"), xxd (ii) the Scudder Marks in connection with the Trust's investment products xxx xxxvices, in each case only for so long as this Agreement, any other investment management agreement between you or any organization which shall have succeeded to your business as investment manager ("your Successor") and the Trust, or any extension, renewal or amendment hereof or thereof remains in effect, and only for so long as you are a licensee of the Scudder Marks, provided however, that you agree to use your best xxxxxxx to maintain your license to use and sublicense the Scudder Marks. The Trust agrees that it shall have no right to suxxxxxxxe or assign rights to use the Scudder Marks, shall acquire no interest in the Scudder Marks othxx xxxx the rights granted herein, that all of txx Xxxxt's uses of the Scudder Marks shall inure to the benefit of Scudder Trust Company xx xxxer and licensor of the Scudder Marks (xxx "Xrademark Owner"), and that the Trust shall nxx xxxxlenge the validity of the Scudder Marks or the Trademark Owner's ownership thereof. The Truxx xxxxher agrees that all services and products it offers in connection with the Scudder Marks shall meet commercially reasonable standards of duaxxxx, xs may be determined by you or the Trademark Owner from time to time, provided that you acknowledge that the services and products the Trust rendered during the one-year period preceding the date of this Agreement are acceptable. At your reasonable request, the Trust shall cooperate with you and the Trademark Owner and shall execute and deliver any and all documents necessary to maintain and protect (including but not limited to in connection with any trademark infringement action) the Scudder Marks and/or enter the Trust as a registered user thereof. Xx xxch time as this Agreement or any other investment management agreement shall no longer be in effect between you (or your Successor) and the Trust, or you no longer are a licensee of the Scudder Marks, the Trust shall (to the extent that, and as soon ax, xx xawfully can) cease to use the Fund Name or any other name indicating that it is advised by, managed by or otherwise connected with you (or your Successor) or the Trademark Owner. In no event shall the Trust use the Scudder Marks or any other name or mark confusingly similar therexx (xxxluding, but not limited to, any name or mark that includes the name "Scudder") if this Agreement or any other investment advisory agrexxxxx xetween you (or your Successor) and the Fund is terminated.

  • Labelling The distributor, on behalf of the selected vendor agrees that all supplies of articles should invariably contain the following information on its label and the carton. One information should not be overlapped by any other information needed to be furnished. The label should contain : a. Name of the item as approved b. CMS Cat. No. c. Manufacturing date/Import date for the imported items. d. Expiry Date. (where applicable) e. Name & address of Registered Office of Manufacturers and place of manufacture. f. Manufacturing License Number. (where applicable for Manufactures) g. Batch Number (where applicable) h. Month and Year of supply. i. The label & Carton must invariably marked “W B. GOVT SUPPLY : NOT FOR SALE”. j. All Surgical items quoted/supplied by the tenderer must conform to IS /BIS /CE/USFDA. Pacemker must conform to CE & US FDA norms. In case of Drugs items quoted /supplied by tenderer MUST CONFORM TO IP, BP, or USP norms and N.F.I. –III specification as noted against the item(s) in catalogue as applicable. k. The MRP and Trade Name will not be allowed to be printed in any pack. This will lead to cancellation of candidature straightaway. However, for excisable products, insertion of writing of Govt MRP is allowed as per provision laid down in the order of the Central Excise dept. However, for imported item(s), MRP and Trade name may be allowed in addition to Generic name.

  • Domain Name Data 1.5.1 Query format: whois EXAMPLE.TLD 1.5.2 Response format:

  • Marking of Licensed Products To the extent commercially feasible and consistent with prevailing business practices, Company shall xxxx, and shall cause its Affiliates and Sublicensees to xxxx, all Licensed Products that are manufactured or sold under this Agreement with the number of each issued patent under the Patent Rights that applies to such Licensed Product.

  • Domain Name Data (1) Query format: whois EXAMPLE.TLD (2) Response format:

  • Metadata Where the Contractor has or generates metadata as a result of services provided to the Province, where that metadata is personal information, the Contractor will: not use it or disclose it to any other party except where the Agreement otherwise specifies; and remove or destroy individual identifiers, if practicable.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!