Markings Sample Clauses
Markings. If permitted by applicable Law, on or reasonably promptly after the Closing Date, Owner will cause to be affixed to, and maintained in, the cockpit of the Airframe and on each Engine, in each case, in a clearly visible location, a placard of a reasonable size and shape bearing the legend: “Subject to a security interest in favor of Wilmington Trust, National Association, not in its individual capacity but solely as Mortgagee.” Such placards may be removed temporarily, if necessary, in the course of maintenance of the Airframe or Engines. If any such placard is damaged or becomes illegible, Owner shall promptly replace it with a placard complying with the requirements of this Section.
Markings. Every hose shall bear, at intervals of not greater than 0.5 m, the following clearly legible and indelible identification markings consisting of characters, figures or symbols.
Markings. If permitted by applicable Law, on or reasonably promptly after the Delivery Date, Lessee will cause to be affixed to, and maintained in, the cockpit of the Airframe and on each Engine, in each case, in a clearly visible location (it being understood that the location of such placards, as identified to the Owner Participant prior to the Delivery Date, shall be deemed to be in compliance with this requirement), a placard of a reasonable size and shape bearing the legend, in English, set forth in Schedule 6. Such placards may be removed temporarily, if necessary, in the course of maintenance of the Airframe or Engines. If any such placard is damaged or becomes illegible, Lessee shall promptly replace it with a placard complying with the requirements of this Section 7.1.3.
Markings. 4.1. The components of the sound reduction system, excluding fixing hardware and piping, shall bear:
4.1.1. The trade name or mark of the manufacturer of the sound reduction system and of its components; and
4.1.2. The manufacturer's trade description;
4.2. These markings shall be clearly legible and be indelible even after fitting.
4.3. A component may carry several approval numbers if it has been approved as component of several replacement silencing systems.
Markings. The samples of a type of reversing lamp submitted for approval shall:
3.1. bear the trade name or xxxx of the applicant; this marking shall be clearly legible and be indelible;
3.2. with the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating:
(a) the category or categories of filament lamp(s) prescribed; and/or
(b) the light source module specific identification code.
3.3. if necessary in order to prevent any mistake in mounting the reversing lamp on the vehicle, bear the word "TOP" marked horizontally on the uppermost part of the illuminating surface;
3.4. provide adequate space for the approval xxxx and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawing referred to in paragraph 2.2.1. above;
3.5. in the case of lamps with non-replaceable light sources or light source module(s), bear the marking of rated voltage or the range of voltage, and the rated wattage.
3.6. in the case of lamps with light source module(s), the light source module(s) shall bear:
3.6.1. the trade name or xxxx of the applicant; this marking must be clearly legible and indelible;
3.6.2. the specific identification code of the module; this marking must be clearly legible and indelible.
3.1.1. below; this specific identification code shall be shown in the drawings mentioned in paragraph 2.
2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant.
3.6.3. the marking of the rated voltage and rated wattage.
Markings. Rear fog lamps submitted for approval shall:
3.1. Bear the trade name or xxxx of the applicant; this marking must be clearly legible and be indelible;
3.2. With the exception of lamps with non-replaceable light sources bear a clearly legible and indelible marking indicating:
(a) The category or categories of light source prescribed; and/or
(b) The light source module specific identification code.
3.3. Provide adequate space for the approval xxxx and for the additional symbols prescribed in paragraph 4.3. below; the said space shall be shown in the drawings referred to in paragraph 2.2.1. above.
3.4. In the case of lamps with an electronic light source control gear or a variable intensity control and/or non-replaceable light sources and/or light source module(s), bear the marking of the rated voltage or range of voltage.
3.5. In the case of lamps with light source module(s), the light source module(s) shall bear:
3.5.1. The trade name or xxxx of the applicant; this marking must be clearly legible and indelible;
3.5.2. The specific identification code of the module; this marking must be clearly legible and indelible. This specific identification code shall comprise the starting letters "MD" for "MODULE" followed by the approval marking without the circle as prescribed in paragraph 4.
3.1.1. below and, in the case several non identical light source modules are used, followed by additional symbols or characters; this specific identification code shall be shown in the drawings mentioned in paragraph 2.2.1. above. The approval marking does not have to be the same as the one on the lamp in which the module is used, but both markings shall be from the same applicant.
3.5.3. The marking of the rated voltage or range of voltage.
3.6. An electronic light source control gear or a variable intensity control being part of the lamp but not included into the lamp body shall bear the name of the manufacturer and its identification number.
Markings. 4.1. The components of the AVAS (if applicable) shall bear:
4.1.1. The trade name or mark of the manufacturer(s) of the AVAS components;
4.1.2. A designated identification number(s).
4.2. These markings shall be clearly legible and be indelible.
Markings. 1.8.1. Every hose must bear, at intervals of not greater than 0.5 m, the following clearly legible and indelible identification markings consisting of characters, figures or symbols.
1.8.1.1. The trade name or mark of the manufacturer.
1.8.1.2. The year and month of fabrication.
1.8.1.3. The size and type-marking.
1.8.1.4. The identification marking "L.P.G. Class 1".
1.8.2. Every coupling shall bear the trade name or mark of the assembling manufacturer.
Markings. The samples of a belt type or type of restraint system submitted for approval in conformity with the provisions of paragraphs 3.2.2.2., 3.2.2.3. and 3.2.2.4. above shall be clearly and indelibly marked with the manufacturer's name, initials or trade name or xxxx.
Markings. 5.1. An approval number shall be assigned to each vehicle or ESA type approved. The first two digits of this number (at present 06) shall indicate the series of amendments corresponding to the most recent essential technical amendments made to the Regulation at the date of approval. A Contracting Party may not assign the same approval number to another type of vehicle or ESA.
5.2. Presence of markings