Common use of Inspection Precautions Clause in Contracts

Inspection Precautions. (1) DS810 / DS810 Plus can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage. (2) Use only the power cord supplied with the IDUTEX diagnostics or detected power line. (3) Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure. (4) Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in a well ventilated area before operation. (5) Do not place the device on the vehicle's power distribution unit. Strong electromagnetic interference can cause damage to the equipment. (6) After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started. (7) When the engine is running at a high temperature, avoid contact with high temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit and the ignition plug during engine operation.

Inspection Precautions. (1) DS810 / DS810 Plus Xxxxx X6/X7 can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage. (2) Use only the power cord supplied with the IDUTEX OBDSPACE diagnostics or detected power line. (3) Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure. (4) Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in a well ventilated area before operation. (5) Do not place the device on the vehicle's power distribution unit. Strong electromagnetic interference can cause damage to the equipment. (6) After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started. (7) When the engine is running at a high temperature, avoid contact with high temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit and the ignition plug during engine operation.

Inspection Precautions. (1) DS810 / DS810 Plus Xxxxx V6 Series can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage. (2) Use only the power cord supplied with the IDUTEX OBDSPACE diagnostics or detected power line. (3) Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure. (4) Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in a well ventilated area before operation. (5) Do not place the device on the vehicle's power distribution unit. Strong electromagnetic interference can cause damage to the equipment. (6) After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started. (7) When the engine is running at a high temperature, avoid contact with high temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit and the ignition plug during engine operation.

Inspection Precautions. ‌ (1) DS810 Xxxxx X6 HD / DS810 Plus X7 HD can only be connected to a safety outlet that is grounded. Before connecting, check and confirm that the diagnostic circuit is in good condition. Otherwise, it is not necessary to test to avoid damage to the main unit. If necessary, use a multimeter to measure the diagnostic seat voltage. (2) Use only the power cord supplied with the IDUTEX OBDSPACE diagnostics or detected power line. (3) Pay special attention to the effects or damage caused by environmental factors such as acid and alkali, poison gas, and heavy pressure. (4) Exhaust gases from the engine contain a variety of toxic compounds and should be avoided. Park the vehicle in a well ventilated area before operation. (5) Do not place the device on the vehicle's power distribution unit. Strong electromagnetic interference can cause damage to the equipment. (6) After the equipment is installed successfully, before starting the engine, make sure that the parking brake is pulled and the speed lever is placed in the neutral or parked position to avoid accidents when the vehicle is started. (7) When the engine is running at a high temperature, avoid contact with high temperature components such as the water tank and the exhaust pipe. At the same time, be careful of the voltage generated by the components such as the ignition coil, the distributor cover, the ignition circuit and the ignition plug during engine operation.