Manual Activation Sample Clauses

Manual Activation. The radio module can be configured to transmit a short packetized control signal if triggered manually. The module can be triggered by pressing a switch, for example. The packet contains one (or more) control signals that is (are) intended to control something at the receiving end. The packet may also contain data. Depending on how much energy is available from the energy source, subsequent manual triggers can initiate the transmission of additional control signals. This may be necessary if prior packet(s) was (were) lost due to fading or interference. Subsequent triggers can also be initiated as a precaution if any doubt exists that the first packet didn’t arrive at the receiver. Each packet that is transmitted, regardless of whether it was the first one or a subsequent one, will only be transmitted if enough energy is available from the energy source.
Sample 1Sample 2
AutoNDA by SimpleDocs
Manual Activation. If you do not have an Internet connection, or if you experience any difficulty using the Automatic option, you can activate your software manually. Click Manual and skip to the section titled Manual Activation. AUTOMATIC ACTIVATION‌ Once the automatic activation process is completed successfully, you will see the Software Registration Wizard Completed screen. If you see this screen, skip to the Completing the Registration section.
Sample 1

Related to Manual Activation

  • Activation We will notify the Xxxxxx of your request to receive electronic billing information. The presentment of your first electronic bill may vary from Xxxxxx to Xxxxxx and may take up to sixty (60) days, depending on the billing cycle of each Xxxxxx. While your electronic bill feature is being activated it is your responsibility to keep your accounts current. Each electronic Xxxxxx reserves the right to accept or deny your request to receive electronic bills.

  • Service Activation For new customers - the services are activated immediately after successful processing of payment and our fraud detection software approves the order. The payment verification procedure is obligatory and if we fail to approve a transaction within 48 hours of the payment submission, the funds will be credited back to the payer and the order will be cancelled. Free Trials - All free trial orders are manually processed. If we deem your order to be suspicious or high risk, we will notify you and request additional information before process the order. Failure to comply with our request for more information will result in cancellation of the order. For existing customers - the services for existing customers, including upgrade services and renewals, are activated immediately after our Sales Department receives the according service payment.

  • Service Activation Date Billing for the Service Component will begin on the Service Activation Date, as specified below, for the specific Service type. The Service Activation Date is the date (i) Equipment is installed and tested at the Customer’s locations, and (ii) IP connectivity to LightEdge has been established.

  • No-­‐Activation Period Registry Operator shall not activate any names in the DNS zone for the Registry TLD (except for "NIC") until at least 120 calendar days after the effective date of this agreement. Registry Operator may allocate names (subject to subsection 6.2 below) during this period only if Registry Operator causes registrants to be clearly informed of the inability to activate names until the No-­‐Activation Period ends.

  • Deactivation Computershare applications shall automatically deactivate a User ID after a specified number of unsuccessful log-in attempts. Sessions must be restricted or timed out after a defined period of inactivity and require Users to re-authenticate. User IDs for Computershare Personnel with access to Customer Confidential Information shall be deactivated immediately upon changes in job responsibilities that render such access unnecessary, or upon termination of employment.

  • Other Methods of Procurement of Consultants’ Services The following table specifies methods of procurement, other than Quality and Cost-based Selection, which may be used for consultants’ services. The Procurement Plan shall specify the circumstances under which such methods may be used. Procurement Method

  • Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers.

  • Processing of Grievance It is recognized and accepted by the Union and the County that the processing of grievances as hereinafter provided is limited by the job duties and responsibilities of the employees and shall therefore be accomplished during normal working hours only when consistent with such employee duties and responsibilities. The aggrieved employee's representative, if an employee, shall be allowed a reasonable amount of time without loss in pay, to investigate a grievance, and present grievances to the County during normal working hours provided the employee and the employee representative have notified the designated supervisor.

  • Particular Methods of Procurement of Consultants’ Services 1. Quality- and Cost-based Selection. Except as otherwise provided in paragraph 2 below, consultants’ services shall be procured under contracts awarded on the basis of Quality and Cost-based Selection.

  • Terminating Switched Access Detail Usage Data A category 1101XX record as defined in the EMI Telcordia Practice BR-010-200- 010.

Time is Money Join Law Insider Premium to draft better contracts faster.