Manufacture and Supply As between the Parties, Otsuka shall be responsible for, shall bear all costs associated with, and shall have all decision-making authority over, all Manufacturing Activities (subject to discussion of CMC matters with Acucela through the JDC or applicable Operating Team as discussed below); provided, that Otsuka shall supply Licensed Product to Acucela or its permitted subcontractors for use in clinical trials conducted in accordance with each Development Plan and, if applicable, Commercialization Plan (i.e., Phase 3b Clinical Trials or Post-Approval Studies, if any), free of charge and in such quantities as are agreed by the JDC or the JCC (as applicable) or are otherwise required to seek or obtain Regulatory Approval. In addition, if and after Acucela exercises an Opt-In Right under Section 3.1, Otsuka shall supply promotional samples of Licensed Product to Acucela for use in its performance of Co-Promotion, in such quantities and on such terms as are determined by the JCC. The cost of promotional samples of Licensed Product, which shall be included in Commercialization Costs, shall be established by the JCC based on Otsuka’s per-unit cost to manufacture such promotional samples (but, for the avoidance of doubt, Otsuka shall have no obligation to disclose any information relating to its manufacturing costs), but in no event shall such promotional sample cost exceed * per promotional sample unless mutually agreed otherwise by the Parties. Acucela’s and its permitted subcontractors’ obligations to conduct Development activities, and upon Acucela’s exercise of its Opt-in Right pursuant to Section 3.1, to conduct Development and Commercialization activities, shall be expressly conditioned upon Otsuka fulfilling its Licensed Product supply obligations as set forth in the Development Plan or the Commercialization Plan, as applicable. To the extent that Otsuka reasonably believes is necessary for performance of Development or Commercialization, Otsuka agrees to keep Acucela reasonably informed from time to time, through the JDC, JCC or applicable Operating Team, regarding the general status of Manufacturing Activities related to the Licensed Product (including Other Indication Product(s), as applicable) and from time to time shall update Acucela on any foreseeable delays and/or other material issues relating to Manufacturing the Licensed Product (including Other Indication Product(s), as applicable). Through the JDC or applicable Operating Team, Otsuka and Acucela shall confer and discuss CMC matters, and Otsuka agrees to consider suggestions of Acucela regarding CMC matters.
Licensed Products Lessee will obtain no title to Licensed Products which will at all times remain the property of the owner of the Licensed Products. A license from the owner may be required and it is Lessee's responsibility to obtain any required license before the use of the Licensed Products. Lessee agrees to treat the Licensed Products as confidential information of the owner, to observe all copyright restrictions, and not to reproduce or sell the Licensed Products.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.
Marking of Licensed Products To the extent commercially feasible and consistent with prevailing business practices, Company shall xxxx, and shall cause its Affiliates and Sublicensees to xxxx, all Licensed Products that are manufactured or sold under this Agreement with the number of each issued patent under the Patent Rights that applies to such Licensed Product.
Licensed Product The term “Licensed Product” shall mean any product (a) the manufacture, use, importation, sale or offer for sale of which would, in the absence of the license granted by this Agreement, infringe a Valid Claim of any of the Licensed Patent Rights, or (b) that is comprised of, utilizes or incorporates Licensed Biological Materials, or (c) that is discovered, developed or made using a Licensed Process.
Manufacture of Products All Products marketed through Grantor's Web ------------------------- Site shall be manufactured, packaged, prepared, and shipped in accordance with the specifications and requirements described on Exhibit A hereto as it may be modified from time to time. Quality control standards relating to the Product's weight, color, consistency, micro-biological content, labeling and packaging are also set forth on Exhibit A. In the event that Exhibit A is incomplete, Products shall be manufactured and shipped in accordance with industry standards.
Existing Products Except as set forth below, Contractor shall retain all rights, title and interest in Existing Products.
Manufacture 2.1. The LED(s) on the LED module shall be equipped with suitable fixation elements.
2.2. The fixation elements shall be strong and firmly secured to the LED(s) and the LED module.
API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.
