Common use of Measurement Devices Clause in Contracts

Measurement Devices. (a) All Gas and Injected Liquids Tendered hereunder at a Receipt Points shall be measured, prior to delivery into the Gathering System, by a suitable measurement device to be furnished and installed (or caused to be furnished and installed) by Gatherer, and subsequently kept in repair (or caused to be kept in repair) by Gatherer, and located at or near such Receipt Point. Such Gas measurement devices shall be installed, and the meter run fabricated and installed, in accordance with the American Petroleum Institute Manual of Petroleum Measurement Standards (the “MPMS”) Chapter 14.3, Part 2 April 2000, Reaffirmed May 2011, utilizing EGM (electronic gas measurement) installed pursuant to MPMS Chapter 21.1, August 1993, Reaffirmed August 2011. Such Injected Liquids Turbine or Coriolis measurement devices shall be installed in accordance with the MPMS Chapter 5.3, November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter, or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**). (b) Gas metered hereunder shall be computed in units of Mcf and Injected Liquids metered hereunder shall be computed in units of MCFE. Such Gas shall be measured in accordance with the MPMS Chapter 14.3, Part 3 August 1992, Reaffirmed February 2009, and such Injected Liquids shall be measured in accordance with the MPMS, Chapter 5.3 November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters, in each case, as the same may be amended from time to time, in a manner generally accepted by the gas producing industry, with the following exception: the atmospheric pressure used by Gatherer where Gas and Injected Liquids are measured shall be as set prescribed by the Standard Base Conditions. (c) Gatherer shall inspect (or cause to be inspected) said measurement devices semi-annually, and adjust and repair (or caused to be adjusted and repaired) the same as necessary. Gatherer shall notify Shipper in writing prior to such measurement device calibrations in order that Shipper may have a representative present to witness same, and the measurement device(s) shall be open to inspection at all times by Shipper in the presence of Gatherer. In case any question arises as to the accuracy of the measurement, said measurement devices shall be tested upon the demand of either Party. The expense of such tests shall be borne by the Party demanding same if the measurement device is found to be correct, and by Gatherer if found incorrect. A registration within one percent (1.0%) of correct shall be considered correct, but the measurement device shall be adjusted to zero error. Settlement for any period of inoperable or inaccurate measurement shall be in accordance with the average readings taken during the last preceding ten Days when the measurement device was registering accurately and the first ten Days after the measurement device was restored to accuracy. If Gatherer and Seller are unable to agree as to the time period during which the measurement device was inoperative or inaccurate it is agreed that volume adjustments shall be limited to no more than one-half of the operational Days from the date of the last calibration to the date of the correct calibration. (d) If the measurement equipment is found to be measuring inaccurately and the amount of Gas delivered cannot be ascertained or computed from the reading, then the Gas and Injected Liquids delivered will be estimated and agreed upon by the Parties based on the best data available, using the first available of the following: (i) The registration of any check meter or meters if installed and accurately registering; (ii) The correction of the errors, if the percentage of error is ascertainable by meter calibration, test, or mathematical calculation; (iii) The estimation based on comparison of the quantity of deliveries with deliveries during preceding periods under similar conditions when the meter was registering accurately. (e) If requested, Gatherer shall send the charts or electronic data, as available to Gatherer, to Shipper for checking, after which they are to be returned to Gatherer within 90 Days. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**).

Measurement Devices. (a) All Gas and Injected Liquids Tendered hereunder at a Receipt Points shall be measured, prior to delivery into the Gathering System, by a suitable measurement device to be furnished and installed (or caused to be furnished and installed) by Gatherer, and subsequently kept in repair (or caused to be kept in repair) by Gatherer, and located at or near such Receipt Point. Such Gas measurement devices shall be installed, and the meter run fabricated and installed, in accordance with the American Petroleum Institute Manual of Petroleum Measurement Standards (the “MPMS”) Chapter 14.3, Part 2 April 2000, Reaffirmed May 2011, utilizing EGM (electronic gas measurement) installed pursuant to MPMS Chapter 21.1, August 1993, Reaffirmed August 2011. Such Injected Liquids Turbine or Coriolis measurement devices shall be installed in accordance with the MPMS Chapter 5.3, November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter, or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**). (b) Gas metered hereunder shall be computed in units of Mcf and Injected Liquids metered hereunder shall be computed in units of MCFE. Such Gas shall be measured in accordance with the MPMS Chapter 14.3, Part 3 August 1992, Reaffirmed February 2009, and such Injected Liquids shall be measured in accordance with the MPMS, Chapter 5.3 November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters, in each case, as the same may be amended from time to time, in a manner generally accepted by the gas producing industry, with the following exception: the atmospheric pressure used by Gatherer where Gas and Injected Liquids are measured shall be as set prescribed by the Standard Base Conditions. (c) Gatherer shall inspect (or cause to be inspected) said measurement devices semi-annually, and adjust and repair (or caused to be adjusted and repaired) the same as necessary. Gatherer shall notify Shipper in writing prior to such measurement device calibrations in order that Shipper may have a representative present to witness same, and the measurement device(s) shall be open to inspection at all times by Shipper in the presence of Gatherer. In case any question arises as to the accuracy of the measurement, said measurement devices shall be tested upon the demand of either Party. The expense of such tests shall be borne by the Party demanding same if the measurement device is found to be correct, and by Gatherer if found incorrect. A registration within one percent (1.0%) of correct shall be considered correct, but the measurement device shall be adjusted to zero error. Settlement for any period of inoperable or inaccurate measurement shall be in accordance with the average readings taken during the last preceding ten Days when the measurement device was registering accurately and the first ten Days after the measurement device was restored to accuracy. If Gatherer and Seller are unable to agree as to the time period during which the measurement device was inoperative or inaccurate it is agreed that volume adjustments shall be limited to no more than one-half of the operational Days from the date of the last calibration to the date of the correct calibration. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**). (d) If the measurement equipment is found to be measuring inaccurately and the amount of Gas delivered cannot be ascertained or computed from the reading, then the Gas and Injected Liquids delivered will be estimated and agreed upon by the Parties based on the best data available, using the first available of the following: (i) The registration of any check meter or meters if installed and accurately registering; (ii) The correction of the errors, if the percentage of error is ascertainable by meter calibration, test, or mathematical calculation; (iii) The estimation based on comparison of the quantity of deliveries with deliveries during preceding periods under similar conditions when the meter was registering accurately. (e) If requested, Gatherer shall send the charts or electronic data, as available to Gatherer, to Shipper for checking, after which they are to be returned to Gatherer within 90 Days. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**).

Measurement Devices. (a) All Gas and Injected Liquids Tendered hereunder at a Receipt Points shall be measured, prior to delivery into the Gathering System, by a suitable measurement device to be furnished and installed (or caused to be furnished and installed) by Gatherer, and subsequently kept in repair (or caused to be kept in repair) by Gatherer, and located at or near such Receipt Point. Such Gas measurement devices shall be installed, and the meter run fabricated and installed, in accordance with the American Petroleum Institute Manual of Petroleum Measurement Standards (the “"MPMS”") Chapter 14.3, Part 2 April 2000, Reaffirmed May 2011, utilizing EGM (electronic gas measurement) installed pursuant to MPMS Chapter 21.1, August 1993, Reaffirmed August 2011. Such Injected Liquids Turbine or Coriolis measurement devices shall be installed in accordance with the MPMS Chapter 5.3, November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter, or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**). (b) Gas metered hereunder shall be computed in units of Mcf and Injected Liquids metered hereunder shall be computed in units of MCFE. Such Gas shall be measured in accordance with the MPMS Chapter 14.3, Part 3 August 1992, Reaffirmed February 2009, and such Injected Liquids shall be measured in accordance with the MPMS, Chapter 5.3 November 2011, Measurement of Liquid Hydrocarbons by Turbine Meter or MPMS Chapter 5.6 October 202, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters, in each case, as the same may be amended from time to time, in a manner generally accepted by the gas producing industry, with the following exception: the atmospheric pressure used by Gatherer where Gas and Injected Liquids are measured shall be as set prescribed by the Standard Base Conditions. (c) Gatherer shall inspect (or cause to be inspected) said measurement devices semi-annually, and adjust and repair (or caused to be adjusted and repaired) the same as necessary. Gatherer Xxxxxxxx shall notify Shipper in writing prior to such measurement device calibrations in order that Shipper Xxxxxxx may have a representative present to witness same, and the measurement device(s) shall be open to inspection at all times by Shipper Xxxxxxx in the presence of Gatherer. In case any question arises as to the accuracy of the measurement, said measurement devices shall be tested upon the demand of either Party. The expense of such tests shall be borne by the Party demanding same if the measurement device is found to be correct, and by Gatherer if found incorrect. A registration within one percent (1.0%) of correct shall be considered correct, but the measurement device shall be adjusted to zero error. Settlement for any period of inoperable or inaccurate measurement shall be in accordance with the average readings taken during the last preceding ten Days when the measurement device was registering accurately and the first ten Days after the measurement device was restored to accuracy. If Gatherer Xxxxxxxx and Seller are unable to agree as to the time period during which the measurement device was inoperative or inaccurate it is agreed that volume adjustments shall be limited to no more than one-half of the operational Days from the date of the last calibration to the date of the correct calibration. CERTAIN CONFIDENTIAL PORTIONS OF THIS EXHIBIT WERE OMITTED BY MEANS OF MARKING SUCH PORTIONS WITH BRACKETS (“[***]”) BECAUSE THE IDENTIFIED CONFIDENTIAL PORTIONS (I) ARE NOT MATERIAL AND (II) IS THE TYPE OF INFORMATION THAT THE REGISTRANT TREATS AS PRIVATE OR CONFIDENTIAL. (d) If the measurement equipment is found to be measuring inaccurately and the amount of Gas delivered cannot be ascertained or computed from the reading, then the Gas and Injected Liquids delivered will be estimated and agreed upon by the Parties based on the best data available, using the first available of the following: (i) The registration of any check meter or meters if installed and accurately registering; (ii) The correction of the errors, if the percentage of error is ascertainable by meter calibration, test, or mathematical calculation; (iii) The estimation based on comparison of the quantity of deliveries with deliveries during preceding periods under similar conditions when the meter was registering accurately. (e) If requested, Gatherer shall send the charts or electronic data, as available to Gatherer, to Shipper for checking, after which they are to be returned to Gatherer within 90 Days. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**).

Measurement Devices. (a) All Gas Crude Oil and Injected Liquids NGLs Tendered hereunder at a Receipt Points and Delivery Points shall be measured, prior to delivery into the Gathering System, measured by a suitable measurement device Measurement Device to be furnished and installed (or caused to be furnished and installed) by GathererProvider, and subsequently kept in repair (or caused to be kept in repair) by GathererProvider, and located at or near such Receipt PointPoints and Delivery Points. Such Gas measurement devices Measurement Devices shall be installed, and the meter run fabricated and installed, operated in accordance with the American Petroleum Institute Manual of Petroleum Measurement Standards (the “"MPMS”") Chapter 14.3, Part 2 April 20005.2 Measurement of Liquid Hydrocarbons by Displacement Meters October 2005, Reaffirmed May 2011September 2010, utilizing EGM (electronic gas measurement) installed pursuant to MPMS and/or Chapter 21.1, August 19935.6 Measurement of liquid Hydrocarbons by Coriolis Meters October 2002, Reaffirmed August 2011March 2008, and/or Chapter 5.3 Measurement of Liquid Hydrocarbons by Turbine Meters September 2005 (including Addendum 1 dated 2009) and all amendments and supplements thereto prior to the date of such installation. (b) For Crude Oil in determining the amount of sediment, water, or other impurities and the API Gravity for each Unit Train, the Terminals System shall utilize a proportion to flow composite sampler. Such Injected Liquids Turbine or Coriolis measurement devices For NGLs in determining the component analysis when required, the Terminals System shall utilize a proportion to flow composite sampler. The sampling device shall be installed installed, and operated in accordance with the MPMS Chapter 5.3, November 2011, Measurement 8.2 Standard Practice of Automatic Sampling of Liquid Hydrocarbons by Turbine MeterPetroleum and Petroleum products Second Edition, or MPMS Chapter 5.6 October 2021995, Reaffirmed Reaffirmed, March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters2010. TERMS IN THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS (**). (b) Gas metered hereunder All samples shall be computed in units of Mcf mixed and Injected Liquids metered hereunder shall be computed in units of MCFE. Such Gas shall be measured handled in accordance with the MPMS Chapter 14.3, Part 3 August 1992, Reaffirmed February 2009, 8.3 Standard Practice for Mixing and such Injected Liquids shall be measured in accordance with the MPMS, Chapter 5.3 November 2011, Measurement Handling of Liquid Hydrocarbons by Turbine Meter or MPMS Chapter 5.6 Samples of Petroleum and Petroleum Products First Edition, October 2021995, Reaffirmed March 2008, Measurement of Liquid Hydrocarbons by Coriolis Meters, in each case, as the same may be amended from time to time, in a manner generally accepted by the gas producing industry, with the following exception: the atmospheric pressure used by Gatherer where Gas and Injected Liquids are measured shall be as set prescribed by the Standard Base Conditions. (c) Gatherer shall inspect (or cause to be inspected) said measurement devices semi-annually, and adjust and repair (or caused to be adjusted and repaired) the same as necessary2010. Gatherer shall notify Shipper in writing prior to such measurement device calibrations in order that Shipper may have a representative present to witness same, and the measurement device(s) shall be open to inspection at all times by Shipper in the presence of Gatherer. In case any question arises as to the accuracy of the measurement, said measurement devices shall be tested upon the demand of either Party. The expense of such tests shall be borne by the Party demanding same if the measurement device is found to be correct, and by Gatherer if found incorrect. A registration within one percent (1.0%) of correct shall be considered correct, but the measurement device shall be adjusted to zero error. Settlement for any period of inoperable or inaccurate measurement shall be in accordance with the average readings taken during the last preceding ten Days when the measurement device was registering accurately and the first ten Days after the measurement device was restored to accuracy. If Gatherer and Seller are unable to agree as to the time period during which the measurement device was inoperative or inaccurate it is agreed that volume adjustments shall be limited to no more than one-half of the operational Days from the date of the last calibration to the date of the correct calibration. (d) If the measurement equipment is found to be measuring inaccurately and the amount of Gas delivered cannot be ascertained or computed from the reading, then the Gas and Injected Liquids delivered will be estimated and agreed upon by the Parties based on the best data available, using the first available of the following: (i) The registration of any check meter or meters if installed and accurately registering; (ii) The correction of the errors, if the percentage of error is ascertainable by meter calibration, test, or mathematical calculation; (iii) The estimation based on comparison of the quantity of deliveries with deliveries during preceding periods under similar conditions when the meter was registering accurately. (e) If requested, Gatherer shall send the charts or electronic data, as available to Gatherer, to Shipper for checking, after which they are to be returned to Gatherer within 90 Days. TERMS IN CERTAIN CONFIDENTIAL PORTIONS OF THIS EXHIBIT HAVE BEEN REDACTED BECAUSE CONFIDENTIAL TREATMENT FOR THOSE TERMS HAS BEEN REQUESTED. THE REDACTED MATERIAL HAS BEEN FILED SEPARATELY WERE OMITTED BY MEANS OF MARKING SUCH PORTIONS WITH THE SECURITIES AND EXCHANGE COMMISSION, AND THE TERMS HAVE BEEN MARKED AT THE APPROPRIATE PLACE WITH TWO ASTERISKS BRACKETS (“[**)*]”) BECAUSE THE IDENTIFIED CONFIDENTIAL PORTIONS (I) ARE NOT MATERIAL AND (II) IS THE TYPE OF INFORMATION THAT THE REGISTRANT TREATS AS PRIVATE OR CONFIDENTIAL.