Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Settlement Method For any Option, Net Share Settlement; provided that if the Relevant Settlement Method set forth below for such Option is not Net Share Settlement, then the Settlement Method for such Option shall be such Relevant Settlement Method, but only if Counterparty shall have notified Dealer of the Relevant Settlement Method in the Notice of Final Settlement Method for such Option.
Settlement Method Election Date The third Scheduled Trading Day immediately preceding the First Expiration Date.
Settlement Method Election Physical Settlement, Cash Settlement, or Net Share Settlement, at the election of Counterparty as set forth in a Settlement Notice that satisfies the Settlement Notice Requirements; provided that Physical Settlement shall apply (i) if no Settlement Method is validly selected, (ii) with respect to any Settlement Shares in respect of which Dealer is unable, in good faith and in its commercially reasonable discretion, to unwind its commercially reasonable hedge by the end of the Unwind Period (taking into account any Additional Transactions with overlapping “Unwind Periods” (as defined in the applicable Additional Confirmations)) (A) in a manner that, in the reasonable discretion of Dealer, based on advice of counsel, is consistent with the requirements for qualifying for the safe harbor provided by Rule 10b-18 under the Exchange Act (“Rule 10b-18”) or (B) in its commercially reasonable judgment, due to the occurrence of five or more Disrupted Days or to the lack of sufficient liquidity in the Shares on any Exchange Business Day during the Unwind Period, (iii) to any Termination Settlement Date (as defined under “Termination Settlement” in Paragraph 7(g) below) and (iv) if the Final Date is a Settlement Date other than as the result of a valid Settlement Notice, in respect of such Settlement Date; provided, further, that, if Physical Settlement applies under clause (ii) immediately above, Dealer shall provide written notice to Counterparty at least two Scheduled Trading Days prior to the applicable Settlement Date.
Procurement Method Quality-Based Selection (b) Selection under a Fixed Budget
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C.
1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Payment Method Payment shall be made by the Contractor to the Subcontractor as follows: (choose one) ☐ - Immediately upon completion of the Services to the satisfaction of the Contractor. ☐ - Within ____ business days after completion of the Services to the satisfaction of the Contractor. ☐ - Shall be paid on a ☐ weekly ☐ monthly ☐ quarterly ☐ other ______________________ basis. If the Subcontractor completes the Services to the satisfaction of the Contractor, before the full amount or balance has been fully paid, any remaining amount shall be payable immediately. ☐ - Other: ________________________________________________________
Test method This test is intended to demonstrate the immunity of the vehicle electronic systems. The vehicle shall be subject to electromagnetic fields as described in this annex. The vehicle shall be monitored during the tests. If not otherwise stated in this annex the test shall be performed according to ISO 11451-2.
Payment Methods A. Except as otherwise provided by this Contract, the payment method will be one or more of the following:
First Method and Market Quotation If the First Method and Market Quotation apply, the Defaulting Party will pay to the Non-defaulting Party the excess, if a positive number, of (A) the sum of the Settlement Amount (determined by the Non-defaulting Party) in respect of the Terminated Transactions and the Termination Currency Equivalent of the Unpaid Amounts owing to the Non-defaulting Party over (B) the Termination Currency Equivalent of the Unpaid Amounts owing to the Defaulting Party.
