Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 493 contracts
Samples: Construction Contract, Epc Agreement, Engineering Procurement and Construction Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 33 contracts
Samples: Engineering Procurement and Construction (Epc) Agreement, Engineering Procurement and Construction Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 two (two2) decimal places, with the third digit of 5 five (five5) or above being rounded up and below 5 five (five5) being rounded down.
Appears in 24 contracts
Samples: Power Purchase Agreement, Power Purchase Agreement, Power Purchase Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in money calculations where such amounts shall be rounded off to the nearest INR.
Appears in 15 contracts
Samples: Master Service Agreement, Master Service Agreement, Master Services Agreement and Service Level Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in money calculation which shall be rounded off to nearest rupee.
Appears in 13 contracts
Samples: Concession Agreement, License Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 13 contracts
Samples: Operation and Maintenance Agreement, Operation and Maintenance Agreement, Operation and Maintenance Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down; provided that the drawings, engineering dimensions and tolerances may exceed 2 (two) decimal places as required.
Appears in 10 contracts
Samples: Concession Agreement, Concession Agreement, Manufacturing Cum Maintenance Agreement
Measurements and arithmetic conventions. 1.3.1 All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 9 contracts
Samples: Concession Agreement, Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. (a) All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 6 contracts
Samples: Concession Agreement, Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All Unless otherwise specified, all measurements and calculations under this Agreement shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 6 contracts
Samples: Power Purchase Agreement, Power Purchase Agreement, Energy Supply and Purchase Agreement
Measurements and arithmetic conventions. 1.3.1. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 6 contracts
Samples: Concession Agreement, Concession Agreement, Operation & Maintenance Agreement
Measurements and arithmetic conventions. 1.3.1 All measurements and calculations shall be in the metric system and calculations done up to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 5 contracts
Samples: Lease Cum Development Agreement, Lease Cum Development Agreement, Lease Cum Development Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to in 2 (two) decimal decimals places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 5 contracts
Samples: Concession Agreement, Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down; provided that the drawings, engineering dimensions and tolerances may exceed 2 (two) decimal places, if required.
Appears in 5 contracts
Samples: Contract Agreement, Contract Agreement, Model Contract Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up roundedup and below 5 (five) being rounded down.
Appears in 5 contracts
Samples: Construction Contract, Contract Agreement, Construction Contract
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) two decimal places, with the third digit of 5 (five) five or above being rounded up and below 5 (five) five being rounded downdown except in money calculations where such amounts shall be rounded off to the nearest INR.
Appears in 5 contracts
Samples: Master Service Agreement, Master Service Agreement, Master Services Agreement
Measurements and arithmetic conventions. [All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in money calculations where such amounts shall be rounded off to the nearest INR.]
Appears in 3 contracts
Samples: Master Service Agreement, Master Service Agreement (Msa) and Service Level Agreement (Sla), Master Services Agreement
Measurements and arithmetic conventions. 2.2.1 All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 3 contracts
Samples: License Agreement, License Agreement, License Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 3 (twothree) decimal places, with the third fourth digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 3 contracts
Samples: Procurement Agreement, Power Purchase Agreement, Power Purchase Agreement
Measurements and arithmetic conventions. 1.3.1. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 3 contracts
Samples: Concession Agreement, Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 5 (twofive) decimal places, with the third sixth digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 3 contracts
Samples: Concession Agreement, Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third 3rd (third) digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 3 contracts
Samples: Development, Operation and Maintenance Agreement, Development, Operation and Maintenance Agreement, Development, Operation and Maintenance Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 2 contracts
Samples: License Agreement, Draft Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in Xxxxxxxxx Charges calculation which shall be rounded off to nearest rupee.
Appears in 2 contracts
Samples: Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down, provided that the drawings, engineering dimensions, and tolerances may exceed 2 (two) decimal places as required.
Appears in 2 contracts
Samples: Programme Agreement, Programme Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two2(two) decimal places, with the third digit of 5 (five5(five) or above being rounded up and below 5 (five5(five) being rounded down; provided that the drawings, engineering dimensions and tolerances may exceed 2 (two) decimal places, if required.
Appears in 2 contracts
Samples: Coal Mining Agreement, Coal Mining Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 2 contracts
Samples: Supply, Installation, Operation and Maintenance Agreement, Supply, Installation, Operation and Maintenance Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in money calculations, which shall be rounded off to nearest Rupee.
Appears in 2 contracts
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down; provided that the drawings, engineering dimensions and tolerances may exceed 2 (two) decimal places, if required.
Appears in 2 contracts
Samples: Contract Agreement, Coal Mining Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five5(five) being rounded down.
Appears in 2 contracts
Samples: Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal placesdecimalplaces, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 2 contracts
Samples: Concession Agreement, Concession Agreement
Measurements and arithmetic conventions. 1.4.1 All measurements and calculations shall be in the metric system and calculations done to 2 two (two2) decimal places, with the third digit of 5 five (five5) or above being rounded up and below 5 five (five5) being rounded down.
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above after the decimal being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Implementation Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) two decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Operations & Maintenance Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.down except in money calculations where such amounts shall be rounded off to the nearest INR. In case of ambiguities or discrepancies within this Agreement, the following principles shall apply:
Appears in 1 contract
Samples: Contract Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down; provided that the Drawings, engineering dimensions and tolerances may exceed 2 (two) decimal places, if required.
Appears in 1 contract
Samples: Coal Mining Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below be- low 5 (five) being rounded down.
Appears in 1 contract
Samples: Construction Contract
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to upto 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Epc Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdown except in money calculations where such amounts shall be rounded off to the nearest figure and all the price and calculations should be in INR.
Appears in 1 contract
Samples: Contract Agreement for Selection of System Integrators
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) 3 decimal places, with the third fourth digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Power Purchase Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.. In case of ambiguities or discrepancies within this Agreement, the following shall apply:
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 two (two2) decimal places, with the third digit of 5 five (five5) or above being rounded up and below 5 five (five5) being rounded down, except in money calculation which shall be rounded off to nearest rupee.
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. 2.3.1 All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: License Agreement
Measurements and arithmetic conventions. 1.4.1 All measurements and calculations shall be in the metric system and calculations done to 2 two (two2) decimal places, with the third digit of 5 five (five5) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third th ird digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. 1.3.1. All measurements and calculations shall be in the metric system and calculations done to 2 two (two2) decimal places, with the third digit of 5 five (five5) or above being rounded up and below 5 five (five5) being rounded down.
Appears in 1 contract
Samples: Operation & Maintenance Agreement
Measurements and arithmetic conventions. a) All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Appears in 1 contract
Samples: Concession Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded downdownexcept in money calculations where such amounts shall be rounded off to the nearest INR.
Appears in 1 contract
Samples: Service Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.. Priority of agreements and errors/discrepancies
Appears in 1 contract
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.;
Appears in 1 contract
Samples: License Cum Development Agreement
Measurements and arithmetic conventions. All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 below5 (five) being rounded down.
Appears in 1 contract
Samples: Concession Agreement
