MGC/MGW Naming Conventions. No change.
MGC/MGW Naming Conventions Sample Clauses
Related to MGC/MGW Naming Conventions
File Naming Conventions Files will be named according to the following convention: {gTLD}_{YYYY-MM-DD}_{type}_S{#}_R{rev}.{ext} where: {gTLD} is replaced with the gTLD name; in case of an IDN-TLD, the ASCII-compatible form (A-Label) must be used; {YYYY-MM-DD} is replaced by the date corresponding to the time used as a timeline watermark for the transactions; i.e. for the Full Deposit corresponding to 2009-08-02T00:00Z, the string to be used would be “2009-08-02”; {type} is replaced by: “full”, if the data represents a Full Deposit; “diff”, if the data represents a Differential Deposit; “thin”, if the data represents a Bulk Registration Data Access file, as specified in Section 3 of Specification 4; {#} is replaced by the position of the file in a series of files, beginning with “1”; in case of a lone file, this must be replaced by “1”. {rev} is replaced by the number of revision (or resend) of the file beginning with “0”: {ext} is replaced by “sig” if it is a digital signature file of the quasi-homonymous file. Otherwise it is replaced by “ryde”.
Union Conventions Subject to the approval of the supervisor(s) concerned, and upon written request submitted at least twenty (20) working days in advance, leave of absence without pay shall be granted to not more than two (2) employees at any one time, who may be elected or selected by the Union to attend any authorized labour convention. Such leave of absence is to be confined to the actual duration of the convention and the necessary travelling time. Such leave shall not exceed ten (10) working days per year for each employee to whom such leave is granted.
Limitation on Out-of-State Litigation - Texas Business and Commerce Code § 272 This is a requirement of the TIPS Contract and is non-negotiable. Texas Business and Commerce Code § 272 prohibits a construction contract, or an agreement collateral to or affecting the construction contract, from containing a provision making the contract or agreement, or any conflict arising under the contract or agreement, subject to another state’s law, litigation in the courts of another state, or arbitration in another state. If included in Texas construction contracts, such provisions are voidable by a party obligated by the contract or agreement to perform the work. By submission of this proposal, Vendor acknowledges this law and if Vendor enters into a construction contract with a Texas TIPS Member under this procurement, Vendor certifies compliance.
200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, glass, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Measurements and arithmetic conventions All measurements and calculations shall be in the metric system and calculations done to 2 (two) decimal places, with the third digit of 5 (five) or above being rounded up and below 5 (five) being rounded down.
Requirements of the State of Kansas 1. The contractor shall observe the provisions of the Kansas Act against Discrimination (Kansas Statutes Annotated 44-1001, et seq.) and shall not discriminate against any person in the performance of work under the present contract because of race, religion, color, sex, disability, and age except where age is a bona fide occupational qualification, national origin or ancestry; 2. In all solicitations or advertisements for employees, the contractor shall include the phrase, "Equal Opportunity Employer", or a similar phrase to be approved by the "Kansas Human Rights Commission"; 3. If the contractor fails to comply with the manner in which the contractor reports to the "Kansas Human Rights Commission" in accordance with the provisions of K.S.A. 1976 Supp. 44-1031, as amended, the contractor shall be deemed to have breached this contract and it may be canceled, terminated or suspended in whole or in part by the contracting agency; 4. If the contractor is found guilty of a violation of the Kansas Act against Discrimination under a decision or order of the "Kansas Human Rights Commission" which has become final, the contractor shall be deemed to have breached the present contract, and it may be canceled, terminated or suspended in whole or in part by the contracting agency; 5. The contractor shall include the provisions of Paragraphs 1 through 4 inclusive, of this Subsection B, in every subcontract or purchase so that such provisions will be binding upon such subcontractor or vendor.
Particular Methods of Procurement of Goods and Works International Competitive Bidding. Goods and works shall be procured under contracts awarded on the basis of International Competitive Bidding.
CFR PART 200 Domestic Preferences for Procurements As appropriate and to the extent consistent with law, the non-Federal entity should, to the greatest extent practicable under a Federal award, provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). The requirements of this section must be included in all subawards including all contracts and purchase orders for work or products under this award. For purposes of 2 CFR Part 200.322, “Produced in the United States” means, for iron and steel products, that all manufacturing processes, from the initial melting stag through the application of coatings, occurred in the United States. Moreover, for purposes of 2 CFR Part 200.322, “Manufactured products” means items and construction materials composed in whole or in part of non-ferrous metals such as aluminum, plastics and polymer-based products such as polyvinyl chloride pipe, aggregates such as concrete, class, including optical fiber, and lumber. Pursuant to the above, when federal funds are expended by ESC Region 8 and TIPS Members, Vendor certifies that to the greatest extent practicable Vendor will provide a preference for the purchase, acquisition, or use of goods, products, or materials produced in the United States (including but not limited to iron, aluminum, steel, cement, and other manufactured products). Does vendor agree? Yes
Conventions For purposes of this Article XIII, Party A means the Carrier from which a telephone number is Ported, and Party B means the carrier to which a telephone number is ported.
LEAVE FOR REGULATORY BUSINESS AS PER THE TEACHERS’ ACT 1. Upon written request to the Superintendent or designate from the Ministry of Education, an employee who is appointed or elected to the BC Teachers’ Council or appointed to the Disciplinary or Professional Conduct Board shall be entitled to a leave of absence with pay and shall be deemed to be in the full employ of the board as defined in Article G.6.1. 2. Upon written request to the superintendent or designate from the Ministry of Education, a teacher teaching on call (TTOC) who is appointed or elected to the BC Teachers’ Council or appointed to the Disciplinary and Professional Conduct Board shall be considered on leave and shall be deemed to be in the full employ of the Board as defined in Article A.10.1 above. TTOCs shall be paid in accordance with the collective agreement. 3. Leave pursuant to Article A.10.1 and A.10.2 above shall not count toward any limits on the number of days and/or teachers on leave in the provisions in Article G.6.
