MMX Sa
MMX Sa Sample Clauses
Related to MMX Sa
Unbundled Copper Loops (UCL) 2.4.1 BellSouth shall make available Unbundled Copper Loops (UCLs). The UCL is a copper twisted pair Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters) and is not intended to support any particular telecommunications service. The UCL will be offered in two types – Designed and Non-Designed.
Unbundled Copper Loop – Designed (UCL-D) 2.4.2.1 The UCL-D will be provisioned as a dry copper twisted pair (2- or 4-wire) Loop that is unencumbered by any intervening equipment (e.g., filters, load coils, range extenders, digital loop carrier, or repeaters). 2.4.2.2 A UCL-D will be 18,000 feet or less in length and is provisioned according to Resistance Design parameters, may have up to 6,000 feet of bridged tap and will have up to 1300 Ohms of resistance. 2.4.2.3 The UCL-D is a designed circuit, is provisioned with a test point, and comes standard with a DLR. OC is a chargeable option for a UCL-D; however, OC is always required on UCLs where a reuse of existing facilities has been requested by Telepak Networks. 2.4.2.4 These Loops are not intended to support any particular services and may be utilized by Telepak Networks to provide a wide-range of telecommunications services as long as those services do not adversely affect BellSouth’s network. This facility will include a Network Interface Device (NID) at the customer’s location for the purpose of connecting the Loop to the customer’s inside wire. 2.4.2.5 Upon the Effective Date of this Agreement, Unbundled Copper Loop – Long (UCL-L) elements will no longer be offered by BellSouth and no new orders for UCL-L will be accepted. Any existing UCL-Ls that were provisioned prior to the Effective Date of this Agreement will be grandfathered at the rates set forth in the Parties’ interconnection agreement that was in effect immediately prior to the Effective Date of this Agreement. Existing UCL-Ls that were provisioned prior to the Effective Date of this Agreement may remain connected, maintained and repaired according to BellSouth’s TR73600 and may remain connected until such time as they are disconnected by Telepak Networks or BellSouth provides ninety
Tandem Transit Traffic 12.1 As used in this Section, Tandem Transit Traffic is Telephone Exchange Service traffic that originates on Onvoy's network, and is transported through Frontier’s Tandem to the subtending End Office or its equivalent of another carrier (CLEC, ILEC other than Frontier, Commercial Mobile Radio Service (CMRS) carrier, or other LEC (“Other Carrier”). Neither the originating nor terminating customer is a Customer of Frontier. Subtending End Offices shall be determined in accordance with and as identified in the Local Exchange Routing Guide (LERG). For the avoidance of any doubt, under no circumstances shall Frontier be required to transit traffic through a Frontier Tandem to a Central Office that the LERG does not identify as subtending that particular Frontier Tandem. Switched Exchange Access Service traffic is not Tandem Transit Traffic. 12.2 Tandem Transit Traffic Service provides Onvoy with the transport of Tandem Transit Traffic as provided below. 12.3 Tandem Transit Traffic may be routed over the Interconnection Trunks described in Sections 2 through 6 of this Attachment. Onvoy shall deliver each Tandem Transit Traffic call to Frontier’s Tandem with CCS and the appropriate Transactional Capabilities Application Part (“TCAP”) message to facilitate full interoperability of CLASS Features and billing functions. 12.4 Onvoy may use Tandem Transit Traffic Service only for traffic that originates on Onvoy’s network and only to send traffic to an Other Carrier with whom Onvoy has a reciprocal traffic exchange arrangement (either via written agreement or mutual tariffs) that provides for the Other Carrier, to terminate or complete traffic originated by Onvoy and to bill Onvoy, and not to bill Frontier, for such traffic. Onvoy agrees not to use Frontier’s Tandem Transit Traffic Service to send traffic to an Other Carrier with whom Onvoy does not have such a reciprocal traffic exchange arrangement or to send traffic that does not originate on Onvoy’s network. 12.5 Onvoy shall pay Frontier for Tandem Transit Traffic Service at the rates specified in the Pricing Attachment. Frontier will not be liable for compensation to any Other Carrier for any traffic that is transported through Frontier’s Tandem and Frontier reserves the right to assess to Onvoy any additional charges or costs any Other Carrier imposes or levies on Frontier for the delivery or termination of such traffic, including any Switched Exchange Access Service charges. If Frontier is billed by any Other Carrier for any traffic originated by Onvoy, Frontier may provide notice to Onvoy of such billing. Upon receipt of such notice, Onvoy shall immediately stop using Frontier’s Tandem Transit Traffic Service to send any traffic to such Other Carrier until it has provided to Frontier certification that the Other Carrier has removed such billed charges from its bill to Frontier and that the Other Carrier will not bill Frontier for any traffic originated by Onvoy. Such certification must be signed by an authorized officer or agent of the Other Carrier and must be in a form acceptable to Frontier. 12.6 If Onvoy uses Tandem Transit Traffic Service for traffic volumes that exceed the Centum Call Seconds (Hundred Call Seconds) busy hour equivalent of 200,000 combined minutes of use per month (a DS1 equivalent) to the subtending End Office of a particular Other Carrier for any month (the “Threshold Level”). Onvoy shall use good faith efforts to establish direct interconnection with such Other Carrier and reduce such traffic volumes below the Threshold Level. If Frontier believes that Xxxxx has not exercised good faith efforts promptly to obtain such direct interconnection, either Party may use the Dispute Resolution processes of this Agreement. 12.7 If Onvoy fails to comply with Section 12 of this Attachment, such failure shall be a material breach of a material provision of this Agreement and Frontier may exercise any and all remedies under this Agreement and Applicable Law for such breach. 12.8 If or when a third party carrier plans to subtend an Onvoy switch, then Onvoy shall provide written notice to Frontier at least ninety (90) days before such subtending service arrangement becomes effective so that Frontier may negotiate and establish direct interconnection with such third party carrier. Upon written request from Frontier, Onvoy shall offer to Frontier a service arrangement equivalent to or the same as Tandem Transit Traffic Service provided by Frontier to Onvoy as defined in this Section such that Frontier may terminate calls to a Central Office or its equivalent of a CLEC, ILEC other than Frontier, CMRS carrier, or other LEC, that subtends an Onvoy Central Office or its equivalent (“Reciprocal Tandem Transit Service”). Onvoy shall offer such Reciprocal Transit Service arrangements under terms and conditions of an amendment to this Agreement or a separate agreement no less favorable than those provided in this Section. 12.9 Neither Party shall take any actions to prevent the other Party from entering into a direct and reciprocal traffic exchange arrangement with any carrier to which it originates, or from which it terminates, traffic.
Unbundled Copper Loop – Non-Designed (UCL-ND 2.4.3.1 The UCL–ND is provisioned as a dedicated 2-wire metallic transmission facility from BellSouth’s Main Distribution Frame to a customer’s premises (including the NID). The UCL-ND will be a “dry copper” facility in that it will not have any intervening equipment such as load coils, repeaters, or digital access main lines (“DAMLs”), and may have up to 6,000 feet of bridged tap between the end user’s premises and the serving wire center. The UCL-ND typically will be 1300 Ohms resistance and in most cases will not exceed 18,000 feet in length, although the UCL-ND will not have a specific length limitation. For loops less than 18,000 feet and with less than 1300 Ohms resistance, the loop will provide a voice grade transmission channel suitable for loop start signaling and the transport of analog voice grade signals. The UCL-ND will not be designed and will not be provisioned with either a DLR or a test point. 2.4.3.2 The UCL-ND facilities may be mechanically assigned using BellSouth’s assignment systems. Therefore, the Loop Make Up process is not required to order and provision the UCL-ND. However, Lightyear can request Loop Make Up for which additional charges would apply. 2.4.3.3 At an additional charge, BellSouth also will make available Loop Testing so that Lightyear may request further testing on the UCL-ND. Rates for Loop Testing are as set forth in Exhibit B of this Attachment. 2.4.3.4 UCL-ND loops are not intended to support any particular service and may be utilized by Lightyear to provide a wide-range of telecommunications services so long as those services do not adversely affect BellSouth’s network. The UCL-ND will include a Network Interface Device (NID) at the customer’s location for the purpose of connecting the loop to the customer’s inside wire. 2.4.3.5 Order Coordination (OC) will be provided as a chargeable option and may be utilized when the UCL-ND provisioning is associated with the reuse of BellSouth facilities. Order Coordination -Time Specific (OC-TS) does not apply to this product. 2.4.3.6 Lightyear may use BellSouth’s Unbundled Loop Modification (ULM) offering to remove bridge tap and/or load coils from any loop within the BellSouth network. Therefore, some loops that would not qualify as UCL-ND could be transformed into loops that do qualify, using the ULM process.
Non-Arm’s Length Transactions To the knowledge of the Company, after due inquiry, except as disclosed in writing to the Underwriters or in the Registration Statement, the Time of Sale Information and the Prospectuses, neither the Company nor any subsidiary is a party to any contract, agreement or understanding with any officer, director, employee or any other person not dealing at arm’s length with the Company or any subsidiary which is required to be disclosed by applicable Canadian Securities Laws.
Fund/SERV Transactions If the parties choose to use the National Securities Clearing Corporation’s Mutual Fund Settlement, Entry and Registration Verification (“Fund/SERV”) or any other NSCC service, the following provisions shall apply: The Company and the Fund or its designee will each be bound by the rules of the National Securities Clearing Corporation (“NSCC”) and the terms of any NSCC agreement filed by it or its designee with the NSCC. Without limiting the generality of the following provisions of this section, the Company and the Fund or its designee will each perform any and all duties, functions, procedures and responsibilities assigned to it and as otherwise established by the NSCC applicable to Fund/SERV, the Mutual Fund Profile Service, the Networking Matrix Level utilized and any other relevant NSCC service or system (collectively, the “NSCC Systems”). Any information transmitted through the NSCC Systems by any party or its designee to the other or its designee and pursuant to this Agreement will be accurate, complete, and in the format prescribed by the NSCC. Each party or its designee will adopt, implement and maintain procedures reasonably designed to ensure the accuracy of all transmissions through the NSCC Systems and to limit the access to, and the inputting of data into, the NSCC Systems to persons specifically authorized by such party. On each day on which the New York Stock Exchange is open for trading and on which the Fund calculates its net asset value pursuant to the rules of the SEC (“Business Day”), the Company shall aggregate and calculate the net purchase and redemption orders for each Account received by the Company by the close of the New York Stock Exchange (generally, 4:00 p.m. Eastern Time) (the “Close of Trading”) on the Business Day. The Company shall communicate to the Fund or its designee for that Business Day, by Fund/SERV, the net aggregate purchase or redemption orders (if any) for each Account received by the Close of Trading on such Business Day (the “Trade Date”) no later than 7:00 a.m. Eastern Time (or such other time as may be agreed by the parties from time to time) (the “Fund/SERV Transactions Deadline”) on the Business Day following the Trade Date. All such aggregated orders communicated to the Fund or its designee by the Fund/SERV Transactions Deadline on the Business Day following the Trade Date shall be treated by the Fund or its designee as if received prior to the Close of Trading on the Trade Date. All orders received by the Company after the Close of Trading on a Business Day shall not be aggregated with Orders received by the Company prior to the Close of Trading on such Business Day and shall be communicated to BRIL or its designee as part of an aggregated order no sooner than after the FUND/SERV Transactions Deadline or such other time as may be agreed by the parties from time to time) the following Business Day. Cash settlement shall be transmitted pursuant to the normal NSCC settlement process. In the case of delayed settlement, the Fund or its designee shall make arrangements for the settlement of redemptions by wire no later than the time permitted for settlement of redemption orders by the 1940 Act. Unless otherwise informed in writing, such redemption wires should be sent to an account specified by the Company and agreed to by Fund Parties.
Unbundled Copper Sub-Loop (UCSL) is a copper facility of any length provided from the cross-box in the field up to and including the end-user’s point of demarcation. If available, this facility will not have any intervening equipment such as load coils between the end-user and the cross-box.
Compensatory Time Cash Out All compensatory time must be used by June 30th of each year. If compensatory time balances are not scheduled to be used by the employee by April of each year, the supervisor will contact the employee to review their schedule. The employee’s compensatory time balance will be cashed out every June 30th or when the employee: 1. Leaves state service for any reason; 2. Transfers to a position in their institution with different funding sources; or 3. Transfers to another state agency or institution.
Target Net Assets The Company agrees that the Target Business that it acquires must have a fair market value equal to at least 80% of the balance in the Trust Account at the time of signing the definitive agreement for the Business Combination with such Target Business (excluding taxes payable and the Deferred Underwriting Commissions). The fair market value of such business must be determined by the Board of Directors of the Company based upon standards generally accepted by the financial community, such as actual and potential sales, earnings, cash flow and book value. If the Board of Directors of the Company is not able to independently determine that the target business meets such fair market value requirement, the Company will obtain an opinion from an independent investment banking firm or another independent entity that commonly renders valuation opinions with respect to the satisfaction of such criteria. The Company is not required to obtain an opinion as to the fair market value if the Company’s Board of Directors independently determines that the Target Business does have sufficient fair market value.
Unbundled Sub-Loop Feeder 2.8.4.1 Unbundled Sub-Loop Feeder (USLF) provides connectivity between BellSouth's central office and cross-box (or other access point) that serves an end user location. 2.8.4.2 USLF utilized for voice traffic can be configured as 2-wire voice (USLF-2W/V) or 4-wire voice (USLF-4W/V). 2.8.4.3 USLF utilized for digital traffic can be configured as 2-wire ISDN (USLF-2W/I); 2-wire Copper (USLF-2W/C); 4-wire Copper (USLF-4W/C); 4-wire DS0 level loop (USLF-4W/D0); or 4-wire DS1 and ISDN (USLF-4W/DI). 2.8.4.4 USLF will provide access to both the equipment and the features in the BellSouth central office and BellSouth cross box necessary to provide a 2W or 4W communications pathway from the BellSouth central office to the BellSouth cross- box. This element will allow for the connection of Lightyear’s loop distribution elements onto BellSouth's feeder system.
